Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for B&D Easylifter
Summary of Contents for B&D Easylifter
-
Page 3: Table Of Contents
TABLE OF CONTENTS Adjustment Section 25-27 Introduction Adjust the travel limits ..........25 Safety rule review............2 Adjust the force ............26 Preparing your garage door ........3 Test the safety reverse system .........27 Tools needed ...............3 Testing the safety infra-red safety sensors ....27 Planning ..............4-5 Carton inventory ............6 Operation... -
Page 4: Preparing Your Garage Door
Preparing your garage door WARNING WARNING • Disable locks. Insert wood screws or nails to keep To prevent possible SERIOUS INJURY OR DEATH: them unlocked. • Always call for professional B&D garage door service CAUTION • Remove any ropes connected to garage door. if garage door binds, sticks, or is out of balance. -
Page 5: Planning
Planning – Alternate floor mounting of the safety infra-red beam sensors will require hardware not provided. Identify the type and height of your garage door. • Do you have an access door in addition to the Survey your garage area to see if any of the garage door? If not, a B&D Emergency Access conditions below apply to your installation. - Page 6 ONE-PIECE DOOR INSTALLATIONS • The gap between the bottom of the garage door and the floor cannot exceed 6mm. Otherwise, the • Generally, a one-piece door does not require safety reverse system may not work properly. See reinforcement. If your door is lightweight, you can Adjustment Step 3.
-
Page 7: Carton Inventory
Carton Inventory Your garage door opener is packaged in two cartons Hardware for assembly and installation is shown on which contains the motor unit and the parts illustrated the next page. Save the carton and packing material below. If anything is missing, carefully check the until installation and adjustment is complete. -
Page 8: Hardware Inventory
Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMBLY Spring /Trolley Nut (1) Washered Screw 25mm (4) Screw (2) Master (mounted in opener) Link (2) Car riage bolt (1) INSTALLATION Hex Screw Lock Washer Insulated Rail Grease... -
Page 9: Assembly
ASSEMBLY STEP 1 HARDWARE SHOWN ACTUAL SIZE Assemble the Rail NOTE: If your opener came with a one piece rail, proceed to Assembly step 2, page 9. Grease inside edges of rail brace sections. Place rail Spring Trolley Nut pieces on flat surface for assembly. All four rail sections are interchangeable. -
Page 10: Install The Trolley
ASSEMBLY STEP 2 Attach Trolley to Rail Slide outer trolley into rail assembly, be sure arrow on trolley is heading in direction of door is heading in direction of door. Slide outer trolley down rail until it engages with inner trolley. Arrow WARNING Rail Assembly... -
Page 11: Install The Chain Noise Reduction Pads
FASTEN RAIL TO OPENER SET CHAIN TENSION Spreader Stops HARDWARE SHOW ACT UAL SIZE Spring/Trolley Nut Nut Ring Screwdriver Wrench Bolt Trolley Stop Bolt Hole Spring Nut Lock Header Sleeve Washer Lock Washer Bolt Trolley Square Trolley Square Nut Ring Nut Ring AFTER RELEASE BEFORE... -
Page 12: Installation
INSTALLATION RNING WARNING IMPORTANT INSTALLATION INSTRUCTIONS TION WARNING WARNING To reduce the risk of severe injury or death: 1. READ AND FOLLOW ALL INSTALLATION in garage door or opener mechanisms. WARNINGS AND INSTRUCTIONS. 9. Install wall-mounted garage door control: 2. Install garage door opener only on properly balanced •... -
Page 13: Determine The Header Bracket Location
INSTALLATION STEP 1 Finished Ceiling Determine the Header Bracket Vertical 40mm Centreline Location Reinforcement Header Board Structural Wall Supports Installation procedures vary according to garage door types. Follow the instructions which apply to your door. WARNING To prevent possible SERIOUS INJURY or DEATH: •... - Page 14 ONE-PIECE DOOR WITHOUT TRACK Unfinished 1. Close the door and mark the inside vertical Ceiling centreline of your garage door. Extend the line 40mm onto the header wall above door, as shown. Structural Boa rd Header Supports If headroom clearance is minimal, you can install Vertical Wall Centreline...
-
Page 15: Install The Header Bracket
INSTALLATION STEP 2 Install the Header Bracket Bracket Holes WALL HEADER BRACKET INSTALLATION • Centre the bracket on the vertical guideline with the bottom edge of the bracket on the horizontal line (with the arrow pointing toward the ceiling). • Mark all of the bracket holes. Drill 4.5mm (3/16") pilot holes and fasten the bracket with wood screws. -
Page 16: Attach The Rail To The Header Bracket
INSTALLATION STEP 3 Attach the Rail to the Header Bracket • Position opener on garage floor below the header bracket. Use packing material to protect the cover. Raise rail until holes in the header sleeve and holes in the header bracket align. Join with clevis pins. Insert ring fasteners to secure. -
Page 17: Hang The Opener
ONE-PIECE DOOR WITHOUT TRACK 25mm • With the door fully open and parallel to the floor, Board laid flat Rail measure the distance from the floor to the top of the door. • Using a stepladder as a support, raise the top of the opener to this height. -
Page 18: Install The Door Control
INSTALLATION STEP 6 Remote Control Wall Mount 1. Locate wall mount bracket at least 1.5m above the floor. 2. Attach to the wall with 2 x ø 3.5 max flat head screws (not provided). 3. Slide remote control onto wall mount bracket. NOTE: Tightening the wall mount screws will reduce clearance between bracket and wall. -
Page 19: Wiring Instructions For Optional Accessories
WARNING WARNING WARNING WIRING INSTRUCTIONS FOR ACCESSORIES To prevent possible SERIOUS INJURY or DEATH from electrocution: • Place entrapment warning label on the inside of • Be sure power is not connected BEFORE installing door door as a reminder of safe operating procedures. control. -
Page 20: Attach The Emergency Release Rope And Handle
WARNING WARNING INSTALLATION STEP 8 Attach the Emergency Release • To prevent possible SERIOUS INJURY or DEATH from a Rope and Handle falling garage door: CAUTION – If possible, use emergency release handle to disengage • Thread one end of the rope through the hole in the trolley ONLY when garage door is CLOSED. -
Page 21: Installing The Safety Infra-Red Safety Sensors
The units must be installed inside the garage so that INSTALLATION STEP 10 the sending and receiving eyes face each other Install the Safety Infra-red across the door, between 100-150mm above the floor. Either can be installed on the left or right of the Reversing Sensors (Optional) door as long as the sun never shines directly into the It is recommended that safety infra-red reversing... -
Page 22: Fasten The Door Bracket
CAUTION INSTALLATION STEP 11 Fasten the Door Bracket Fibreglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door Follow instructions which apply to your door type as bracket. To prevent damage to garage doors reinforce inside illustrated below or on the following page. - Page 23 ONE-PIECE DOORS HARDWARE SHOWN ACTUAL SIZE Please read and comply with the warnings and Car riage Bolt 8mm x 65mm reinforcement instructions on the previous page. They apply to one-piece doors also. • Centre the door bracket on the top of the door, in line with the header bracket as shown.
