Huawei HG8240 Service Manual page 161

EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
Issue 04 (2011-01-12)
huawei(config)#dba-profile add profile-id 20 type3 assure 15360 max
30720
(2) Configure an ONT line profile.
Create GPON ONT line profile 10 and bind T-CONT 2 to DBA profile 20.
huawei(config)#ont-lineprofile gpon profile-id 10
huawei(config-gpon-lineprofile-10)#tcont 2 dba-profile-id 20
Create GEM port 2 for carrying traffic streams of the ETH type and bind GEM
port 2 to T-CONT 2. Set the QoS mode to priority-queue (default).
NOTE
a. To change the QoS mode, run the qos-mode command to configure the QoS mode to gem-
car or flow-car, and run the gem add command to configure the ID of the traffic profile
bound to the GEM port.
b. When the QoS mode is PQ, the default queue priority is 0; when the QoS is flow-car,
traffic profile 6 is bound to the port by default (no rate limitation); when the QoS mode is
gem-car, traffic profile 6 is bound to the port by default (no rate limitation).
huawei(config-gpon-lineprofile-10)#gem add 2 eth tcont 2
Configure the mapping between the GEM port and the ONT-side service to the
VLAN mapping mode (default) and map the service port of CVLAN 20 to GEM
port 2.
huawei(config-gpon-lineprofile-10)#mapping-mode vlan
huawei(config-gpon-lineprofile-10)#gem mapping 2 1 vlan 20
After the configurations are complete, run the commit command to make the
configured parameters take effect.
huawei(config-gpon-lineprofile-10)#commit
huawei(config-gpon-lineprofile-10)#quit
(3) Configure an ONT service profile.
The service profile type must be the same as the actual ONT type. The HG8240
and HG8245 each have four ETH ports and two POTS ports. The HG8247 has
four ETH ports, two POTS ports, and one CATV port.
huawei(config)#ont-srvprofile gpon profile-id 10
huawei(config-gpon-srvprofile-10)#ont-port eth 4 pots 2
After the configurations are complete, run the commit command to make the
configured parameters take effect.
huawei(config-gpon-srvprofile-10)#commit
huawei(config-gpon-srvprofile-10)#quit
(4) (Optional) Configure an alarm profile.
– The ID of the default GPON alarm profile is 1. The thresholds of all the alarm
parameters in the default alarm profile are 0, which indicates that no alarm is
reported.
– In this example, the default alarm profile is used, and therefore the
configuration of the alarm profile is not required.
– Run the gpon alarm-profile add command to configure an alarm profile,
which is used for monitoring the performance of an activated ONT line.
5. Add an ONT on the OLT.
The ONT is connected to the GPON port of the OLT through optical fibers. The service
can be configured only after an ONT is successfully added on the OLT.
Two ONTs are connected to GPON port 0/1/1. The ONT IDs are 1 and 2, the SNs are
6877687714852900 and 6877687714852901, the management mode is OMCI, and
ONT line profile 10 and service profile 10 are bound to the two ONTs.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3 Configuration
3-123