NAPCO GEMINI GEM-P3200 Programming Instructions Manual page 13

WI818G 10/05
Z N # X M I T # + C S P
Z n 0 1 - 0 0 0 0 0 0 : 0 - 0
Zone # Xmitter Check
Mapped to ID Sum
NOTE: When programming the ID Code number, "0" through "9" = 0 through 9; A = G0 ; B = G1 ; C =
G2 ; D = G3 ; E = G4 and "F" = G5.
Quick Method (Enroll Method).
Z N # X M I T # + C S P
Z n 0 1 - 0 0 0 0 0 0 : 0 - 0
Z N # X M I T # + C S P
Z N 0 1 - E N R O L L : A - -
Example. A 2-point transmitter has the RF ID number 287613:1. Map point
1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone "06".
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that one point
has been programmed. (Transmitter 287613:1, point 1 will be mapped
KEYFOB ZONE ASSIGNMENT: Keyfobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm sys-
tem, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the keyfob,
the location where the person holding the keyfob is stationed, or the special purpose of the keyfob button being depressed. See the
next page on Keyfob Transmitters as Zone Input Devices .
K F A X M I T # + C S O P
0 1 - 0 0 0 0 0 0 0 : 0 0 0
KF Area Xmitter Check
# ID Sum
NOTE: When programming the ID Code number, "0" through "9" = 0 through 9 ; A = G0 ; B = G1 ;
C = G2 ; D = G3 ; E = G4 and "F" = G5.
L
NAPCO Security Systems
RF Transmitter Points (Press
For each transmitter enter: (For wireless systems only. Also see Quick Method, which follows)
•
The zone number (01–48) to which the transmitter will be mapped.
Point
•
The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
#
•
The point number (1–2); enter "9" for unsupervised (all points).
U
•
Press to save and NEXT/YES button to proceed when all transmitters have been entered.
If a receiver is already installed in the panel, transmitter wireless points can be programmed automatically
("enrolled") using the following procedure. NOTE: The transmitter point will be enrolled only if the signal
strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be mapped.
2. Press to enter the Enroll Mode. The red and green LEDs on the keypad will
B
flash and the window will display as shown at left.
3. Open the loop of the point that is to be programmed (GEM-TRANS2 only).
4. Install the transmitter battery. The keypad will beep to indicate that the point has been
successfully enrolled. Multi-point transmitters can be mapped to successive zones
simultaneously.
Keyfob Transmitters as Arm/Disarm & Control Devices (Press
Keyfobs can be programmed as "Arm/Disarm" devices using their On/Off buttons (refer to WI752).
For each Keyfob Transmitter, enter:
•
The Keyfob Transmitter number (01–08).
Aux
•
1&2
The area number to which transmitter is assigned (0 to disable keyfob, 1 or 2).
•
The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
•
The Aux 1 Option (see keyfob aux 1 & aux 2 options).
•
The Aux 2 Option (see keyfob aux 1 & aux 2 options).
•
NOTE: Keyfobs 1-8 report openings and closings as Users 25-32.
U
•
Press to save and NEXT/YES button to proceed when all keyfobs have been entered.
to set cursor.)
R
to Zone 6).
5. Enter Zone "09".
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad will beep
once to indicate that one point has been programmed. (Transmitter
287613:1, point 2 is mapped to Zone 9).
X
GEM-P3200 Programming Instructions
Page 13
to set cursor).
R