Lenovo ThinkServer TS100 Hardware Maintenance Manual page 6

Removing and replacing optional-service CRUs . . . . . . . . . . . . . 86
Removing and replacing FRUs
Chapter 5. Diagnostics . . . . . . . . . . . . . . . . . . . . . 129
Diagnostic tools . . . . . . . . . . . . . . . . . . . . . . . . 129
POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Checkout procedure . . . . . . . . . . . . . . . . . . . . . . 145
iv
ThinkServer TS100 Types 6431, 6432, 6433, and 6434: Hardware Maintenance Manual
Installing the lower bezel . . . . . . . . . . . . . . . . . . . . 65
Removing the upper bezel. . . . . . . . . . . . . . . . . . . . 66
Installing the upper bezel . . . . . . . . . . . . . . . . . . . . 67
Removing an adapter . . . . . . . . . . . . . . . . . . . . . 68
Installing an adapter . . . . . . . . . . . . . . . . . . . . . . 69
Removing and installing internal drives . . . . . . . . . . . . . . . 71
Removing a hot-swap power supply . . . . . . . . . . . . . . . . 81
Installing a hot-swap power supply
Removing a memory module . . . . . . . . . . . . . . . . . . . 84
Installing a memory module . . . . . . . . . . . . . . . . . . . 85
Removing the battery . . . . . . . . . . . . . . . . . . . . . 86
Installing the battery . . . . . . . . . . . . . . . . . . . . . . 86
Removing the rear system fan . . . . . . . . . . . . . . . . . . 88
Installing the rear system fan. . . . . . . . . . . . . . . . . . . 89
Removing the hard disk drive fan assembly . . . . . . . . . . . . . 90
Installing the hard disk drive fan assembly . . . . . . . . . . . . . . 92
Removing the simple-swap backplate
Installing the simple-swap backplate . . . . . . . . . . . . . . . . 95
Removing the SAS/SATA hard disk drive backplane . . . . . . . . . . 96
Installing the SAS/SATA hard disk drive backplane . . . . . . . . . . . 97
Removing the front-panel assembly . . . . . . . . . . . . . . . . 99
Installing the front-panel assembly . . . . . . . . . . . . . . . . 100
Removing the front USB connector assembly . . . . . . . . . . . . 100
Removing the rear adapter retention bracket . . . . . . . . . . . . 101
Installing the rear adapter retention bracket . . . . . . . . . . . . . 102
Removing the front adapter-retention bracket . . . . . . . . . . . . 102
Installing the front adapter-retention bracket . . . . . . . . . . . . . 103
Installing the front USB connector assembly. . . . . . . . . . . . . 103
Removing the hot-swap power supply cage . . . . . . . . . . . . . 104
Installing the hot-swap power supply cage . . . . . . . . . . . . . 105
Removing the mini-SAS/SATA controller . . . . . . . . . . . . . . 106
Installing the SAS/SATA controller . . . . . . . . . . . . . . . . 107
Removing the optional mini-PCI-X enablement card . . . . . . . . . . 107
Installing the optional mini-PCI-X enablement card . . . . . . . . . . 108
Removing the RAID-MR10i SAS/SATA controller . . . . . . . . . . . 109
Installing the RAID-MR10i SAS/SATA controller
Removing an IBM Remote Supervisor Adapter II SlimLine adapter . . . . 112
Installing an IBM Remote Supervisor Adapter II SlimLine adapter . . . . . 113
Removing a non-hot-swap power supply . . . . . . . . . . . . . . 115
Installing a non-hot-swap power supply
Removing the microprocessor and fan sink . . . . . . . . . . . . . 118
Installing a microprocessor and fan sink . . . . . . . . . . . . . . 120
Removing the system board
Installing the system board . . . . . . . . . . . . . . . . . . . 125
POST beep codes . . . . . . . . . . . . . . . . . . . . . . 130
No-beep symptoms . . . . . . . . . . . . . . . . . . . . . . 132
Error logs . . . . . . . . . . . . . . . . . . . . . . . . . 133
POST error codes . . . . . . . . . . . . . . . . . . . . . . 135
About the checkout procedure . . . . . . . . . . . . . . . . . . 145
. . . . . . . . . . . . . . . . 83
. . . . . . . . . . . . . . . 93
. . . . . . . . . . . 110
. . . . . . . . . . . . . . . . . . 115
. . . . . . . . . . . . . . 117
. . . . . . . . . . . . . . . . . . 123