Table of Contents
Advertisement
installation
STEP #2: OUTER SHELL INSTALLATION
1. Slide outer shell back into the existing firebox, ensure the vent slide
plate is properly engaged with the outer shell.
Move the outer shell back until the left and right flanges contact
the existing firebox.
2. Adjust the outer shell legs to the setting noted for your specific
installation. If these settings are not adhered to, the surround will not fit
correctly.
3. Attach the vent slide plate to the outer shell with one sheet metal
screw as shown in Figure 12.1. Refer to the applicable existing appli-
ance for correct measurements before securing outer shell in position.
4. Ensure the unit is set at the correct height and the outer shell is square
and centered, fasten the outer shell to the existing firebox using self
tapping screws.
STEP #3: FIREBOX INSTALLATION
1. Ensure thermodiscs and thermodisc brackets are in
place.
2. Install the firebox into the outer shell by sliding the
drafthood bottom onto the drafthood slide until you are
able to install 4 screws to secure the firebox. Use care
to avoid damaging the wire harness.
Note: 2 of the screws along with panel brackets to be
installed on the lower inside of the firebox.
3. Unit is installed correctly when the flanges that se-
cure the firebox to the outer shell contact. Ensure the
unit is centered within the existing firebox, attach the
outer shell to the existing firebox using 4 x sheet metal
screws.
4. Install 2 self tapping screws at the front edge corners of
the drafthood bottom to secure the drafthood.
5. Install 1 x Phillips screw to fasten drafthood. Install 2 x
Phillips screws to secure left and right side of thermo-
disc bracket.
56
|
Regency
E18E-11 Gas Fireplace Insert
®
Existing Firebox
Leg Height
Upper Drafthood
Baffle
Wire Harness
Surround
Mounting
Bracket
Left
Control Box
Step #3: Firebox Installation
1) Install the Upper Drafthood Baffle onto the Outer Shell using 4 screws provided.
2) The Firebox installs into the Outer Shell by sliding the Drafthood Bottom onto the Drafthood
ZC box existing Unit
Slide until you are able to install 4 screws to secure the Firebox, 2 located in each inner lower
Firebox Sides. While you are installing the Firebox, care must be taken to avoid damaging the
Wire Harness until it can be secured in following steps.
EP28
3) The unit is installed correctly when the flanges that secure the Firebox to the Outer Shell are
touching. Making sure that the unit is centered within the existing firebox, attach the Outer
28F - 28F2
Shell to the existing firebox using 4x sheet metal screws as shown in Step #2.
Montigo 36SR
4) Install 2 screws at the lower front edge corners of the Drafthood Bottom to secure the
Drafthood. These screws may need to be self drilling to screw into or through the existing
Firesong 220N
firebox.
5) Make sure that your unit is sitting at the correct height and that the Outer Shell is square
and centered in the install, fasten the Outer Shell to the existing firebox using self drilling and
tapping screws.
6) Locate and install the Surround Mounting Brackets Right and Left.
7) Using 2 screws provided, install the Control Box into a slot provided in the Surround
Mounting Bracket Left.
Vent Slide Plate
attachement screw
Outer Shell Screws (x4)
Outer Shell Legs (x2)
Fastening Screws
Diagram 12.1
Drafthood Slide
Surround Mounting
Bracket Right
Diagram 12.2
Measured from
Measured from side of
Top of ZC box
ZC box
8-7/16" (215mm)
1-7/16" (37mm)
7-3/16" (183mm)
1-1/2" (39mm)
6-3/8" (162mm)
1-9/16" (40mm)
8-3/16" (208mm)
2-1/8" (54mm)
Vent Slide Plate
Step #2:
The E
installed
making it
locate an
compone
support t
appliance
installed
no conne
the field.
1) Slide t
into the e
carefull t
Slide Plat
slide prov
Move the
the left an
against th
2) Adjust
to the set
installatio
correct, t
fit correct
installatio
3) Attach
Outer Sh
screw as
Outer Sh
this point
Drafthood
Bottom
Advertisement
Table of Contents
