Easy Menu Driven Program Mode; Dealer Program - Preliminary Information; Accessing Dealer Program Mode; Customizing A Default Program - NAPCO GEMINI GEM-P3200 Programming Instructions Manual

WI818G 10/05

EASY MENU DRIVEN PROGRAM MODE

DEALER PROGRAM - PRELIMINARY INFORMATION

Only Keypad #1 may be used for both dealer and user programming, however this keypad may be located in any area.
The Master Security Code is printed on the panel's microprocessor can. Use this code to enter the Dealer Program Mode
to program a custom Dealer Security Code. Record the number, then remove the code label to prevent unauthorized
access to the panel. If you forget your Dealer Security Code, use the Master Security Code to enter programming.
After entering codes or data, press the save
If the keypad is in the Program Mode and no activity is detected for longer than 4 minutes, a steady tone will sound.
Silence the sounder by pressing the
A panel that has been COLD STARTED (Address Location 4093) performs identically to a new panel.
If a GEM-RP2ASe2/GEM-K2AS (Version 6) is used, configure address jumpers as Keypad #1 (see WI1184).
KEYPAD #1: For ease of programming, it is recommended that a GEM-K1CA (Version 8) be used as Keypad #1.
(Regardless of which keypad is selected, all new keypads are configured as Keypad #1 out of the box).

ACCESSING DEALER PROGRAM MODE

1. Press EEEEEE
Q
2. Press Until "ACTIVATE PROGRAM Y/N" appears on the keypad display.
P
3. Press To Enter Dealer Program Mode.
4. Press CC To Exit Dealer Program Mode when finished.

CUSTOMIZING A DEFAULT PROGRAM

For new panels, you can design a default program that will best suit your application. Using this procedure, you will configure the panel for:
•
Total Number of Zones in Area 1
•
Total Number of Zones in Area 2
•
Fire Zones in Area 1
•
2-Wire Fire Zones in Area 1
•
Report All Zones to Central
•
Exit/Entry Zones in Area 1
•
Interior Zones in Area 1
•
24 Hour Zones in Area 1
•
Chime Zones in Area 1
•
Chime 2 Zones in Area 1
•
Exit/Entry2 Zones in Area 1
•
50mS Loop Response Zones
required for Loop Response time in UL installations).
This procedure will automatically set up system keypads, EZMs, wireless transmitters, etc. After your basic default program has been
loaded, you may alter it as necessary in the Direct Address Program Mode.
NEW PANELS: The custom default program may be created for new panels only. Once the panel has been programmed by any
means, the number of areas, number of zones, fire zones, entry/exit zones and interior zones will be suppressed and cannot be
changed. Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press the
button to enter the Direct Address Program Mode; (b) access Location 4091 (Clear Program); (c) press the
L
NAPCO Security Systems
U
button. Data will not be stored into memory unless it is pressed.
button to continue, or by pressing the
G
Master Security Code
(on microshield)
•
Aux Output Activated on Alarm Zones
•
Sensor Watch Zones
•
Keypad Sounder on Alarm Zones
•
Auto Bypass re-entry Zones
•
Enable no EOLR Zones
•
Enable Telco Line Fault Test
•
Enable Burg Output Chirp on Keyfob
•
Enable SIA CP-01 Features
•
Number of Keypads in Area 1
•
Number of Keypads in Area 2
•
Central Station Receiver 1 Tel. Number
•
Central Station Receiver 1 Account Number
(Note: 750mS is
button to exit.
C
R
•
Central Station Receiver 1 Format
•
Enter User Codes
•
RF Transmitter Points
•
Quick Method (Enroll Method)
•
KeyFob Transmitters (as Arm/Disarm & Control
Devices)
•
KeyFob Transmitters (as Zone Input Devices)
•
Enter Zone Descriptions
•
Enter Date
•
Enter Time
•
Dealer Code
•
Exit Dealer Program Mode
U
X
GEM-P3200 Programming Instructions
Page 5
GEM-P3200
CONTROL
R
COMMUNCIATOR
MASTER SECURITY CODE
# - # - # - # - # - #
C
button and start over.