NAPCO Gemini GEM-P3200 Installation Instructions Manual
Control panel/communicator
Hide thumbs
Also See for Gemini GEM-P3200:
- Programming instructions manual (76 pages) ,
- Installation instructions manual (68 pages) ,
- Addendum (2 pages)
Related Manuals for NAPCO Gemini GEM-P3200
Summary of Contents for NAPCO Gemini GEM-P3200
- Page 1 NEXT/YES PRIOR/NO AREA GEM-RP1CA/1CAe/1CAe2 Keypad NEXT/YES PRIOR/NO AREA GEM-RP2AS/RP2ASe/RP2ASe2 Keypad © Napco 1998 WI817B 11/98...
- Page 2 NAPCO Security Systems, Inc. 333 Bayview Avenue, Amityville, New York 11701 For Sales and Repairs, call toll free: (800) 645-9445 For direct line to Technical Service, call toll free: (800) 645-9440 Internet: http://www.napcosecurity.com...
-
Page 3: Table Of Contents
EXPERIENCE AND INSTALLATION EQUIPMENT. THE UNIT IS DESIGNED TO BE PROGRAMMED USING AN IBM-COMPATIBLE COMPUTER WITH NAPCO PCD3000 SOFTWARE. AFTER PROGRAMMING, BE SURE TO RUN THE PCD3000 ERROR-CHECK UTILITY TO GUARD AGAINST PROGRAMMING CONFLICTS FOR THE TYPE OF SERVICE SELECTED FOR THE INSTALLATION. - Page 4 Conventional LEDs and a sounder are also provided for annunciation. Data may be quickly and easily downloaded to the control panel using a PC-compatible computer with Napco's PCD3000 Quickloader software and PCI2000 computer interface. Or, the panel may be programmed using the keypad in its secondary mode of operation.
- Page 5 Access only capability. Provisions for fire, police and auxiliary panic alarms. Integral 4-zone EZM included in each keypad (GEM-RP1CA/RP1CAe/RP1CAe2 only). Communicator Test to Central facilitates testing; Locate, Fault-Find and EZM-Locate diagnostics simplify troubleshooting. PGM output. NAPCO Security Systems GEM-P3200 Installation Instructions...
-
Page 6: System Components
GEM-P3200: Residential UL-Listed Burg Control Panel. GEM-P3200M: Mercantile UL-Listed Burg and Fire Control Panel. GEM-RP1CA\RP1CAe\RP1CAe2: 32-Character LCD Burg & Residential Fire Keypad with 4 EOL Zones. GEM-RP2AS\RP2ASe\RP2ASe2: LCD Burg & Residential Fire Keypad with remote panic. NAPCO Security Systems GEM-P3200 Installation Instructions... - Page 7 Central Station Burglar Alarm Units: UL1610 Smoke Detectors, 2-Wire: Police Station Alarm Units: UL365 System Sensor 1400; 2400; 2400TH, each with self- contained base; 1451; 2451; 2451TH, each with B401B Base Voltage Rating: 8.5-13.3Vdc Maximum Number of Detectors: 10 NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 8 System must be serviced at least once every 3 years Residential Fire and Combination Residential Fire & Burglary must program “Residential Fire” Keypad Expansion (EZM) Zones are not to be used as fire zones NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 9 24-Hour Zone or Day Zone. When used on a normally-open zone, normally-closed tamper switches (open when set) should be wired in parallel. On a normally-closed zone, install Napco TPS-2 normally-open tamper switches (closed when set) in series.
- Page 10 Note: NFPA 74 (Household Fire Warning Equipment) requires that a fire alarm audible device be installed indoors. The User Program Code is not to be given to anyone except the authority responsible for all partitions. NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 11 In addition to Grade-B Requirements (above), one relay on the RM3008 must be programmed to trip the Ademco 7720 when the telephone line fails. Daily openings and closings are required to be transmitted by the Napco panel along with the 24-hour DACT test signal and DACT trouble conditions.
- Page 12 The last received signal strength for each transmission is always stored in memory and can viewed at any time using this procedure. Signal strength can also be viewed through the PCD3000 Status Screen. NAPCO Security Systems GEM-P3200 Installation Instructions...
