Table of Contents
Advertisement
Message
< L OC A L >
N E G A T I V E P R E S S U R E
< L OC A L >
P O S I T I V E P R E S S U R E
< L OC A L >
N E G A T I V E P . A D J U S T
< L OC A L >
I N K N E A R E N D
[ E N T ]
< L OC A L >
E X P I R A T I ON
[ E N T ]
< L OC A L >
E X P I R A T I ON ( 1 M )
[ E N T ]
< L OC A L >
E X P I R A T I ON ( 2 M )
[ E N T ]
< L OC A L >
S U P P L Y
I N K
: MMC C Y Y K K
< L OC A L >
S u b t a n k S e n s : MMC C Y Y K K
< L OC A L >
I n k O v e r f l o w : MMC C Y Y K K
< L OC A L >
T A N K l e v r l H
: MMC C Y Y K K
< L OC A L >
T A N K l e v r l L
: MMC C Y Y K K
< L OC A L >
R e p l a c e D e A i r M o d u l e
< L OC A L >
M a c h i n e T EMP / H i
* * * ° C
< L OC A L >
* * * ° C
M a c h i n e T EMP / L o
Cause
The value of the negative pressure sen-
sor is abnormal.
The value of the positive pressure sen-
sor is abnormal.
Pressure needs to be adjusted.
The ink of the ink bottle has been nearly
used up.
The specified expiration date of an ink
bottle has passed.
The expiration date of an ink bottle has
passed (one month has passed after
the specified expiration date).
The expiration date of an ink bottle has
passed (two months have passed after
the specified expiration date).
Ink could not be supplied to the sub
tank.
The liquid level sensor abnormality of
the sub tank has been detected.
Overflow from the sub tank has been
detected.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor High.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor Low.
The deaeration module in the ink path
shall be replaced soon.
(One year has passed since you started
using it.)
The machine temperature is high.
The machine temperature is low.
Warning / Error Messages
Solution
• Perform
"PRESSURE
(
P.5-7) of the maintenance. If you
cannot adjust it to the normal value, or,
even if you perform, it may be displayed,
contact your local distributor to call for
service.
• Press the
key to check the rel-
evant ink bottle. Be careful because it
may be INK NEAR END soon.
The expiration date has passed.
However, you can use it until the end of the
following month.
• One month has passed after the expira-
tion date.
However, you can use it until the end of
this month. (The ink bottle lamp blinks in
red.)
Two months have passed after the expira-
tion date.
Replace the ink bottle generating the warn-
ing with a new one.
• Perform "SUB TANK" (
maintenance. Also check the remaining
amount of ink in the ink bottle. Even if you
performed this, when the message is dis-
played, contact your local distributor to
call for service.
• Turn off the power to the machine and
turn it on after a while.
• If the same error message appears
again, contact your local distributor to call
for service.
• Perform "SUB TANK" (
maintenance. Even if you performed this,
when the message is displayed, contact
your local distributor to call for service.
• The deaeration module shall be replaced.
Contact a distributor in your district, our
office, or our call center.
• Adjust the ambient temperature of the
installation place.
ADJUST"
1
1
P.5-6) of the
1
P.5-12) of the
1
5
5-11
Advertisement
Table of Contents
