Table of Contents
Advertisement
REA-90 and 90L Spray Applicators - Installation
75786 ST
75786 ST
ANDARD
ANDARD
75786 ST
75786 STANDARD
75786 ST
ANDARD
ANDARD
W W W W W A A A A A TERBORNE AND
TERBORNE AND
TERBORNE AND
TERBORNE AND
TERBORNE AND
75982 A
75982 A
75982 AVIA
VIA
VIAT T T T T OR
VIA
75982 A
75982 A
VIA
W W W W W A A A A A TERBORNE
TERBORNE
TERBORNE
TERBORNE
TERBORNE
INST
INST
INSTALLA
ALLATION
ALLA
ALLA
TION
TION
TION
INST
INST
ALLA
TION
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
! ! ! ! !
Installation of the equipment MUST be in
>
compliance with all Federal, State, and
Local Codes. Prior to installation, all per-
sonnel should read and understand the
NFPA-33, OSHA, and ITW Ransburg
Bulletin "Operating Your Electrostatic
Coating System Safely".
The control unit MUST be located
>
outside of the spray area.
The fluid lines and fluid sources MUST
>
be isolated from ground.
Personnel MUST be GROUNDED to
>
prevent a shock or spark during electro-
static operation.
Install and route the hoses and cable so
>
they are NOT exposed to temperatures in
o
excess of 120
F and so that all hose and
cable bends are NO LESS than a 6-inch
(15cm) radius. Failure to comply with these
parameters could cause equipment mal-
function that might create HAZARDOUS
CONDITIONS!
Install only one spray applicator per
>
isolated fluid supply system.
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
! ! ! ! !
NEVER
NEVER
NEVER
NEVER wrap the applicator, associated
NEVER
>
valves and tubing, and supporting hardware
in plastic to keep it clean. A surface charge
may build up on the plastic surface and
discharge to the nearest grounded object.
Efficiency of the applicator will also be
reduced and damage or failure of the applica-
tor components may occur. WRAPPING
THE APPLICATOR IN PLASTIC WILL
THE APPLICATOR IN PLASTIC WILL
THE APPLICATOR IN PLASTIC WILL
THE APPLICATOR IN PLASTIC WILL
THE APPLICATOR IN PLASTIC WILL
VOID WARRANTY.
VOID WARRANTY.
VOID WARRANTY.
VOID WARRANTY.
VOID WARRANTY.
1 9
1 9
1 9
1 9
1 9
OR
OR
OR
OR
WRAPPING
WRAPPING
WRAPPING
WRAPPING
Location of Control Unit
Location of Control Unit
Location of Control Unit
Location of Control Unit
Location of Control Unit
(Non-A
(Non-A
VIA
VIA
VIAT T T T T OR Units)
OR Units)
OR Units)
(Non-AVIA
(Non-A
(Non-A
VIA
OR Units)
OR Units)
Position the low voltage control unit at least 3 feet
(0.9m) outside the spray area and in accordance
with federal, state, and local codes. Refer to the
Low Voltage Control Unit manual for mounting
details. The control unit can be wired through
conduit or with a line cord depending upon
application requirements and codes.
The control unit MAY be connected through conduit
to an explosion-proof switch (to turn high voltage
on and off) and explosion-proof indicator light
(indicates status of control unit) within the
hazardous area for the convenience of the
operator.
Location of Control Unit
Location of Control Unit
Location of Control Unit
Location of Control Unit
Location of Control Unit
(A (A
(A (AVIA
VIAT T T T T OR Units)
VIA
VIA
OR Units)
OR Units)
OR Units)
(A
VIA
OR Units)
The AVIATOR may be located within the hazardous
area. It may be mounted on a booth wall, pump
cart, or other suitable places.
AVIATOR Power Generator manual, for details on
its installation.
The air supply to the AVIATOR Power Generator
must be interlocked with the exhaust air for the
spray area. If a conveyor system is used, then the
air supply must be interlocked with it also.
Routing of Low V
Routing of Low Voltage Cable
Routing of Low V
Routing of Low V
Routing of Low V
Position the spray applicator in the spray area and
route the low voltage cable to the control unit. The
cable should be routed so that it is not damaged by
foot and vehicle traffic and also so that it is not
close to areas of high temperature (129
operator should have free movement of the
applicator and all bend radius of the cable should
not be less than 6 inches (15 cm). Connect the low
voltage cable to the control unit and hand tighten
the retaining nut. If during the routing of the low
voltage cable it is required to remove it from the
spray applicator, care should be taken when
reinstalling it back that the retaining nut is wrench
tight and cannot be removed by hand.
Refer to the
oltage Cable
oltage Cable
oltage Cable
oltage Cable
o
F+). The
AH-94-04.7
Advertisement
Table of Contents