-
Page 13: Specifications
GEM-P3200 Programming Instructions). Connect the device controlled by the programmable output between terminal 8 (+) and terminal 14 (-). A programming option “Aux. Output Chirp on Key-fob Arming” is available. If selected, an external siren driver can be connected to these terminals. NAPCO Security Systems GEM-P3200 Installation Instructions... - Page 14 Auxiliary Power provides a filtered 12 VDC nominal output which is used for powering auxiliary AUX POWER devices. NOTE: To calculate the available standby time refer to the Standby-Battery Calculation Worksheet at the back of this manual. NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 15 Wireless zone expanders include: GEM-RECV8 (8 additional zones per receiver), GEM-RECV16 (16 additional zones per receiver) and GEM-RECV96 (32 additional zones per receiver). Wireless transmitters include: GEM-TRANS2, GEM-TRANS4, GEM-KEYF, GEM-SMK, GEM-PIR, GEM-DT and GEM-GB. NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 16 Instructions) and set JP7 to the position as shown. Connect the 2-wire smoke detectors as shown. If Fire Alarm Verification is desired to reset the smoke detectors, select this option for the desired fire zone (zone 7 or 8). NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 17 If connected to a line with call waiting, then call waiting interrupt numbers must be programmed into the CS Telephone Numbers (refer to the GEM-P3200 Programming Instructions). NAPCO Security Systems GEM-P3200 Installation Instructions...
-
Page 18: Keypad Address
A valid number will be acknowledged by a short beep; an invalid number will be rejected by a long beep. 2. Press the button to continue or press the button to exit. NAPCO Security Systems GEM-P3200 Installation Instructions... - Page 19 Keypad Configuration Mode “ ” “ ” (display will read “ ”). Then replace Jumper JP5 across Pins 1–2 (top two). “ ” NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 20 Cut Jumper B to disable LCD backlighting. DISABLE SOUNDER Cut Jumper C to disable the sounder. (Do not disable in UL applications.) NAPCO Security Systems, Inc. 333 Bayview Avenue, Amityville, New York 11701 For Sales and Repairs, call toll free: (800) 645-9445 For direct line to Technical Service, call toll free: (800) 645-9440 Internet: http://www.napcosecurity.com...
- Page 21 Thus should it become necessary to remove a user from the system, that one code may be cancelled without affecting other codes, and that user would then be prevented from entry. NOTE: Napco's PCD3000 Quickloader Software provides enabling and disabling User Codes at programmed times using the scheduling menus.
-
Page 22: Ambush Code
The display will read “ ” while the control panel communicates to the central station. If the ringback tone does not sound within about 30 seconds, the START EXIT TIME function may be used to manually start exit delay. NAPCO Security Systems GEM-P3200 Installation Instructions... - Page 23 As in Overview, if any zone is not secured, the area will not arm and the keypad will display “ # ”, where “#” represents the area number. To disarm both areas, press and enter a valid user code. To arm the alternate area, see Keypad Area Change. NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 24 Should a burglary alarm occur, the red ARMED LED will flash, and the display will alternately read “ ”, then the zones violated. Disarm the panel; the display will read “ ” and will continue to indicate the violated zones until the button is pressed or the panel is armed once again. NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 25 DISPLAY PHONE #'S The panel can function as an autodialer to any of four programmed telephone numbers. (Telephone numbers must be programmed through Napco PCD3000 Quickloader software.) Select Telephone #1-4 using NEXT ( ) and PRIOR ) buttons, then press the button.
- Page 26 Correct the problem, then press the DISPLAY OP/CL Napco's PCD3000 Quickloader software offers a comprehensive array of programmable opening and closing suppres- sion windows, by area, for all days of the week, for both normal and holiday schedules. A two-line display of the programmed schedule may be read at the keypad.
-
Page 27: Wireless Systems
Displays most recent system events. Line 1 displays event and date. Line 2 displays time and other pertinent information, where necessary, depending upon event. To check previous system events, scroll back using the PRIOR ( ) button. NAPCO Security Systems GEM-P3200 Installation Instructions... -
Page 28: Battery
$ transmission not yet received $ transmitter's zone normal; $ transmitter's zone open; # $ transmitter battery low; $ transmitter case open; % $ supervisory failure (test transmission not received within programmed time); NAPCO Security Systems GEM-P3200 Installation Instructions... - Page 29 24 available external relays. The group number will display with a related description. Scroll through the groups using the NEXT ( ) and PRIOR ( ) buttons; change the status of the displayed group by pressing the button. NAPCO Security Systems GEM-P3200 Installation Instructions...
