Toshiba e-STUDIO2330C Service Manual page 1238

Page
8-64 The content of the "Remarks" field in the table in "8.8.2 Density adjustment" has been cor-
rected.
8-67 Descriptions for "8.8.6 Setting range correction" have been corrected.
The content of the "Remarks" field in the table in "8.8.6 Setting range correction" has been
corrected.
9-1 The model name has been changed from "e-STUDIO2820C/2830C/3520C" to
"e-STUDIO2330C/2820C/2830C/3520C".
The illustration in Fig. 9-1 has been changed.
9-5 The model name has been changed from "e-STUDIO2820C/2830C/3520C" to "e-
STUDIO2330C/2820C/2830C/3520C".
10-1 The "magnet roller" has been changed to the "magnetic roller".
12-22 The removing procedure for the discharge LEDs has been changed.
13-12 PM mark has been added to the title of 13.5.2.
13-22 The amount of grease to be applied has been changed.
13-32 The removing procedure for the toner cover has been changed.
16-24 A note regarding to the handling of the pressure roller lamp has been added in step (8).
16-29 A note regarding to the handling of the heater lamps has been added in step (9).
16-35 The illustration of the pressure roller rear thermistor in Fig.16-51 has been corrected.
16-50 Descriptions in the adjustment procedure (1) have been changed.
18-6 Descriptions for "AC OFF detection" have been changed.
18-9 The model name "e-STUDIO2330C" has been added.
19-9 The description about the e-STUDIO2330C has been added in the table in No. 1 in Notes.
The model name "e-STUDIO2330C" has been added in No. 2 in Notes.
The model name "e-STUDIO2330C" has been added to the name of the service parts list in
No. 5 in Notes.
19-16 The number of sheets for replacement for the e-STUDIO2330C has been added in the
19-17 "x 1,000 sheets" field in the table.
19-20
19-21 The amount of grease to be applied has been changed.
19-23 The number of sheets for replacement for the e-STUDIO2330C has been added in the
19-26 "x 1,000 sheets" field in the table..
19-27
19-28 "Fuser belt thermopile (center/rear)" has been added in the table as "M14".
19-29 Descriptions for cleaning the fuser belt thermopiles have been added.
19-35 The part name of the ozone filter 1 has been changed from "FLTR-OZN-F380" to "FLTR-
OZN-45X-CB0-600M".
The slit glass cleaner pad has been added in the "Component" field for DEV-KIT-FC28K.
19-36 A harness jig for the converter board has been added as No. 14 in the "Maintenance Part
List" table.
Descriptions under the Table have been changed.
19-37 The illustration of a harness jig for the converter board has been added.
19-38 The model name "e-STUDIO2330C" has been added to the name of the service parts list
under the table "19.9 Grease List".
Descriptions for the e-STUDIO2330C have been added in "19.10 Operational Items in
Overhauling".
20-1 20. FIRMWARE UPDATING
Descriptions about the necessity of a harness jig for the converter firmware update have
been added.
20-2 E. Engine ROM
The illustration of the download jig has been corrected.
e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C
REVISION RECORD
Ver.02 <2008.06.26>
Contents
© 2008, 2009 TOSHIBA TEC CORPORATION All rights reserved
8