Table of Contents
Advertisement
WARNING:
If the information in these instructions are not followed exactly,
a fi re or explosion may result causing property damage,
personal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable vapors and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualifi ed
installer, service agency or the gas supplier.
Tested by:
918-671c
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
E21 Gas Insert
MODELS: E21-NG3 Natural Gas E21-LP3 Propane
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
Owners &
Installation Manual
www.regency-fi re.com
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you
cannot reach your gas
supplier, call the fi re department.
01/17/12
Advertisement
Table of Contents
Related Manuals for Regency E21-NG3
Summary of Contents for Regency E21-NG3
- Page 1 Owners & E21 Gas Insert Installation Manual www.regency-fi re.com MODELS: E21-NG3 Natural Gas E21-LP3 Propane WARNING: FOR YOUR SAFETY If the information in these instructions are not followed exactly, What to do if you smell gas: Do not try to light any appliance a fi...
- Page 2 Gas Fireplace Series has been designed to provide you with all the warmth and charm of a fi replace, at the fl ick of a switch. The models E21-NG3 and E21-LP3 of this series have been approved by Warnock Hersey for safety. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow.
- Page 3 INSTALLATION 40-1/8" 9-7/8” Low Profi le Faceplate Dimensions * Standard size shown, custom size also available. ® Regency E21-3 Gas Fireplace Insert...
-
Page 4: Table Of Contents
Optional Bay Front............22 Bay Louvers..............22 Warranty ..............44 Conversion from NG to LP ..........23 Full Screen doors ............26 Low profi le faceplate installation........28 Low profi le hearth trim installation .......30 Remote Control ............31 Wall Switch ..............31 ® Regency E21-3 Gas Fireplace Insert... -
Page 5: Safety Label
SAFETY LABEL This is a copy of the label that accompanies each Regency ® Gas Insert. We have printed a copy of the contents here for your review. The safety label is located on the front inside base of the unit visible when the bottom louver is open. -
Page 6: Requirements
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. ® Regency E21-3 Gas Fireplace Insert... -
Page 7: Installation
YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE. CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPE- CIALLY THE FIREPLACE GLASS, AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. ® Regency E21-3 Gas Fireplace Insert... -
Page 8: Important Message
fi replace SAVE THESE insert. INSTRUCTIONS 12) Wear gloves and safety glasses for protection while doing required maintenance. The Regency ® Gas Fireplace must be installed in accordance with these instructions. Carefully read 13) Ensure adequate combustion and ventilation air. -
Page 9: Policy For Solid Fuel Burning & Factory Built Fireplaces
FUEL BURNING & FACTORY BUILT Diagram shows the minimum fi replace opening 1) Locate your appliance. Refer to the "Clear- ® required to be able to install the Regency ances to Combustibles" and "Minimum FIREPLACES fi replace insert. Fireplace Clearances" sections. -
Page 10: Clearances To Combustibles
14 inches (356mm). The minimum combustible board. height from the top of the louver to the ceiling is 36 inches (914mm). aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa aaaaa ® Regency E21-3 Gas Fireplace Insert... -
Page 11: Gas Connection
Variable Speed: 127 CFM, thermally with a soap and water solution or gas activated leak detector. Do not use open fl ame NATURAL GAS E21-NG3 for leak testing. For altitude: 2000 ft - 4500 ft. Burner Inlet Orifi ce Size: 44 DMS Max. -
Page 12: Wiring Diagrams
(grounding) plug for cause improper and dangerous your protection against shock hazard operation. and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. ® Regency E21-3 Gas Fireplace Insert... -
Page 13: Flue Connector Installation
4) Replace the screw holding the plate just before completely pushing the appliance into the fi replace. Note: Do not operate unit if fl ue connector is not fastened in original position. ® Regency E21-3 Gas Fireplace Insert... -
Page 14: Gas Pipe Pressure Testing
fi replaces. The offset fl ue adaptor requires the code requirements. which it is to be operating. use of a 3" liner. The Regency ® Insert incorporates its own Follow CAN/CGA B149 (in Canada) or ANSI internal draft hood, so no additional external Z223.1 (in the USA) requirements, and any... -
Page 15: Valve Description
fi rst (see diagram for correct Note: Aeration Adjustment should only be positioning), then the two side panels. Slide performed by an authorized Regency ® the side brick panel into place from the front Installer at the time of installation or of the fi... -
Page 16: Log Set Installation
1) Carefully remove the logs from the box and unwrap them. The logs are fragile, handle with care - do not force into position. 2) Spread vermiculite around the fi rebox base. Then take some embers and spread them over the vermiculite as shown. 27-24 ® Regency E21-3 Gas Fireplace Insert... - Page 17 7) Fit the top end of log 27-27 into the pin in log 27-23 and rest the bottom end of log 27-27 against the 2nd grate post. 27-27 27-25 27-23 6) Fit log 27-26 into the pins on the front right side of the burner. 27-27 27-26 2nd Grate Post ® Regency E21-3 Gas Fireplace Insert...
