Toshiba e-STUDIO2330C Service Manual page 1243

Ver.01
Page
- GENERAL PRECAUTIONS
The weight of the equipment has been corrected from "approximately 120 kg (264.55 lb.)"
to "approximately 121 kg (266.75 lb.) or 123 kg (271.16 lb.)".
2-2 2.1.1 General
The version name of the equipment has been added to "Machine version".
2.1.1 General
The weight of the equipment has been corrected from "Approx. 120 kg (264.55 lb.)" to
"Approx. 121 kg (266.75 lb.) (for NAD and MJD) and Approx. 123 kg (271.16 lb.) (for oth-
ers)".
2-12 2.3 Options
The model name of the EFI Printer Board has been corrected from "GA-1300" to "GA-
1211".
2-14 2.5 System List
The model name of the EFI Printer Board has been corrected from "GA-1300" to "GA-
1211".
8-8 8.4 Image Related Adjustment
Section 8.4 is now "SYSTEM CONTROL PC BOARD (SYS)" and "Image Related Adjust-
ment" has been moved to section 8.5.
8-11 8.5.2 Adjustment of the Auto-Toner Sensor (used to be 8.4.2)
The illustration of the procedure in step (5) has been changed.
12-5 New sections "12.4 Description of Operation" and "12.4.1 Drum phase registration mecha-
nism" have been added.
13-38 "13.6.1 Adjustment of the Auto-Toner Sensor" has been deleted because it is already men-
tioned in 8.5.2.
14-18 "Reflection tape" in "Notes" item No. 2 in step (7) has been corrected to "serial number".
14-19 PM mark has been removed from "14.6.5 Drive roller" because it is not a PM part.
14-21 "Never attempt to loosen 2 red screws shown in the figure." has been added to "Note".
18-6 "Noise filter" has been added to the diagram in "18.6 Configuration of Power Supply Unit".
19-12 The contents of C6 and C7 in the table in "19.5.3 Feed unit" have been corrected.
19-20 "H9: Developer unit upper cover" has been added to the figure and the table in "19.5.8
Developer unit (K, Y, M, and C)".
19-22 The content of "Handling precautions" in "*J1: Transfer belt" has been corrected.
19-23 "Handling precautions" and "Cleaning procedure" of "*J8: Transfer belt cleaning blade"
have been added.
19-25 "M12" in the figure of "19.5.13 Fuser unit" has been corrected to "M2".
19-32 In the table, "FR-KIT-FC35" has been corrected to "FR-KIT-FC28", "FR-FC35-U" has been
corrected to "FR-FC28-U" and "HR-FC35-L" has been corrected to "HR-FC28-L".
20-5 The data file name "menteusb2.o" of update program loader in the table "Program neces-
sary for updating" has been corrected to "mentusb2.o".
20-7 Precautions for options (GP-1070/1080, GS-1010/1020) have been added to "Important".
The data file name "menteusb2.o" of update program loader in step (1) of "[A] Update pro-
cedure" has been corrected to "mentusb2.o".
20-18 A data writing error handling procedure has been added to "[A] Precautions when writing
the data".
20-21 A note for update procedure has been added.
A procedure for unplugging and re-plugging the power cable has been added.
21-10 A disassembling procedure in "21.1.11 Board case" has been changed from step (2) to (2),
(3), (4) and (5), and from step (3) to (6).
21-23 The model name of the EFI printer board in "[K] Set EFI Printer Board" has been corrected
from "GA-1300" to "GA-1211".
21-26 The model name of the EFI printer board in "[F] Set EFI Printer Board" has been corrected
from "GA-1300" to "GA-1211".
21-26 "[G] Reinstall options" has been added.
© 2008, 2009 TOSHIBA TEC CORPORATION All rights reserved
Ver.01 <2008.04.24>
Contents
13
e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C
REVISION RECORD