Checking The Ignition Pulse Gene,Ato - KTM 400 EXC AUS 2011 Repair Manual

3911GNITION SYSTEM
Battery winding resistance at: 20°C (68
OF)
• If the specification is not reached:
- Change the stator.
191
1
0.55 ... 0.74 rl
Measure the resistance between the specified points.
Q
Alternator, connector
CR
pin 1 (White) - Alternator, connector
CR
pin 1 (Yel-
low)
Chackillllha ilJlilion uba
~narator
Alternator
Light winding resistance at: 20°C 10.127 ... 0.172 rl
(68
OF)
• If the specification is not reached:
- Change the stator.
Condition
The crankshaft position sensor is disconnected.
Measure the resistance between the specified points.
AT
Q
Ignition pulse generator, connector
AT
pin 1 - Ignition pulse generator, con-
nector
AT
pin 2
Ignition pulse generator
Resistance at: 20°C (68
OF)
I
80 ... 120 rl
• If the specification is not reached:
- Replace the ignition pulse generator.
40058!>-l0
AT
400585-10
Measure the resistance between the specified points.
Ignition pulse generator, connector
AT
pin 1 - Measuring point
Ground (-)
1
Resistance
• If the specification is not reached:
- Replace the ignition pulse generator.
- Connect the special tool to the multimeter.
1
Peak voltage adapter (58429042000) (-- p. 256)
• Info
I
When using the peak voltage adapter, adjust the measuring range of the multi meter to DCV.
- Start the motorcycle for a check. (-- p. 11)
Check the ianition pulse lenerator voltage
AT
V
Measure the voltage between the specified points.
Ignition pulse generator, connector
AT
pin 1 - Ignition pulse generator, con-
nector
AT
pin 2
I
Ignition pulse generator
Voltage
12 ...
4 V
• If the specification is not reached:
40058~1O
3911GNITION SYSTEM
Battery winding resistance at: 20°C (68
OF)
• If the specification is not reached:
- Change the stator.
191
1
0.55 ... 0.74 rl
Measure the resistance between the specified points.
Q
Alternator, connector
CR
pin 1 (White) - Alternator, connector
CR
pin 1 (Yel-
low)
Chackillllha ilJlilion uba
~narator
Alternator
Light winding resistance at: 20°C 10.127 ... 0.172 rl
(68
OF)
• If the specification is not reached:
- Change the stator.
Condition
The crankshaft position sensor is disconnected.
Measure the resistance between the specified points.
AT
Q
Ignition pulse generator, connector
AT
pin 1 - Ignition pulse generator, con-
nector
AT
pin 2
Ignition pulse generator
Resistance at: 20°C (68
OF)
I
80 ... 120 rl
• If the specification is not reached:
- Replace the ignition pulse generator.
40058!>-l0
AT
400585-10
Measure the resistance between the specified points.
Ignition pulse generator, connector
AT
pin 1 - Measuring point
Ground (-)
1
Resistance
• If the specification is not reached:
- Replace the ignition pulse generator.
- Connect the special tool to the multimeter.
1
Peak voltage adapter (58429042000) (-- p. 256)
• Info
I
When using the peak voltage adapter, adjust the measuring range of the multi meter to DCV.
- Start the motorcycle for a check. (-- p. 11)
Check the ianition pulse lenerator voltage
AT
V
Measure the voltage between the specified points.
Ignition pulse generator, connector
AT
pin 1 - Ignition pulse generator, con-
nector
AT
pin 2
I
Ignition pulse generator
Voltage
12 ...
4 V
• If the specification is not reached:
40058~1O