- Page 18 9) Fit the left end of log 27-29 into the pin on the front left side of the burner (in front of the 1st grate post) and rest the right end of log 27-29 onto the notch on log 27-27. 27-24 27-27 27-26 27-29 Notch 1st Grate Post ® Regency E21-3 Gas Fireplace Insert...
- Page 19 Ensure not to cover any burner ports. 13) Separate platinum embers and place on the burner just in front of the logs. Avoid stacking platinum embers. Completed Log Set Installation 27-28 27-27 27-23 27-24 27-30 27-29 27-26 27-25 ® Regency E21-3 Gas Fireplace Insert...
-
Page 20: Faceplate & Trim Installation
3) Using the connectors provided, join the left side trim (with the ON/OFF switch) to the Diagram 3 top trim. See diagram 2. Connect the right side trim to the top trim. ® Regency E21-3 Gas Fireplace Insert... -
Page 21: Flush Glass
Replacement of the glass panel(s) should be done by a qualifi ed service person. 3) Place the Bottom Louver near the hinge. Flip hinge over the Bottom Louver and secure using 3 screws. Hinge Location Bottom Louver ® Regency E21-3 Gas Fireplace Insert... - Page 22 Shut off gas supply. Unplug or disconnect power source to stove. Remove glass front (see Door Glass Fig.2 Replacement section in the manual). Remove logs and brick panels (if installed). ® Regency E21-3 Gas Fireplace Insert...
-
Page 23: Installation Of The Dc Sparker
11/32 nut 18) Re-assemble the black protection cap star washer to secure in place. (Fig. 6). 24) Locate the Piezo Ignitor situated at the side of valve. Piezo Ignitor Fig. 6 ® Regency E21-3 Gas Fireplace Insert... - Page 24 38) Check inlet and outlet pressures. 39) Check operation of fl ame control. 40) Check for proper fl ame appearance and glow on logs. Installer Notice: These instructions must be left with the appliance. ® Regency E21-3 Gas Fireplace Insert...
-
Page 25: Full Screen Doors
It is held in place by magnets. 2) Lift the unit up slightly and push down on the corners of the Bottom Trim Bracket and slide under unit. Screw Push in Corners Top Frame Bottom Trim Bracket ® Regency E21-3 Gas Fireplace Insert... - Page 26 Hold the door at a 45 degree angle to avoid scratching the faceplate. Hinge 6) Place Bottom Frame near hinge. Flip hinge over Bottom Frame and secure with 3 screws each. Screen Door Hinge Location Bottom Frame 8) Close screen doors. ® Regency E21-3 Gas Fireplace Insert...
-
Page 27: Low Profi Le Faceplate Installation
Attach the 2 bottom louver hinges to the bottom fl ange on the fi rebox using 2 screws per hinge. Diagram 3 3) Connect the female ends of the ON/OFF switch - to the ON/OFF switch in the control box. Diagram 7 Diagram 4 ® Regency E21-3 Gas Fireplace Insert... - Page 28 Diagram 9. Diagram 9 Take the outer faceplate, line up the openings on the left and right legs and install onto the inner faceplate panel pins. Outer faceplate Inner faceplate panel pins Diagram 10 ® Regency E21-3 Gas Fireplace Insert...
