GE LPS-O Instruction Manual page 304

TIMESYNCH (General Setting 104) .............................. 2-3
TL5DROPOUT (Protection Setting 1102) .....................2-23
TL5PICKUP (Protection Setting 1101) .........................2-23
TL6DROPOUT (Protection Setting 1104) .....................2-23
TL6PICKUP (Protection Setting 1103) .........................2-23
TLOS1DO (Protection Setting 1410) ............................2-27
TLOS1PU (Protection Setting 1409) ............................2-27
TLOS2PU (Protection Setting 1411) ............................2-27
TLOS3PU (Protection Setting 1412) ............................2-27
TLOS4PU (Protection Setting 1413) ............................2-27
To ............................................................................... 1-1
TOC CURVES
see CURVES
TRANSFORMERS
potential .................................................................... 2-9
TRIP BUS CHECK ......................................................1-15
TRIP CIRCUIT MONITOR .................................... 1-15, 2-4
TRIP OUTPUT ASSIGNMENTS
three phase tripping .................................................. 2-4
TRIP OUTPUTS
monitoring ................................................................. 2-4
trip circuit monitor diagram ........................................ 2-4
TRIPIN_OUT (Protection Setting 1403) ...... 1-22, 1-24, 2-26
TROUBLESHOOTING .................................................. A-1
description ................................................................ 9-4
information status command ...................................... 9-4
locating defective boards .....................................9-5, 9-6
steps ........................................................................ 9-4
TWO-CHARACTERISTIC OPERATION ........................1-24
U
UNBALALARM (Protection Setting 507) .......................2-15
UNDERVOLTAGE TEST .............................................. 5-8
UNITID (General Setting 101) ................................1-2, 2-3
UNPACKING THE RELAY ............................................ 1-1
V
VERSION NUMBER ....................................................8-24
VERTICAL OUTLINE ................................................... 3-3
W
WARRANTY ................................................................ D-1
WEBSITE .................................................................... 1-1
installing LPSO-Link from Website ............................11-8
WEIGHT ...................................................................... 7-2
WIRING ...................................................................... 3-5
X
XPRESSION BUILDER
alarms .....................................................................1-15
assigning trip outputs ................................................ 2-3
boolean operators ....................................................13-5
breaker failure example .......................................... 13-16
compiling logic ....................................................... 13-16
configurable logic ...................................................... A-2
contact converter inputs ......................................... 13-14
x
INDEX
creating logic ......................................................... 13-13
current and voltage units .......................................... 13-9
custom programmability ..............................................1-6
description ............................................................... 13-1
design considerations ............................................... 13-5
designing logic ....................................................... 13-13
downloading logic ................................................... 13-16
flags ........................................................................ 13-8
input flags ................................................................ 13-9
installation ............................................................... 13-1
installation from internet ........................................... 13-4
latches ............................................................ 13-5, 13-6
modifying outputs ..................................................... 2-28
oscillography ............................................................ 1-12
output flags ............................................................ 13-12
overview .................................................................. 13-1
pickup delay timer .................................................... 13-7
pickup/dropout timer ................................................. 13-6
timers ...................................................................... 13-6
unbalanced current alarm ......................................... 2-15
uploading logic ....................................................... 13-13
Z
Z1P_TIME (Protection Setting 104) ...............................2-9
Z1PHASE (Protection Setting 101) ................................2-9
Z1PREACH (Protection Setting 102) ..............................2-9
Z2P_TIME (Protection Setting 205) ............................. 2-11
Z2PCHARANG (Protection Setting 203) ....................... 2-11
Z2PHASE (Protection Setting 201) ............ 2-10, 2-15, 2-16
Z2PHREACH (Protection Setting 202) ......................... 2-10
Z2TIMER (Protection Setting 204) ............................... 2-11
Z3P_TIME (Protection Setting 304) .................... 2-11, 2-12
Z3PCHARANG (Protection Setting 303) ....................... 2-12
Z3PHASE (Protection Setting 301) .............................. 2-11
Z3PHREACH (Protection Setting 302) ................ 2-11, 2-12
Z4_TIMERS (Protection Setting 405) ........................... 2-14
Z4P_TIME (Protection Setting 406) .................... 2-13, 2-14
Z4PCHARANG (Protection Setting 403) ....................... 2-14
Z4PHASE (Protection Setting 401) .............................. 2-13
Z4PHREACH (Protection Setting 402) ......................... 2-14
ZONE 1
phase distance ...........................................................2-9
phase reach ...............................................................2-9
phase timer ................................................................2-9
ZONE 1 PHASE REACH TEST
factory settings ........................................................ 5-10
user settings ............................................................ 6-10
ZONE 1 TO 4 PHASE-TO-PHASE REACH CALCULATIONS
for Zone Phase Reach tests ........................................6-8
ZONE 2
phase characteristic angle ........................................ 2-11
phase distance ......................................................... 2-10
phase reach ............................................................. 2-10
phase timer .............................................................. 2-11
ZONE 2 PHASE REACH TEST
factory settings ........................................................ 5-11
user settings ............................................................ 6-11
ZONE 3
phase characteristic angle ........................................ 2-12
phase reach ............................................................. 2-12
phase timer .............................................................. 2-11
ZONE 3 PHASE REACH TEST
LPS-O Line Protection System
GE Power Management