Download
Share
Print this page
NAPCO Gemini GEM-P400 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. NAPCO Manuals
  4. Control Panel
  5. GEM-P400
  6. Installation instructions manual
NAPCO Gemini GEM-P400 Installation Instructions Manual

NAPCO Gemini GEM-P400 Installation Instructions Manual

Control panel/communicator
Hide thumbs Also See for Gemini GEM-P400:

Advertisement

Quick Links

Download this manual See also: User Manual
®
GEM-P400
Control Panel/Communicator

Installation Instructions

© NAPCO 1997
WI879A 8/97
Wi879a
Tuesday, September 16, 1997 08:16
page 1

Advertisement

loading

Related Manuals for NAPCO Gemini GEM-P400

Summary of Contents for NAPCO Gemini GEM-P400

  • Page 1: Installation Instructions

    ® GEM-P400 Control Panel/Communicator Installation Instructions © NAPCO 1997 WI879A 8/97 Wi879a Tuesday, September 16, 1997 08:16 page 1...
  • Page 2 User 4 code as an Ambush code. Wireless Ready Ordering Information ........4 Bell Supervision Optional Accessories........4 The GEM-P400 is wireless ready. When used with a Programming the Panel........5 Line Cut Detection GEM-RECV-XP8 receiver, the control panel can sup- Installation............6 port up to 4 wireless zones and 2 Keyfobs.
  • Page 3 Maximum Charging Current: -------165 mA Housing Dimensions : -------------- 11" x 8 " x 3" Maximum Input Current: -------------2.58 A (26.2x21.3x7.6) HxWxD Shipping Weight: -------------------- GEM-P400/4 15.5 lbs. Operating Temperature: ------------ 0-49ºC (32-120°F) Wi879a Tuesday, September 16, 1997 08:16 page 3...
  • Page 4 WI879A GEM-P400 Installation Instructions GEM-RECV-XP8: *Wireless Receiver UL HOUSEHOLD BURGLARY WARNING SYSTEM CONTROL UNIT GEM-TRANS2 Window/Door Transmitter STANDARDS # 1023, 985 GEM-KEYF: Keyfob Transmitter GEM-PIR: Wireless PIR VERIFIED TO COMPLY WITH F.C.C. PART 15 AS CLASS B : DIGITAL DEVICE...
  • Page 5 3. Connect terminal 15 (PGM) to terminal 3. attempting to report. +PWR GREEN RING RING 4. Apply power to the GEM-P400 control panel. TELCO PHONE 5. After a few seconds the ARMED, READY and SYSTEM TROUBLE LEDs will flash. GREEN 6.
  • Page 6 WI879A GEM-P400 Installation Instructions Zone Doubling Resistor for the primary zone and a Z (3.9 K) type Zone Doubling Resistor for the Grounding the Panel secondary zone. Mounting the Panel Connect the control-panel EARTH GROUND Mount the Panel close to an unswitched AC screw to a metal cold-water pipe.
  • Page 7 PGM Wiring ZONE LED DEFINITION SECOND STEADY TONE The PGM is a switched negative output that is Faulted Zone Incorrect Code Entered activated depending on the programming op- Bypassed Zone Slow Flash Invalid key entry tion(s) that have been selected [08], [23] - [25]. Zone in Alarm Flashing Connect the device controlled by the PGM be-...
  • Page 8 WI879A GEM-P400 Installation Instructions flash. The Ready and SYSTEM TRBL LEDs Arming/Disarming with a Keyfob Arming/Disarming with a Keyswitch The system can be armed/disarmed by using a The system can be armed by pressing the are out indicating: momentary Keyswitch wired to Zone 4.
  • Page 9 ARMED, the bypassed zones will only be dis- Full Setting the System with Automatic played if the Display Bypassed [21-3] option Bypassing - Home/Away with Delay To prevent the loss of the User 1 Code, the panel has been selected. Zones default program includes User 1 Code Lockout [96-2].
  • Page 10 WI879A GEM-P400 Installation Instructions The keypad ARMED LED will flicker rapidly. Zone LED Meaning Faulting a Exit/Entry Zone will result in an imme- diate alarm. User Arm/Disarm Code not programmed User Commands Chime ON/OFF User Arm/Code is currently being programmed...
  • Page 11 to 10, with 4 being marginal and 10 being excellent. Download (Programming Re- [00]Exit/Entry Zones The keypad will beep out a number, from 1-4, Delay allows exit and entry through an Exit/ quired) corresponding to the signal strength of the Entry Zone after the system is armed with- Establish a connection between the PCD phone transmitter.
  • Page 12 WI879A GEM-P400 Installation Instructions lay, also program zones as Exit/Entry Fol- Auto Interior Bypassing - Also program [06]Open Circuit Zones lower Zones [02]. zones as Home/Away with Delay Zone(s) Program this zone type if unsupervised nor- To return protection to zones of this type,...
  • Page 13 does not receive any signal (either a trip or a [08]PGM Output canceled by pressing before or after status) from a transmitter in the time speci- Enables the PGM Output on a zone trip for arming. fied, a system trouble ‘RF Supervisory Fail- each zone selected.