-
Page 29: Low Profi Le Hearth Trim Installation
2) If screw holes are present on backing plate, secure the hearth trim to backing place with 2 screws on each side. Hearth Trim Clip Diagram 6–Hearth Trim Clip 5) Reinstall backing plate. Hearth Trim Diagram 3–Hearth Trim Secured to Backing Plate 6) Reinstall outer faceplate. ® Regency E21-3 Gas Fireplace Insert... -
Page 30: Remote Control
REMOTE CONTROL WALL SWITCH WALL THERMOSTAT Use the Regency Remote Control Kit approved 1) Run the wire through the right or left side A wall thermostat may be installed if desired, for this unit. Use of other systems may void inlet opening. -
Page 31: Final Check
WITHOUT THE GLASS FRONT IN the gas control knob. The pilot fl ame should PLACE. continue to burn. If the pilot does not remain lit, repeat operation allowing a longer period before releasing gas control knob. ® Regency E21-3 Gas Fireplace Insert... -
Page 32: Copy Of Lighting Plate Instructions
3) Turn off all electric power to the appliance if service is to be performed. Pilot must be shut off during prolonged non use periods 918-475 to conserve fuel. DO NOT REMOVE THIS INSTRUCTION PLATE ® Regency E21-3 Gas Fireplace Insert... -
Page 33: Automatic Convection Fan Operation
If you have an incorrect fl ame pattern, operation of a gas regulator or valve. unit on. If the top louvers start to discolour, ® contact your Regency dealer for further check the door gasket seal and replace if instructions. -
Page 34: Door Glass Replacement
REMOVING VALVE fi rebox bottom and 4 screws on the rear REPLACEMENT ASSEMBLY wall., and lift out. Your Regency ® stove is supplied with high 1) Disconnect the power. temperature, 5 mm Neoceram ceramic glass that will withstand the highest heat that your unit will 2) Shut off the gas. -
Page 35: Parts List
532-914 Flush Louver (set)-Steel/Black Top Flush Louver Bottom Flush Louver 532-901 Brick Panel Set - Standard Brown 532-902 Brick Panel Set - Standard Red 532-903 Brick Panel Set - Herringbone Brown BRICK PANEL SET ® Regency E21-3 Gas Fireplace Insert... -
Page 36: Burner Assembly & Log Set
Electrode 904-162 #43 Orifi ce (NG) 904-163 #54 Orifi ce (LP) 402-526 Grate/Diffuse Assembly 533-535 Burner Assembly - NG/LP 533-930 Complete Log Set 534-969 Conversion to Propane Kit *Not available as a replacement part. ® Regency E21-3 Gas Fireplace Insert... -
Page 37: Flush Front Assembly
107) 936-243 Gasket - Adhesive Backed 7/8" 153) Glass Side Trim 154) Flush Glass 157) Screw #10-24 x 1/2" Truss Head 158) 402-033 Flush Glass Bracket *Not available as a replacement part. FLUSH FRONT ® Regency E21-3 Gas Fireplace Insert... -
Page 38: Low Profi Le Faceplate
402-918 Faceplate & Trim (Set) - Zero Clearance Kit-Contour 532-927 Custom Faceplate 190) * Screw - #8 x 1/2" Black Self Tapping ® 199) 948-216 Regency Logo OVERSIZE 532-940 Full Screen Doors - Black FRONT VIEW LO GO LO GO... -
Page 39: Warranty
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect. The authorized selling dealer is responsible for all in-fi eld service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from unauthorized service persons or dealers. - Page 40 Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Regency and Energy are trademarks of FPI Fireplace Products International Ltd. Printed in Canada © Copyright 2012, FPI Fireplace Products International Ltd. All rights reserved.