Track Bouncing With Effects - Roland VS-1824 Owner's Manual

Adjust the Pan for Each Track and Check
the Volume Levels for Each Track
1. Press [PLAY (DISPLAY)] to return to the Playlist display.
2. Press [FADER/MUTE] so that "TR" is lit.
3. Press [PLAY] to begin song playback.
4. Adjust the volume and mix balance using Faders 5-8. The
presently monitored sound—track volumes and
panning—will be recorded to Track 9 and 10 just as you
now hear them.
Record the Track Bounce
1. Press [ZERO] to return to the beginning of the song.
2. While holding [REC], press the STATUS button for Track
9 or 10.
The STATUS button blinks red to indicate Record Ready.
3. Press [REC].
The button blinks red.
4. Press [PLAY].
The button lights green, and recording begins.
5. As the recording occurs, you can make adjustments to
the fader levels of the source Tracks 5-8. Any change you
make will be reflected in the bounce.
6. Press [STOP] at the end of the song.
7. Press [ZERO] to return to the beginning of the song.
8. Mute Tracks 5-8. Press the STATUS button for each of
these tracks once. The button will be unlit, indicating the
track is muted.
9. Press [PLAY] to hear the song. Use the track Fader 9 and
the Master fader to adjust the volume to a comfortable
listening level. You can now select empty Virtual Tracks
for Tracks 5-8 and record new material without
recording over the original material. It is a good idea to
keep your original takes stored on the Virtual Tracks in
case you need to re-bounce them later.
Chapter 4 Recording Operations

Track Bouncing With Effects

The process for bouncing tracks with effects is exactly as
explained above in "Track Bouncing," except follow the steps
outlined below in "Select the Source Tracks and the
Destination Tracks" to set up effects on each of the source
tracks as desired. For specific information on how to apply
effects to playback tracks, see Chapter 7, Using Internal Effects
(VS8F-2), p. 99.
Bouncing With Effects: Selecting Source
Tracks and Destination Tracks
1. Track 9 and 10 are linked as described in "Channel Link"
(p. 77).
2. Press [FADER/MUTE] so that "TR" is lit.
3. Hold [STOP], and press the STATUS buttons for source
Tracks 5-8.
The STATUS buttons light green.
4. Press the STATUS buttons for the destination Track 9
and 10 so it is lit orange.
5. Hold one of the STATUS buttons and press [CLEAR].
This clears all existing routing assignments.
6. Hold the STATUS button for Track 9 and press the
SELECT buttons for the source Tracks 5 and 7 so that
they blink.
7. Hold the STATUS button for Track 9, press the SELECT
button for EFFECT 1 RTN and EFFECT 2 RTN.
This action will include Effect 1 and Effect 2 Returns in
the track bounce.
* While continuing to hold the STATUS button for Track 9,
hold [SHIFT] and press the SELECT button for EFFECT 1
RTN and EFFECT 2 RTN. This action will include Effect
3 and Effect 4 Returns in the track bounce.
8. Hold the STATUS button for Track 10 and press the
SELECT buttons for the source Tracks 6 and 8 so that
they blink.
9. Hold the STATUS button for Track 10, press the SELECT
button for EFFECT 1 RTN and EFFECT 2 RTN.
This action will include Effect 1 and Effect 2 Returns in
the track bounce.
* While continuing to hold the STATUS button for Track
10, hold [SHIFT] and press the SELECT button for
EFFECT 1 RTN and EFFECT 2 RTN. This action will
include Effect 3 and Effect 4 Returns in the track bounce.
10. The source Tracks 5-8 can now be monitored on Channel
9 and 10.
Continue using the steps for bouncing tracks found
above in "Track Bouncing."
65