Toshiba e-STUDIO2330C Service Manual page 1239
Hide thumbs
Also See for e-STUDIO2330C:
- Service handbook (512 pages) ,
- Management manual (226 pages) ,
- Copying manual (174 pages)
Table of Contents
Advertisement
Page
20-18
20.2.1 Writing the data to the download jig (PWA-DWNLD-350-JIG2) - [A] Precautions
when writing the System ROM data
A precaution "Loading the data file into the buffer by means of the following settings." has
been added.
20-18
20.2.1 Writing the data to the download jig (PWA-DWNLD-350-JIG2) - [A] Precautions
when writing the System ROM data-[A-1] System ROM
The name of the system ROM file has been corrected.
20-19
20.2.1 Writing the data to the download jig (PWA-DWNLD-350-JIG2) - [B] Precautions
when writing the Engine ROM data
Precautions when writing the Engine ROM data have been added.
20-21
20.2.2 System ROM - [A] Update procedure
Step 9: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
Step 10: The procedure for starting up the equipment has been changed to turning ON the
power with the main switch.
20-22
20.2.3 Engine ROM - [A] Update procedure
Step 1:The procedure has been corrected to "Write the ROM data to be updated to the
download jig (PWA-DWNLD-350-JIG2)."
20-23
20.2.3 Engine ROM - [A] Update procedure
Step 6: The illustration has been corrected.
Step 11: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
20-26
20.3.1 Scanner ROM - [A] Update procedure
Step 8: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
20-28
20.3.2 RADF firmware (MR-3018) - [A] Update procedure
Step 7: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
20-30
20.3.3 Finisher firmware (MJ-1101) - [A] Update procedure
Step 7: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
20-34
20.3.4 Converter Firmware (MJ-1101) - [A] Update procedure
Step 12: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
20-35
20.3.5 Hole punch unit firmware (MJ-6101) - [A] Checking the hole punch position
Step 1: The procedure has been changed to turning OFF the power with the [ON/OFF] but-
ton.
Step 3: The procedure has been changed to turning ON the power with the [0], [8] and [ON/
OFF] buttons.
Step 4: A procedure to set the DIP-SW1 back has been added as step (4).
20-37
20.3.5 Hole punch unit firmware (MJ-6101) - [B] Update procedure
Step 10: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
20-41
20.3.6 Finisher firmware/Saddle stitcher firmware (MJ-1030) - [A] Update procedure
Step 8: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
20-44
20.3.7 Finisher firmware (MJ-1031) - [A] Update procedure
Step 9: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
20-47
20.3.8 Fax unit firmware (GD-1250) - [A] Update procedure
Step 7: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
21-1
The illustration in Fig. 21-1 has been corrected.
21-4
The illustration in Fig. 21-9 has been corrected.
21-5
The illustration in Fig. 21-12 has been corrected.
© 2008, 2009 TOSHIBA TEC CORPORATION All rights reserved
Ver.02 <2008.06.26>
Contents
9
e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C
REVISION RECORD
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
