Dxlink Endpoint Send_Commands; Endpoint_Tx_Icslan_Port; Endpoint_Rx_Icslan_Port; Netlinx Nx Master Telnet Commands - AMX Enova DGX 100 Series Hardware Reference Manual

DXLink Endpoint SEND_COMMANDs

IMPORTANT: The commands in this section affect endpoints, but are addressed to the input or output port connected to
the associated endpoint.
DXLink Endpoint SEND_COMMANDs
Command

?ENDPOINT_TX_ICSLAN_PORT

ENDPOINT_TX_ICSLAN_PORT

?ENDPOINT_RX_ICSLAN_PORT

ENDPOINT_RX_ICSLAN_PORT

NetLinx NX Master Telnet Commands

The table below contains Telnet commands which apply to the integrated NetLinx NX Master.
NOTE:
For further information about using Telnet commands and a complete list of commands available for NetLinx NX Central
Controllers, see the NX-Series Controllers WebConsole & Programming Guide at www.amx.com.
NetLinx NX Telnet Commands for the Integrated NetLinx NX Master
Command
AUTO LOCATE

(ENABLE|DISABLE|STATUS)

DOT1X

(ENABLE|DISABLE|STATUS)

MANAGE FIRMWARE

PROGRAM
(ENABLE|DISABLE|STATUS)
Enova Digital Media Switchers - Hardware Reference Manual
Description
Requests the IP configuration of the ICSLAN port on the DXLink TX.
Note: Does not apply to DXLink Wallplates.
Syntax:
SEND_COMMAND <DEV>, "'?ENDPOINT_TX_ICSLAN_PORT'"
Example:
SEND_COMMAND 5002:13:1, "'?ENDPOINT_TX_ICSLAN_PORT'"
Returns a COMMAND string of the form:
ENDPOINT_TX_ICSLAN_PORT-<PRIVATE|PUBLIC>
Changes the IP configuration of the ICSLAN port on the DXLink TX.
Note: Does not apply to DXLink Wallplates.
Syntax:
SEND_COMMAND <DEV>, "'ENDPOINT_TX_ICSLAN_PORT-<PRIVATE|PUBLIC>'"
Example:
SEND_COMMAND 5002:13:1, "'ENDPOINT_TX_ICSLAN_PORT-PRIVATE'"
Note: Default setting for DXLink endpoints is PUBLIC.
Requests the IP configuration of the ICSLAN port on the DXLink RX.
Syntax:
SEND_COMMAND <DEV>, "'?ENDPOINT_RX_ICSLAN_PORT'"
Example:
SEND_COMMAND 5002:14:1, "'?ENDPOINT_RX_ICSLAN_PORT'"
Returns a COMMAND string of the form:
ENDPOINT_RX_ICSLAN_PORT-<PRIVATE|PUBLIC>
Changes the IP configuration of the ICSLAN port on the DXLink RX.
Syntax:
SEND_COMMAND <DEV>, "'ENDPOINT_RX_ICSLAN_PORT-<PRIVATE|PUBLIC>'"
Example:
SEND_COMMAND 5002:14:1, "'ENDPOINT_RX_ICSLAN_PORT-PRIVATE'"
Note: Default setting for DXLink endpoints is PUBLIC.
Description
Enables/disables/queries the auto locate feature on the integrated Master. Auto locate adds additional
broadcast information for use by AMX Touch Panel devices configured in Auto connect mode.
Syntax:
Auto Locate [enable|disable|status]
Enables/disables 802.1x security or displays its current settings. The default settings is disable.
Syntax:
DOT1X[status|enable|disable]
Telnet interface to load previous and factory firmware versions for both the integrated Master (device 0)
and controller (device 5001).
Example:
>manage firmware
Devices
-------
0 - Master
5001
Select device or press return to cancel:0
Current Version: 1.2.259
Previous Version: 1.2.258
Factory Version: 1.2.250
To install a firmware version:
Enter P (Previous), F (Factory) or press return to cancel:
Enable/disable the NetLinx program or display the status of the current program execution setting.
The default setting is enable.
Note: For information on using this command, see page 79.
The setting (enable or disable) persists through power down and through firmware updates, etc., until a
new command is sent. If the software setting is disabled, then the NetLinx program is disabled.
Syntax:
PROGRAM [status|enable|disable]
Integrated Master - NetLinx Programming
232