Installation; 75785 Standard Solvent Base And 75979 Aviator / Mgs Solvent Base Installation - Ransburg 75785 Service Manual

REA-90 and 90L Spray Applicators - Installation
INST INST ALLA ALLA
INST INST ALLA INST ALLA ALLA TION
75785 ST 75785 STANDARD 75785 ST 75785 ST 75785 ST ANDARD ANDARD ANDARD ANDARD
SOLVENT SOL SOL VENT VENT BASE AND VENT BASE AND BASE AND BASE AND
SOL SOL VENT BASE AND
75979 AVIA 75979 A 75979 A VIA VIA VIAT T T T T OR / MGS
75979 A 75979 A VIA
SOL SOL VENT VENT BASE BASE
SOL SOLVENT SOL VENT VENT BASE BASE BASE
INST INST ALLA ALLA TION TION
INSTALLA INST INST ALLA ALLATION TION TION
W A R N I N G W A R N I N G W A R N I N G
W A R N I N G W A R N I N G
! ! ! ! !
Installation of the equipment MUST be in
>
compliance with all Federal, State, and Local
Codes. Prior to installation, all personnel
should read and understand the NFPA-33, e
OSHA, and ITW Ransburg Bulletin "Operat-
ing Your Electrostatic Coating System
safely".
W A R N I N G W A R N I N G W A R N I N G W A R N I N G W A R N I N G
! ! ! ! !
NEVER wrap the applicator, associated NEVER NEVER NEVER NEVER
>
valves and tubing, and supporting hardware
in plastic to keep it clean. A surface charge
may build up on the plastic surface and
discharge to the nearest grounded object.
Efficiency of the applicator will also be
reduced and damage or failure of the applica-
tor components may occur. WRAPPING
THE APPLICATOR IN PLASTIC WILL THE APPLICATOR IN PLASTIC WILL THE APPLICATOR IN PLASTIC WILL THE APPLICATOR IN PLASTIC WILL THE APPLICATOR IN PLASTIC WILL
VOID WARRANTY. VOID WARRANTY. VOID WARRANTY. VOID WARRANTY. VOID WARRANTY.
Location of Control Unit Location of Control Unit Location of Control Unit Location of Control Unit Location of Control Unit
(Non-A (Non-A VIA VIAT T T T T OR Units) VIA OR Units) OR Units)
(Non-AVIA (Non-A (Non-A VIA OR Units) OR Units)
Install the low voltage control unit at least 3 feet
(0.9m) outside the spray area and/or in accordance
with federal, state, and local codes. Refer to the
low voltage control unit manual for mounting details.
The control unit can be wired through conduit or
with a line cord depending upon application
requirements and codes.
1 7 1 7 1 7 1 7 1 7
TION TION
TION TION
OR / MGS OR / MGS OR / MGS
OR / MGS
WRAPPING WRAPPING WRAPPING WRAPPING
The control unit MAY be connected through conduit
to an explosion-proof switch (to turn high voltage
on and off) and explosion-proof indicator light
(indicates status of control unit) within the
hazardous area for the convenience of the
operator.
Location of Control Unit Location of Control Unit Location of Control Unit Location of Control Unit Location of Control Unit
(A (AVIA (A (A VIA VIAT T T T T OR Units) VIA OR Units) OR Units)
(A VIA OR Units) OR Units)
The AVIATOR may be located within the hazardous
area. It may be mounted on a booth wall, pump
cart, or other suitable places. Refer to the AVIATOR
Power Generator manual for details on its

installation.

The air supply to the AVIATOR Power Generator
must be interlocked with the exhaust air for the
spray area. If a conveyor system is used, then the
air supply must be interlocked with it also.
Routing of Low V Routing of Low Voltage Cable Routing of Low V
Routing of Low V Routing of Low V
Position the spray applicator in the spray area and
route the low voltage cable to the control unit. The
cable should be routed so that it is not damaged by
foot and vehicle traffic and also so that it is not
close to areas of high temperature (129
operator should have free movement of the
applicator and all bend radius of the cable should
not be less than 6 inches (15 cm). Connect the low
voltage cable to the control unit and hand tighten
the retaining nut. If during the routing of the low
voltage cable it is required to remove it from the
spray applicator, care should be taken when
reinstalling it back that the retaining nut is wrench
tight and the nut cannot be removed by hand.
C A U T I O N C A U T I O N C A U T I O N C A U T I O N C A U T I O N
! ! ! ! !
Do NOT overtighten the low voltage
>
connection at the applicator. The plastic
parts could be damaged.
oltage Cable oltage Cable oltage Cable
oltage Cable
o F+). The
AH-94-04.7
A C A C
A C A C A C
I n I n I n I n I n