Bosch Security Escort SE2000 Series Training Manual page 167

Security Escort
<Area> element
Attributes
AreaID
FloorIcon
PagerGroupA
BitmapNumber
LocationText
MatrixSwitchText
<ProtectedAreaPoints> element
Attributes
ProtectedXArea1
ProtectedYArea1
Robert Bosch (SEA) Pte Ltd
Troubleshooting transponders, points, receivers, and alert units | en 167
Value
ID of the area. 0-79. This field should contain only numeric ASCII
characters.
Floor of the area. This field should contain only numeric ASCII
characters. Valid values are: 0 (Basement5), 1 (Basement4), 2
(Basement3), 3 (Basement2), 4 (Basement1), 5 (Tunnel), 6
(Basement), 7 (Ground), 8 (Outside), 9 (Floor 1), 10 (Floor 2), 11
(Floor 3), 12 (Floor 4), 13 (Floor 5), 14 (Floor 6), 15 (Floor 7), 16
(Floor 8), 17 (Floor 9), 18 (Floor 10), 19 (Floor 11), 20 (Floor 12),
21 (Floor 13), 22 (Floor 14), 23 (Floor 15), 24 (Floor 16), 25
(Floor 17), 26 (Floor 18), 27 (Floor 19), 28 (Floor 20), 29 (Floor
21), 30 (Floor 22), 31 (Floor 23), 32 (Floor 24), 33 (Floor 25), 34
(Floor 26), 35 (Floor 27), 36 (Floor 28), 37 (Floor 29), 38 (Floor
30), 39 (Floor 31), 40 (Floor 32), 41 (Floor 33), 42 (Floor 34), 43
(Floor 35), 44 (Floor 36), 45 (Floor 37), 46 (Floor 38), 47 (Floor
39), 48 (Floor 40), 49 (Floor 41), 50 (Floor 42), 51 (Floor 43), 52
(Floor 44), 53 (Floor 45), 54 (Floor 46), 55 (Floor 47), 56 (Floor
48), 57 (Floor 49), 58 (Floor 50), 59 (Floor 51), 60 (Floor 52), 61
(Floor 53), 62 (Floor 54), 63 (Floor 55), 64 (Floor 56), 65 (Floor
57), 66 (Floor 58), 67 (Floor 59), 68 (Floor 60), 69 (Floor 61), 70
(Floor 62), 71 (Floor 63), 72 (Floor 64), 73 (Floor 65), 74 (Floor
66), 75 (Floor 67), 76 (Floor 68), 77 (Floor 69), 78 (Floor 70), 79
(Floor 71), 80 (Floor 72), 81 (Floor 73), 82 (Floor 74), 83 (Floor
75), 84 (Floor 76), 85 (Floor 77), 86 (Floor 78), 87 (Floor 79), 88
(Floor 80), 89 (Floor 81), 90 (Floor 82), 91 (Floor 83), 92 (Floor
84), 93 (Floor 85), 94 (Floor 86), 95 (Floor 87), 96 (Floor 88), 97
(Floor 89), 98 (Floor 90), 99 (Floor 91), 100 (Floor 92), 101
(Floor 93), 102 (Floor 94), 103 (Floor 95), 104 (Floor 96), 105
(Floor 97), 106 (Floor 98), 107 (Floor 99).
Pager group. Default value is 0.
Graphic map of the area. 0-99. This field should contain only
numeric ASCII characters.
Location of the point. This field may be up to 100 characters. This
field may contain any printable ASCII character except the '?'.
ASCII value to control video matrix switch.
Value
st
1 coordinate point X of the area. This field should contain only
numeric ASCII characters.
st
1 coordinate point Y of the area. This field should contain only
numeric ASCII characters.
Training Manual 2017.08 | V2.18.1.0 | DOC