System Diagnostic Options; System Configuration Interface - Status Page; Dgx_Shell Commands - AMX Enova DGX 100 Series Hardware Reference Manual

Enova DGX 100 Series and Enova DGX 8/16/32/64 Differences
Audio and EDID Functionality
EDID Read/Write Support
Audio Expansion Boards
NOTE:
Only one type of
Expansion Board can be used in
a given enclosure.
Audio Insert/Extract/Routing
down-mixing
Upgrades, Firmware Resets, and Default Restoration
Web Upgrade Status
Failed Upgrade Recovery
Factory Firmware Image Reset
Switcher
Factory Firmware Image Reset
Master and AxLink Controller
Restore system defaults
System Components
RJ-45 ports
External MicroSD Card
Internal MicroSD Card
ID Button
Integrated AxLink Control
Control Panel

System Diagnostic Options

The two system diagnostic options for the Enova DGX 100 Series are the Status page in the System Configuration interface
and DGX_SHELL commands.

System Configuration Interface - Status Page

The Status page in the System Configuration interface (Switcher/Status) displays status for the power supplies, fans, CPU,
I/O boards, and expansion boards (see page 141). For complete information, see the WebConsole & Programming Guide
– NetLinx NX Central Controllers at www.amx.com.

DGX_SHELL Commands

The Enova DGX 100 Series supports a number of shell (command-line interpreter) commands for a variety of functions,
both basic and advanced (see "Appendix C" on page 273).
Enova Digital Media Switchers - Hardware Reference Manual
Use DGX Configuration Software EDID
Programmer tab
Audio Insert/Extract (AIE) Boards Only
AIE - DIP settings tie insertion/extraction to
I/O channels.
No audio breakaway routing
Not Supported
Web Control Interface link to status page
http://Master_IP_Address/web/upgrade/
systemUpgradeStatus.xml
Rolls back to previous kit version
N/A
N/A
BCS command ( )
~def!
NOTE:
only resets MCPU
• Left: ENC & ENC
• Right: Public LAN
Contains system configuration, presets,
event logs, SRM file.
N/A
N/A
N/A
Basic control panel functions only.
Enova DGX 100 Series - Overview
Use System Configuration interface to change/save/
load EDID. Changes can be made to either Video or
Audio EDID or a Custom file loaded
• Audio Insert/Extract Boards (AIE)
• Audio Switching Boards (ASB)
NOTE:
ASB must be installed as a pair.
• AIE - DIP settings tie insertion/extraction to I/O
channels.
• ASB and ASB-DAN - Independent I/O channels for
audio switching, breakaway, and down-mix.
NOTE:
Switched audio also supports DSP functionality.
Outputs utilizing ASB audio must be set to SWITCHED
audio.
Audio Switching Boards support one down-mix channel
(the last audio input) which down-mixes any input
channel and can be routed to any output
System Configuration interface System/Devices page,
select the Switcher Update Status button
Completes the upgrade to attempted kit version and
identifies any mismatch in I/O cards that failed to
update.
This is shown in the OnLine Tree, the System
Configuration interface, and
DGX_SHELL> show
DGX_SHELL> manage firmware
Factory
ID Pushbutton on Master or Telnet to Master and type:
then select the device to reset
manage firmware
( or )
0 5001
DGX_SHELL command
(reset factory)
• resets whole system
• Left: ICSLAN (Private LAN - DHCP Server)
• Right: Public LAN
• Contains no files or data
• Only for file transfer to/from Internal SD Card
Contains sys configuration, event logs, SRM file, current/
previous/factory firmware, EDID Library
• Switch between DHCP and Static - 10 sec hold while
running
• Factory Reset (Master) - 10 sec hold on power up
• Factory Firmware Reset (Master) - 20 sec hold on
power up
AxLink port for control of AMX AxLink devices
Displays Integrated Master info and provides basic
audio support (for embedded audio only)
.
then select "F" for
33