Yamaha F150B Service Manual page 445

PTT cylinder..............................................9-50
PTT gear pump .........................................9-45
PTT motor .................................................9-39
PTT requirement .........................................1-5
PTT switch and cowling lock lever ..............9-6
PTT system.............................. 1-8, 1-17, 5-48
PTT unit ................................. 1-20, 2-29, 9-32
R.
Reducing the fuel pressure .........................6-4
Refacing the valve seat.............................7-41
Remote control box and switch panel
installation ...............................................3-16
Removing the anode (cylinder block)........7-48
Removing the clamp bracket ....................9-29
Removing the cowling lock lever.................9-8
Removing the crankcase cover.................7-48
Removing the cylinder head .....................7-38
Removing the drive shaft .................8-16, 8-61
Removing the exhaust cover ....................7-34
Removing the flushing hose........................9-8
Removing the flywheel magnet...................7-6
Removing the lower unit ....................8-3, 8-49
Removing the oil filter bracket...................7-48
Removing the oil pump assembly .............7-48
Removing the power unit ..........................7-22
Removing the propeller shaft housing
assembly........................................8-10, 8-55
Removing the PTT motor..........................9-41
Removing the PTT switch ...........................9-8
Removing the PTT unit .............................9-33
Removing the reservoir.............................9-41
Removing the shift rod and shift bracket.....9-3
Removing the starter motor ......................5-42
Removing the steering arm.......................9-24
Removing the tilt ram and trim ram...........9-52
Removing the timing belt, driven sprocket,
and camshaft ..........................................7-28
Removing the upper case .........................9-14
Removing the water pump and
shift rod ............................................8-6, 8-52
Removing the wiring harness......................7-8
Replacing the oil filter..............................10-11
Replacing the timing belt................7-18, 10-16
Replacing the valve guide.........................7-40
Reverse gear shim (T1) selection chart ....8-83
Reverse gear shim (T2) selection chart ....8-45
Rigging grommet description ......................3-8
Rigging recommendations ........................3-25
Rotating part ...............................................0-1
S.
Safety while working ...................................0-1
Sealant and locking agent .......................... 0-6
Selecting the connecting rod bearing ....... 7-57
Selecting the main bearing ....................... 7-60
Selecting the pinion shim (T3) ......... 8-33, 8-73
Selecting the propeller shaft shim (T4) ..... 8-73
Selection................................................... 3-26
Self-protection ............................................ 0-2
Sensor, switch and actuator ....................... 2-4
Serial number ............................................. 1-2
Shift rod and shift bracket........................... 9-1
Shim location ................................... 8-32, 8-72
Shimming......................................... 8-31, 8-71
Shimming (counter rotation model) .......... 8-65
Shimming (regular rotation model) ........... 8-25
Shimming check sheet .................... 8-26, 8-66
Shimming workflow.......................... 8-25, 8-65
Single outboard motor application ............ 3-21
Special service tool.............................. 0-3, 0-8
Special tightening torque .......................... 1-18
Starter motor.................................... 5-40, 7-12
Starting system ........................................... 1-9
Starting units and components ................. 5-38
Stationary condition .................................. 2-32
Steering arm ............................................. 9-23
Symbol........................................................ 0-6
Synchronizing the throttle valve................ 6-23
System diagram........................................ 3-21
T.
Test run .................................................... 10-7
Throttle body............................................. 6-20
Throttle link ............................................... 6-17
Tightening torque........................................ 0-3
Timing belt ................................................ 7-17
Top view .............................................. 5-5, 5-9
Trim ram retraction function...................... 2-30
Trim-down and tilt-down function.............. 2-31
Trim-up and tilt-up function....................... 2-29
Trouble code and checking step................. 4-6
Troubleshooting procedure......................... 4-4
Troubleshooting the lower unit ................. 4-18
Troubleshooting the power unit .................. 4-4
Troubleshooting the power unit (trouble code
not detected)........................................... 4-11
Troubleshooting the power unit using the
diagnostic flash indicator ........................ 4-10
Troubleshooting the power unit using
the YDIS ................................................... 4-4
Troubleshooting the PTT unit ................... 4-17
Twin outboard motor application .............. 3-23
U.
Uncrate procedure...................................... 3-5
Index
0
1
2
3
5
6
7
8
9
10
10
A
i-5