Table of Contents
Advertisement
Message
E R ROR 3 0 4
U S B
I N I T E R R
E R ROR 3 0 5
U S B T I ME OU T
E R ROR 4 0 1
MO T OR X
E R ROR 4 0 2
MO T OR Y
E R ROR 4 0 3
X C U R R E N T
E R ROR 4 0 4
Y C U R R E N T
E R ROR 4 2 3
T A K E - U P T E N S I ON B A R
E R ROR 4 2 4
F E E D I NG T E N S I ON B A R
E R ROR 4 2 5
T a k e - U P WRONG
E R ROR 4 2 6
F e e d i n g WRONG
E R ROR 4 2 7
T a k e - U P C o v e r O P E N
E R ROR 4 2 8
F e e d i n g C o v e r O P E N
E R ROR 4 2 9
T a k e - U P L i m i t D E T E C T
E R ROR 4 2 a
F e e d i n g L i m i t D E T E C T
E R ROR 4 2 b
F e e d i n g B a r
S h e l t e r
E R ROR 4 4 7
C U T T E R E N COD E R E R R
E R ROR 4 4 d
S T A T I ON P O S E R ROR
E R ROR 4 5 F
E X C HG . P o c t C u r e U V 1 2 3
E R ROR 5 0 5
ME D I A J AM
Cause
USB device initialization failure.
Occurrence of a time out error on a
USB device.
An excessive load was applied to the X
motor.
An excessive load was applied to the Y
motor.
An error due to an excessive current of
the X motor was detected.
An error due to an excessive current of
the Y motor was detected.
An error was detected in the take-up
tension bar at media set check when
starting printing.
An error was detected in the feeding
tension bar at media set check when
starting printing.
An error occurred in the take-up status
of the take-up unit.
An error occurred in the feeding status
of the feeding unit.
The take-up cover opened during print-
ing.
The feeding cover opened during print-
ing.
The take-up limit sensor was detected
during printing.
The feeding limit sensor was detected
during printing.
The tension bar is in the upper position
during printing.
An error occurred in the cutter encoder.
An error occurred in the station position.
Time to replace the post cure lamp has
come.
The media jam occurs.
Warning / Error Messages
Solution
• Turn off the main power to the machine
and turn it on after a while.
If the same error message appears
again, contact your local distributor to call
for service.
• Check the media set status, and solve
the problem.
• Check the media set status, and solve
the problem.
• Check that the media can be taken up to
the take-up unit.
• Check that the paper core taking up the
media does not run idle.
• Check that the media can be taken up to
the feeding unit.
• Check that the media does not run idle.
• Close the take-up cover.
• Close the feeding cover.
• Lower the tension bar or move it to the
waiting position.
• Lower the tension bar or move it to the
waiting position.
• Lower the tension bar.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for ser-
vice.
• For replaceing the lamp, refer to P.4-34
"About time to replace lamp".
• Remove the media and reset it.
1
1
1
1
5
5-17
Advertisement
Table of Contents
