Table of Contents
Advertisement
Message
< L OC A L >
Ym o t o r
C l e a n i n g [ MN T ]
< L OC A L >
R e p l a c e Ym o t o r
B r u s h
< L OC A L >
T a k e - U P C o v e r O P E N
< L OC A L >
T a k e - U P L i m i t D E T E C T
< L OC A L >
T a k e - U P WRONG
< L OC A L >
F e e d i n g C o v e r O P E N
< L OC A L >
F e e d i n g L i m i t D E T E C T
< L OC A L >
F e e d i n g WRONG
M i s t
F i l t e r
P l e a s e R e p l a c e
! P R E H E A T E R B R K
! P R I N T H E A T E R B R K
! P O S T H E A T E R B R K
< L OC A L >
P o s t C u r e U V 1 2 3
< L OC A L >
P O S T C U R E CO V E R O P E N
5-12
Cause
Time to clean the Y motor has come.
Time to replace the brush of Y motor
has come.
The cover of the media take-up
machine was open was detected.
The control limit sensor of the media
take-up machine was detected.
An abnormality occurred in the take-up
status of the media take-up machine.
The cover of the media feeding
machine was open was detected.
The control limit sensor of the media
feeding machine was detected.
An abnormality occurred in the feeding
status of the media feeding machine.
Time to replace the mist filter has come.
[ E N T ]
A platen heater is disconnected.
Time to replace the post cure lamp has
[ MN T ]
come.
The cover of the post cure lamp unit
was open was detected.
Solution
• Turn off the power and vacuum debris of
the Y motor from the vacuuming window.
(
P.4-28)
• After
the
replacement,
MAINT.
key on the local screen to
clear the warning.
• The brush of Y motor shall be replaced.
Contact a distributor in your district, our
office, or our call center.
• Check the cover of the media take-up
machine. Even if you close the cover, if
the same error is displayed, contact a
distributor in your district, our office or our
call center.
• Lower the position of the tension bar at
the take-up side. Even if you lower the
position, if the same message is dis-
played, contact a distributor in your dis-
trict, our office or our call center.
• Check that the media is set on the media
take-up machine correctly.
• Check that the paper core for taking up
media does not run idle.
• Check the cover of the media feeding
machine. Even if you close the cover, if
the same error is displayed, contact a
distributor in your district, our office or our
call center.
• Lower the position of the tension bar at
the feeding side. Even if you lower the
position, if the same message is dis-
played, contact a distributor in your dis-
trict, our office or our call center.
• Check that the media is set on the media
feeding machine correctly.
• Check that the paper core of roll media
does not run idle.
• For replaceing the filter, refer to the sepa-
rate "Requests for Daily Care and Main-
tenance".
• Turn off the main power to the machine
and turn it on after a while.
If the same error message appears
again, contact your local distributor to call
for service.
• For replaceing the lamp, refer to P.4-34
"About time to replace lamp".
• Check the cover of the post cure lamp
unit. Even if you close the cover, if the
same error is displayed, contact a distrib-
utor in your district, our office or our call
center.
press
the
Advertisement
Table of Contents
