Table of Contents
Advertisement
Mixing
Track parameters
These parameters can be set for each track
Display
Parameter
PAN
PAN
EQ HI
High-frequency range boost/cut
TYPE
EQ HI
GAIN
FREQUENCY
EQ MID
Middle-frequency range boost
GAIN
EQ MID
FREQUENCY
Q
EQ LOW
Low-frequency range boost/cut
TYPE
EQ LO
GAIN
FREQUENCY
Send-return effect levels
REVERB
REV SEND
SEND LEVEL
CHORUS/
CHO SEND
DELAY SEND
LEVEL
FADER
FADER
ST LINK
STEREO LINK
INVERT
INVERT
NOTE
• Use the ON/OFF soft key to turn EQ HI, EQ MID,
EQ LO, REV SEND, CHO SEND and INVERT
parameters ON/OFF.
• When a stereo link is ON, the INVERT parameter
is shown as INVERT L for the odd odd track,
and as INVERT R for the even track.
41
Setting range
(default value)
L100~R100
Adjusts a track's PAN. For stereo tracks adjusts the
(Center)
volume balance between the left and right channels.
Set whether to boost/cut the high-frequency range (EQ
EQ HI, HI CUT
HI) or clearly cut unnecessary high frequencies (HI
(EQ HI)
CUT). This parameter can only be accessed when EQ
HI is ON.
Adjust amount of boost/cut of high frequencies by -12
–12dB~12dB
~ +12 dB. This parameter is shown only when the TYPE
(0dB)
is set to EQ HI. When set to HI CUT, it is not shown.
Adjust EQ boost/cut frequency of high frequencies.
500Hz~18kHz
This parameter can only be accessed when EQ HI is
(8.0kHz)
ON.
Adjust amount of boost/cut of medium frequencies by
–12dB~12dB
-12 ~ +12 dB. This parameter can only be accessed
(0dB)
when EQ MID is on.
Adjust EQ boost/cut frequency of medium frequencies.
40Hz~18kHz
This parameter can only be accessed when EQ MID is
(1.0kHz)
on.
Adjust the width of the medium frequency band af-
0.1~2.0
fected. This parameter can only be accessed when EQ
(0.5)
MID is on.
Set whether to boost/cut the low-frequency range (EQ
EQ LO, LO CUT
LO) or clearly cut unnecessary low frequencies (LO
(EQ LO)
CUT). This parameter can only be accessed when EQ
LO is on.
Adjust amount of boost/cut of low frequencies by -12
–12dB~12dB
~+12 dB. This parameter is shown only when the TYPE
(0dB)
is set to EQ LO. When set to LO CUT, it is not shown.
40Hz~1.6kHz
Adjust EQ boost/cut frequency of low frequencies. This
(125Hz)
parameter can only be accessed when EQ LO is on.
0~100
Adjust the signal level sent from the track to the reverb
(0)
effect.
0~100
Adjust the signal level sent from the track to the chorus/
(0)
delay effect.
0~127
Adjust the current volume.
(100)
On/Off
Switch on/off to set the stereo link function that
(Off)
connects two mono tracks together. (Ref. P.20)
On/Off
Set whether the phase of a track is inverted or not. Set
(Off)
it to Off to use normal phase or ON to invert the phase.
Explanation
Mono tracks: 1~24
Stereo tracks: 1/2~23/24
Mono
Stereo
Master
tracks
tracks
track
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
☞
◯
◯
◯
◯
◯
◯
◯
Advertisement
Table of Contents