-
Page 24: Connect Door Arm To Trolley
INSTALLATION STEP 12 Inner Trolley Connect Door Arm to Trolley Follow instructions which apply to your door type as Outer Trolley illustrated below and on the following page. SECTIONAL DOORS ONLY Ring Clevis Pin Fastener • Make sure garage door is fully closed. Pull the 8mm x 25mm emergency release handle to disconnect the outer trolley from the inner trolley. - Page 25 ALL ONE-PIECE DOORS Door Assemble the Door Arm: Bracket Ring Fastener • Fasten the straight and curved door arm sections Nuts Lock together to the longest possible length (with a 2 or Washers 3 hole overlap). Straight Clevis Pin • With the door closed, connect the straight door 8mm x 25mm arm section to the door bracket with the Screws...
-
Page 26: Adjustment Section
WARNING WARNING ADJUSTMENT STEP 1 Limit Adjustment Without a properly installed safety reversal system, persons CAUTION Run the opener through a complete travel cycle. (particularly small children) could be SERIOUSLY INJURED Limit adjustments are not necessary when the door or KILLED by a closing garage door. opens and closes completely and doesn't reverse •... -
Page 27: Adjust The Force
WARNING WARNING ADJUSTMENT STEP 2 Adjust the Force Without a properly installed safety reversal system, persons CAUTION The force, as measured on the closing edge of (particularly small children) could be SERIOUSLY INJURED the door, should not exceed 400N (40kg). If the or KILLED by a closing garage door. -
Page 28: Test The Safety Reverse System
WARNING ADJUSTMENT STEP 3 Test the Safety Reverse System Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED TEST or KILLED by a closing garage door. • With the door fully open, place a 40mm board on •... -
Page 29: Operation
OPERATION NING WARNING IMPORTANT SAFETY INSTRUCTIONS TION WARNING WARNING To reduce the risk of severe injury or death: 1. READ AND FOLLOW ALL WARNINGS AND 10. Safety reversal system MUST be tested every month. INSTRUCTIONS. Garage door MUST reverse on contact with 40mm high object on the floor. -
Page 30: To Open The Door Manually
To Open the Door Manually Care of Your Opener WARNING LIMIT AND FORCE ADJUSTMENTS: Weather conditions may • To prevent possible SERIOUS INJURY or DEATH from a cause some minor changes in Limit Controls falling garage door: door operation requiring some re-adjustments, particularly –... -
Page 31: Troubleshooting
Troubleshooting 7. Opener noise is disturbing in living quarters of home: 1. Opener doesn't operate from either door control or remote: If operational noise is a problem because of proximity of the • Does the opener have electric power? Plug lamp into outlet. opener to the living quarters, Vibration Isolator Kit 62155 If it doesn't light, check the fuse box or the circuit breaker. -
Page 32: Programming
PROGRAMMING SPECIFICATIONS Horsepower ....˜ .43 Rated Pull Force.....700N Below are instructions for programming your opener Stand-by power rating to operate with remote control transmitters. @ 230V......5.5W Motor To Code a Hand-held Remote Type ........Permanent split capacitor Control Transmitter Speed ......1500 rpm Volts ........230-240 Volts AC-50Hz Only USING THE “SMART”... - Page 33 Australia Pty Ltd. ‘Purchaser’ means the purchaser of the Opener. ‘Opener’ means the ‘Easylifter Automatic Garage Door Opener’ ‘Authorised Distributor’ means an approved B&D distributor of the Opener. ‘Major Components’ means all components of the Opener that make up the power head that is attached to a garage door.
- Page 34 WARRANTY Subject to paragraph 12 hereof; the obligations of B&D under this warranty are limited to those contained herein and such warranties are expressly in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular purpose and notwithstanding any course of dealing between the parties or custom and usage in the trade to the contrary.
- Page 36 QLD Office: 17 Oasis Court, Clontarf 4019. Ph: (07) 3883 0200 NSW Office: 34-36 Marigold St, Revesby 2212. Ph: (02) 9722 5555 VIC/TAS Office: 147-153 Canterbury Road, Kilsyth 3137. Ph: (03) 9237 7766 SA Office: 23 Frederick Road, Royal Park 5014. Ph: (08) 8440 4747 WA Office: 96 Mulgul Drive, Malaga 6090.
Need help?
Do you have a question about the Easylifter and is the answer not in the manual?
Questions and answers