-
Page 30: Transformer
NN = transmitter number. LOCATE - Locate Mode activated. E05-NN - WL LOBATT. Rf transmitter low battery. NN = transmitter number. E06-NN - RF REC TROUBLE. Rf receiver response trouble. NN = receiver number. NAPCO Security Systems GEM-P3200 Installation Instructions... - Page 31 440Hz is received prior to dialing the access number. If the communicator must delay before dialing the access number instead of attempting to recognize the dial tone, find out how many 4-second delays must be programmed. Alarm on Day Zone See Day Zone NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 32 16-second anti-jam interval in order to free the telephone circuit from an incoming call, then make another 12-second attempt at dial-tone detection. If still unsuccessful, the communicator will again go off line for 16 seconds, then proceed to dial anyway. NAPCO Security Systems GEM-P3200 Installation Instructions...
-
Page 33: Auxiliary Alarm Output
Telephone 2. Also program Backup Report on Telco 2. Any zone programmed to report to Telco 1 will backup report to Telco 2. Note: Subscriber Identification Numbers for both Telephones 1 and 2 must be entered, even if they are the same. NAPCO Security Systems GEM-P3200 Installation Instructions... - Page 34 Lug E10 (BURG.) will go to about 1Vdc when the Burglary Output is tripped. This lug is intended for connection to UL-listed devices rated 5mA maximum and capable of operating over the voltage range of 8-13.0Vdc (12V, special application). Use Napco Part No.
- Page 35 Program Zone Type as follows: Fire* = “1” (Note: Not for Modem 2 Receivers); Panic = “2”; Burglary = “3”; Holdup = “4”; Gas Alarm = “7”; Heat Alarm = “8”; Auxiliary Alarm = “A” (Keypad displays “0”); 24-Hour Aux. Alarm = “B”. NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 36 Arming and disarming will turn off the Watch Mode. If Report Trouble is selected, a trouble on a Day Zone will be reported only when the Watch Mode is on. Dealer Security Code See Master Security Code NAPCO Security Systems GEM-P3200 Installation Instructions...
-
Page 37: Reset Output
Causes data transmission to start immediately after the telephone number. Disable Wait-for-Silence (Pager Format) Causes data transmission to start immediately after the pager telephone number. Double Reporting See Report Telco 3 Download Security Code See Master Security Code NAPCO Security Systems GEM-P3200 Installation Instructions... - Page 38 E9 - See Fire Lug E10 - See Burglary Lug E19 - See Veri-Phone: Silence All Outputs During Audio Session E22 - Common terminal for Reset Relay. Use Napco Part No. WL1 for field wiring. Easy Arming Permits quick arming by simply pressing the button.
-
Page 39: Wire Smoke Detectors
Lug E9 (FIRE) will go to about 1Vdc when a Fire Zone programmed for Fire Output is tripped. This lug may be used for auxiliary equipment. (For use, refer to the instructions furnished with the device.) Use Napco Part No. WL1 for connection. - Page 40 The Auxiliary Relay can be programmed to activate for a programmable period of time. This allows it to be used for access functions such as opening and closing a garage door. This is achieved through a new KeyFob option, Access control, NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 41 4. Enter the zone #. The display will read, “ ” 5. To bypass another zone, repeat steps 3 and 4. To Security Unbypass a zone, follow the same procedure. When the zone # is entered (step 4), the display will read NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 42 This feature is suggested for use as a garage-door or driveway monitor, or similar application. No EOL Resistor Program for any zone not wired with a 2200W end-of-line resistor (Napco Part No. EOL2.2K). This will disable any zone-short NAPCO Security Systems...
