HP 6127xlg Configuration Manual page 464

[MCE-ospf-10] quit
# Display the routing table of VPN 1 on the MCE.
[MCE] display ip routing-table vpn-instance vpn1
Destinations : 13
Destination/Mask
0.0.0.0/32
10.214.10.0/24
10.214.10.0/32
10.214.10.3/32
10.214.10.255/32
127.0.0.0/8
127.0.0.0/32
127.0.0.1/32
127.255.255.255/32
192.168.0.0/24
224.0.0.0/4
224.0.0.0/24
255.255.255.255/32
The output shows that the MCE has learned the private route of VPN 1 through OSPF process 10.
# On the MCE, bind OSPF process 20 to VPN instance vpn2 to learn the routes of VPN 2. The
configuration procedure is similar to that for OSPF process 10.
The output shows that the MCE has learned the private route of VPN 2 through OSPF:
[MCE] display ip routing-table vpn-instance vpn2
Destinations : 13
Destination/Mask
0.0.0.0/32
10.214.20.0/24
10.214.20.0/32
10.214.20.3/32
10.214.20.255/32
127.0.0.0/8
127.0.0.0/32
127.0.0.1/32
127.255.255.255/32
192.168.10.0/24
224.0.0.0/4
224.0.0.0/24
255.255.255.255/32
3. Configure routing between the MCE and PE 1:
# Configure the ports between the MCE and PE 1 as trunk ports. The configuration procedure is
similar to that described in
# Enable BGP in AS 100 on the MCE.
[MCE] bgp 100
Routes : 13
Proto Pre Cost
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
OSPF 10 2
Direct 0 0
Direct 0 0
Direct 0 0
Routes : 13
Proto Pre Cost
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
OSPF 10 2
Direct 0 0
Direct 0 0
Direct 0 0
"Configure routing between the MCE and PE
455
NextHop Interface
127.0.0.1 InLoop0
10.214.10.3 Vlan10
10.214.10.3 Vlan10
127.0.0.1 InLoop0
10.214.10.3 Vlan10
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
10.214.10.2 Vlan10
0.0.0.0 NULL0
0.0.0.0 NULL0
127.0.0.1 InLoop0
NextHop Interface
127.0.0.1 InLoop0
10.214.20.3 Vlan20
10.214.20.3 Vlan20
127.0.0.1 InLoop0
10.214.20.3 Vlan20
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
10.214.20.2 Vlan20
0.0.0.0 NULL0
0.0.0.0 NULL0
127.0.0.1 InLoop0
1:." (Details not shown.)