  • Page 14 WI879A GEM-P400 Installation Instructions Program User 4 Arm/Disarm Code. (2) Easy Exit/Easy Arm - Enables (2) Access Output - Activates the PGM Select reporting to Telco 1 [36-2] or Telco 3 command. While the system is output for 5 seconds using the [56-2].
  • Page 15 not required for Telco 1, Telco 2 and Telco 3. (3) Panic - Program to activate the PGM on (2) Reserved. If dial tone detection is not desired select No a Panic alarm. (3) Inhibit Fail-to-Communicate Display - (4) Test Timer - Program to activate the Dial Tone Detection in Communicator Fea- This option prevents the keypad from either PGM during a Test Timer report.
  • Page 16 WI879A GEM-P400 Installation Instructions (3) Single Digit - 3/1 Format. 3-digit Sub- [33]/[53] - Select Pager Extend  scriber ID number and a 1-digit Alarm Code [41] - D D D X X X X X X X C 0 will be transmitted.
  • Page 17 (4) Test Timer - Program to activate a Test [39]Opening/Closing Report, Telco 1 [42]Receiver Format (Telco 2) Timer report. Select users required to send opening and Select the format that will be used to report closing reports to Telephone Number 1. for Telco 2 (Backup reporting).
  • Page 18 WI879A GEM-P400 Installation Instructions time of arming send this code along with the digit is the zone number of the reporting [46]Communicator Features 2 zone number of the bypassed zone(s). For zone. For example, if zone 2 has a report...
  • Page 19 Up to two receivers can be wired to the (1) Opening After Alarm (Cancel Code) - The Signal strength of a transmitter can be GEM-P400. Each wireless transmitter can When enabled, all users that are not se- checked at the keypad (see Fault be mapped to a zone.
  • Page 20 WI879A GEM-P400 Installation Instructions Enter the RF ID# and AUX 1 and AUX 2 [71-74] Wireless Transmitters 3 Bell ON options for each Keyfob. Program a 3 in the AUX 1 and/or AUX 2 Enter the RF ID# and the point number that option to turn the Bell ON when the is to be mapped to the zone.
  • Page 21 8 Interior PCPreset Count [91]. Program an 8 in the AUX 1 and/or AUX 2 1. Create the GEM-P400 account to be (2) Answering Machine Override - Using option to Bypass Exit/Entry Follower Zones downloaded using PCD3000 Quick- the downloading computer, call the panel.
  • Page 22 WI879A GEM-P400 Installation Instructions Site [95]User 1 Code (3) System Trouble Auto Restore - Nor- At the site perform the following three steps: mally, System troubles require acknowledg- The 1st User code is a program code as 1. Arm the panel.
  • Page 23 EXAMPLE Audible System Trouble Indication - For all LOW BATTERY SYSTEM TROUBLE DISPLAY system troubles, except when the only system Enter to enter System Trouble mode Use the System Trouble chart on the following trouble is the loss of AC, the keypad will beep and determine the specific trouble.
  • Page 24 WI879A GEM-P400 Installation Instructions Keypad Beeps or Zone LED System Trouble Cause/Action Condition SYSTEM Flashes 1 Beep This trouble will occur if AC power is not present. Ensure that the transformer is connected to an unswitched power source. AC Power Failure If there has been a recent power failure, the battery may be partially depleted and must be recharged by the control panel.
  • Page 25 Zones programmed as Exit/Entry 6. The PGM Output Pulses in Alarm. Followers When the PGM lug of the control panel is 2. Zones programmed for 24 Hour Pro- programmed for an Armed indication it also 1. The bell output drops to about 3 volts in tection.
  • Page 26 WI879A GEM-P400 Installation Instructions 12. No Keypad Chime? 8. How do I remove Keypad Sounder on 10. Keypad LEDs Flicker. The keypad sounder is turned off with the Alarm? The Keypad is not receiving a POLL from The keypad sounder follows the Burg Out- the Panel.
  • Page 27 GEM-P400 WIRING DIAGRAM (REFER TO INSTALLATION INSTRUCTIONS WI879A) RECHARGEABLE BATTERY 12 VDC 4AH OR 7AH RESIDENTIAL BURG (4 HOUR STANDBY) BLACK COMBINED STANDBY = 350 mA BELL = 2.0 AMP ALL OUTPUTS ARE CURRENT LIMITED COLD WATER GROUND CONNECTION NOT USED...
  • Page 28 NAPCO neither assumes, nor authorizes any other person purporting to act on its behalf to modify, to change, or to assume for it, any other warranty or liability concerning its products. In no event shall NAPCO be liable for an amount in excess of NAPCO's original selling price of the product, for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any failure of the product.