Related Manuals for Extron electronics DTP DVI 230
Summary of Contents for Extron electronics DTP DVI 230
- Page 1 User Guide HDMI & DVI Extenders DTP DVI 230 DVI Twisted Pair Extender 68-2341-01 Rev. B 06 13...
-
Page 2: Safety Instructions
Safety Instructions Safety Instructions • English Chinese Simplified （简体中文） WARNING: This symbol, , when used on the product, is intended 警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 to alert the user of the presence of uninsulated dangerous voltage 电压， 有触电危险。 within the product’s enclosure that may present a risk of electric shock. - Page 3 FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
-
Page 5: Table Of Contents
Installation and Operation ........3 Mounting the Units ..........3 Connections ............3 Transmitter Connections ......... 3 Receiver Connections ........5 Connector and Cable Details ......6 Operation ............9 DTP DVI 230 Tx/Rx Transmitter and Receiver • Table of Contents... - Page 6 DTP DVI 230 Tx/Rx Transmitter and Receiver • Introduction...
-
Page 7: Introduction
Figure 1. Typical Transmitter and Receiver Application The DTP DVI 230 Tx/Rx units are housed in quarter rack width metal enclosures. They can be set on a tabletop or mounted in a rack, under or through furniture. The receiver can also be mounted on a projector bracket. -
Page 8: Tp Cable Advantages
Termination of the cable with RJ‑45 connectors is simple, quick, and economical. NOTE: Do not use Extron UTP23SF‑4 Enhanced Skew‑Free AV UTP cable or STP201 cable to link the transmitter and receiver. The DTP DVI 230 Tx/Rx does not work properly with these cables. Control Communications The RS‑232 and IR communications are a passive pass‑through only. -
Page 9: Installation And Operation
Installation and Operation This section describes the installation and the operation of the DTP DVI 230 Tx/Rx Extender, including: • Mounting the Units • Connections • Operation Mounting the Units Mounting instructions can be found in Mounting the Transmitter or Receiver page 10. - Page 10 • If you have removed the ground jumpers (see Disconnecting the Ground on page 11) because of ground potential differences, one DTP DVI 230 unit cannot remotely power the other unit. Each unit requires a local power supply. DTP DVI 230 Tx/Rx Transmitter and Receiver • Installation and Operation...
-
Page 11: Receiver Connections
• If you have removed the ground jumpers (see Disconnecting the Ground page 11) because of ground potential differences, the DTP DVI 230 cannot extend analog audio. No analog audio is output. • The length of exposed wires is critical. The ideal length is 3/16 inch (5 mm). -
Page 12: Connector And Cable Details
TP Cable Termination NOTE: Do not use Extron UTP23SF‑4 Enhanced Skew‑Free AV UTP cable or STP201 cable to link the transmitter and receiver. The DTP DVI 230 Tx/Rx does not work properly with these cables. DTP DVI 230 Tx/Rx Transmitter and Receiver • Installation and Operation... - Page 13 Supported cables — The DTP DVI 230 is compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair (F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. Cable recommendations — Extron recommends using the following practices to achieve full transmission distances up to 230 feet (70 m) and reduce transmission errors.
-
Page 14: Power Supply Wiring
If you have removed the ground jumpers (see Disconnecting the Ground page 11) because of ground potential differences, one DTP DVI 230 unit cannot remotely power the other unit. Each unit requires a local power supply. Figure 6 shows how to wire the connector. Use the supplied tie‑wrap to strap the power cord to the extended tail of the connector. -
Page 15: Operation
If the other devices are not turned on before the video source, the image may not appear. DTP DVI 230 Tx/Rx Transmitter and Receiver • Installation and Operation... -
Page 16: Reference Information
The 1‑inch high, quarter rack width DTP DVI 230 transmitter or receiver can be placed on a table, mounted in a rack, or mounted under a desk or table. The receiver can also be mounted on a projector bracket. -
Page 17: Ul Rack-Mounting Guidelines
(as suggested by a missing or unstable picture), remove the ground connection between the units as follows: NOTE: Once you have removed the ground jumpers, the DTP DVI 230 cannot extend analog audio and one unit cannot remotely power the other. No analog audio is output and each unit requires a local power supply. - Page 18 Obtain a second 12 V power supply (one supply is provided with the transmitter and normally powers both units), and locally power both units (see Power supply wiring on page 8). DTP DVI 230 Tx/Rx Transmitter and Receiver • Reference Information...
- Page 19 Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to: USA, Canada, South America,...