Vermont Castings Radiance RADVTSCCB Installation And Operating Instructions Manual page 37

Radiance Direct Vent Gas Heater
®
SYSTEM CONFIGURATION/SETUP
All System configuration/setup is done on the Command
Center. Choose the mode that best suits your needs.
NOTE: When using On/Off wall switch, the switch
must be in the ON position to perform all configu-
ration set ups at the command center.
Cold Climate Option
The Signature Command System is designed to operate
in either Standing Pilot or Intermittent Pilot mode.
• The Standing Pilot Mode is best for colder climates
when the pilot must remain on continuously to prevent
condensation and ensure reliable operation.
• The Intermittent Pilot Mode is ideal for maximum effi-
ciency, igniting the pilot only when needed to start your
stove, lowering fuel consumption and reducing your
carbon footprint.
Either mode benefits from the instantaneous battery
back-up, so you never have to worry about a power outage.
NOTE: The Signature Command System comes
standard in the Intermittent Pilot mode, so you
must follow the instructions below to switch to
Standing Pilot Mode if needed.
Intermittent/Standing Pilot Setup (Default intermit-
tent)
Holding the ON button on the Command Center while
turning on the master switch will toggle between standing
pilot and intermittent pilot.
After the above operation, one beep (for standing pilot)
or two beeps (for intermittent pilot) will be given as con-
firmation.
Six-hour Safety Shutdown Option (Default ON)
The system comes preset from the factory with a six (6)
hour shutdown from its last command of operation. This
is done to prevent the stove from continuing to operate if
unattended. You may disable this feature if you wish.
NOTE: By disabling this feature, your stove may
continue to operate unattended.
Function
Intermittent/Standing
Pilot Setup
Standing Pilot Temp.
Shutoff
RF Remote Receiver
On/Off
Learn Remote
Transmitter
6-hour safety
shutdown setup
20306759
SIGNATURE COMMAND OPERATING INSTRUCTIONS
Hold the ON p button while turning on the master switch
(Beep once for standing pilot, twice for intermittent pilot)
Hold the ON p button 3 seconds (when the master switch
on the main burner is off)
Push the RF receiver On/Off button on the control board
Beep once for ON and beep twice for OFF
Hold the OFF q button while turning on the master switch
(Beep twice then press any handheld remote button)
Press the ON p button and OFF q button simultaneously
(Beep once for ON, twice for OFF)
When the master switch is in the ON position ("-"), pressing
the ON button and the OFF button on the Command Center
simultaneously will toggle between enabling and disabling
the six-hour shutdown option.
After the above operation, one beep (for enabling the
six-hour shutdown option) or two beeps (for disabling the
six-hour shutdown option) will be given as confirmation.
Remote Transmitter Learn Function (Default OFF)
The RF receiver button located on the Control Board must
be in the on position before the learn function can begin.
Use paper clip to depress button. One beep for RF receiver
ON or two beeps for RF receiver OFF will be given as
confirmation. Refer to Figure 57 for location.
After the RF receiver is on, holding the OFF button on the
Command Center while turning on the master switch will
activate the learn function for the transmitter.
After the above operation, two beeps will be given and
the green LED on the Command Center will flash for 10
seconds.
During the 10 seconds, press the OFF button on a trans-
mitter to learn. Another two beeps will be given to confirm
a successful learning. Refer to transmitter instructions for
remote operations.
Shutting Off the Standing Pilot (Temporary Shut Off)
To shut off the standing pilot for service or summer shut
down, press and hold the ON button on the Command
Center for 3 seconds when the master switch is in the ON
position ("-") and the main burner is off.
Note: Pilot will resume the next time system is turned on.
Key Combinations for System Settings
NOTE: When On/Off wall switch is used, it must be
in the On position to perform all system setups.
Operation Default Setting
Intermittent
Pilot
RF OFF
ON
37