NAPCO GEMINI GEM-P3200 Programming Instructions Manual page 14

Page 14
KeyFob Transmitters as Zone Input Devices
(Refer to display above: press the PRIOR button to go backwards).
Each of the 4 keyfob buttons can be assigned to a zone. For example, On button = point 1; Off button = point
2; A1 = point 3; A2 = point 4. Up to 48 keyfobs (using 1 button) or 24 keyfobs (using 2 buttons) or 14 keyfobs
(using all 4 buttons) or any combination up to a maximum of 48 controlled zones can be assigned, providing
multiple wireless panic buttons on a system, each reporting to a Central Station or a pager and/or annunciating
on a keypad the keyfob zone number with a description. To assign a keyfob to a zone: program the keyfob as
you would a transmitter, entering the keyfob's ID code, check sum and point number at the appropriate zone.
The "Quick Method" is not allowed. The zone may be hardwired to an electrical sensor as well as assigned to
a keyfob (either one will activate the zone alarm output). NOTE: If assigning a keyfob to a zone, the "ON/OFF"
buttons on the keyfob will no longer arm/disarm the system. The keyfob is converted to a "panic only" device.
0 0 1 -
(Direct Entry)
•
To proceed to the next description, place the cursor under the Zone Number (e.g. "01") and change the Zone
Number using 3 and 6. Program new description as above.
•
NOTE: Zone Descriptions can only be entered through the GEM-RP1CAe2 Keypad or by using the Napco Quickloader Software. See Easy
Menu Programming Worksheet for available zone description characters.
Enter Date
( / / )
(Direct Entry)
Enter Time
( : )
(Direct Entry)
D e a l e r C o d e
4 5 6 7 8 9
D E A L E R C O D E
R E - E N T E R
EXIT DEALER PROGRAM MODE: This completes the custom default program. Press
Mode for further programming or press
CLEAR PROGRAM:
Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press
the Address Program Mode; (b) access Location 4091 (Clear Program) or 4093 (Cold Start); (c) press
4 0 9 1 X X
4 0 9 3 X X
X
GEM-P3200 Programming Instructions
Enter Zone Descriptions
•
Press 1 and 2 to place the cursor and; press
3 and 6 to select the character.
•
For each zone, enter a description of up to two lines.
U
•
Press to save each description.
Enter Date (Press
R
•
Enter the current date in the format MM/DD/YY. (MM = month, DD = day and YY = year.
U
•
Press to save. Press the NEXT/YES button to proceed.
Enter Time (Press
R
•
Enter the current time in format HH:MMA/P, where HH=hours (01–12); MM=minutes (00–59).
•
Select AM or PM by pressing any number button to toggle selection.
U
•
Press to save. Press the NEXT/YES button to proceed.
Dealer Code
•
Directly enter the Dealer Code (default = 456789), using 0 through 9 buttons.
U
•
Press to save.
•
Re-enter the Dealer Code to verify the previous code.
U
•
Press to save.
•
Press the NEXT/YES button to proceed.
once again to end all programming and resume normal keypad operation.
C
Dealer Program Mode. A "SYSTEM TROUBLE/E09-00 SERVICE" will occur. Press
Clear Dealer Program (Erases Dealer Program)
Use this feature to erase the Panel Program, while maintaining Scheduled Data and Zone Descriptions. Access
H
address 4091 and press
to reprogram system.
Cold Start (Erases Entire Program)
H
This erases all programmed data (Dealer Program, Zone Description Data and Schedules). Access ad-
U
dress 4093 and press
grammed again with the Downloading Software.
to set cursor).
to set cursor.)
C
U
. Data entry is not allowed. NOTE: Enter Easy Menu Driven Program Mode
. Data entry is not allowed. NOTE: Some features (schedules) can only be pro-
WI818G 10/05
DATA AUX 1/AUX 2 OPTIONS
ENTRY
0
1 Relay Group 1 Toggle
2 Relay Group 2 Toggle
9 Panic
A Auxiliary
B Instant
C Aux. Output Toggle
D Access on Aux. Output
E Arm STAY ("K Series"
Keypads Only)
F Interior Bypass
("Classic" RP Series
to enter the Direct Address Program
C
U
and then (d) press C
to silence the keypad.
C
L
NAPCO Security Systems
None
to enter
to exit the