- Page 43 The problem on a Priority Zone must be corrected before the panel can be armed. Any zone may be selected as a Priority Zone. A zone in trouble that is neither a Priority Zone nor an Auto-Bypass Zone will cause NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 44 3rd Location (XXX3): Enter an Event ID Code. A list of Event ID Codes is provided in the Programming Manual. 4th Location (XXX4): Left nibble, program (a) Zone Type and (b) Timeout Units as follows. NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 45 Program the Sensor-Watch PIR timer in Location 4088. Select a value in accordance with the anticipated activity within the coverage area while disarmed. In calculating the Sensor-Watch time, note that only the disarmed hours (the time between armed NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 46 When a closing report is successfully received, the central station will acknowledge by returning a kissoff signal. When the kissoff is received by the communicator, a 2-second ringback tone will sound at the keypad. Start Exit Delay After Ringback will cause the NAPCO Security Systems GEM-P3200 Installation Instructions...
-
Page 47: Telephone Lines
Telemetry Trouble system trouble will result. On the PCD3000 System Features screen, enable Telemetry Trouble: = XT to report on alarm or activate and output. On the PCD3000 System Reporting Codes screen, program a reporting code for Telemetry Trouble. &'! Keypad readout will be: NAPCO Security Systems GEM-P3200 Installation Instructions... - Page 48 Cancel Next Test Timer Report on Any Report The test timer schedule is programmed using Napco's PCD3000 Quickloader Software. If Test Timer is programmed, an automatic test report will be transmitted to the central station on the scheduled day(s) at the scheduled time. (UL installations require a report at least every 24 hours.) To report test timer, select Report Test Timer and program a report code.
- Page 49 TouchTone and rotary dial to reach Telephone 1, then Telephone 2. See Backup Report on Telco 2. Transmit “402” Closing Code Program to send a “402” closing code (for Ademco Point ID modem format) in place of a “401” code. NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 50 Trouble on Night Open, which will identify an open circuit on a normally-closed zone while armed as a trouble condition (not an alarm), is intended for use with a Napco Monitor-Series dual-technology sensor. While there will be no indication at the keypad, any of these trouble conditions can be reported if Report Trouble is programmed as well.
- Page 51 LED will go out if the zone is tripped. Note: The zone description will display on the LCD, therefore do not program a “panic” message for Panic Zones. Note: Do not program a Day Zone as a 24-Hour Zone. NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 52 Page 52 WI817B 11/98 NOTES NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 53 (Box 3) Alarm current drawn in alarm. Alarm Time in Hours. Example: For a 15 minute alarm timeout, Alarm Time = 15/60 = 0.25. MINIMUM REQUIRED BATTERY CAPACITY = BOX 2 + BOX 3 NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 54 Should removal of the circuit board be necessary, use this wiring legend to relocate wire leads to their proper terminals. Enter wire identification number or color code in WIRE NUMBER column and enter wire function in DESCRIPTION column (optional). TERMINAL WIRE NO. DESCRIPTION NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 55 Requires dealer code Not avialable in GEM-RP2AS/RP2ASe/RP2ASe2 keypads Initial Configuration only; suppressed thereafter NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 56 Minimum level required to access function Level 3 code with appropriate option Requires dealer code Not avialable in GEM-RP2AS/RP2ASe/RP2ASe2 keypads Initial Configuration only; suppressed thereafter NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 57 &*( (at any time) DIRECT ADDRESS PROGRAM MODE Minimum level required to access function Level 3 code with appropriate option Requires dealer code Not avialable in GEM-RP2AS/RP2ASe/RP2ASe2 keypads Initial Configuration only; suppressed thereafter NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 58 Press button (at any time) Minimum level required to access function Level 3 code with appropriate option Requires dealer code Not avialable in GEM-RP2AS/RP2ASe/RP2ASe2 keypads Initial Configuration only; suppressed thereafter NAPCO Security Systems GEM-P3200 Installation Instructions...
-
Page 59: Keypad Configuration Mode
(“ ”) * JP5 is located at the top-right corner of the circuit board. ** If a Compatability Number other than “0000” is programmed, “ % ” is displayed. NAPCO Security Systems GEM-P3200 Installation Instructions... - Page 60 Page 60 WI817B 11/98 NOTES NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 61 WI817B 11/98 Page 61 NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 62 Page 62 WI817B 11/98 NOTES NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 63 NAPCO Security Systems GEM-P3200 Installation Instructions...
- Page 64 NAPCO LIMITED WARRANTY NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants In no event shall NAPCO be liable for an amount in excess its products to be free from manufacturing defects in of NAPCO's original selling price of the product, for any...