Omron SYSDRIVE 3G3RV Series User Manual page 440

No. Name
L1-01 Motor protection selection
L1-02 Motor protection time constant
Alarm operation selection during
L1-03
motor overheating
Motor overheating operation selec-
L1-04
tion
Motor temperature input filter time
L1-05
constant
L2-01 Momentary power loss detection
Momentary power loss ridethru
L2-02
time
L2-03 Min. baseblock time
L2-04 Voltage recovery time
L2-05 Undervoltage detection level
L2-06 KEB deceleration time
L2-07 Momentary recovery time
Frequency reduction gain at KEB
L2-08
start
Stall prevention selection during
L3-01
accel
L3-02 Stall prevention level during accel
L3-03 Stall prevention limit during accel
Stall prevention selection during
L3-04
decel
Stall prevention selection during
L3-05
running
Stall prevention level during run-
L3-06
ning
L4-01 Speed agreement detection level
L4-02 Speed agreement detection width
Speed agreement detection level
L4-03
(+/-)
Speed agreement detection width
L4-04
(+/-)
Operation when frequency refer-
L4-05
ence is lost
Frequency reference for loss of fre-
L4-06
quency reference
L5-01 Number of auto restart attempts
L5-02 Auto restart operation selection
L6-01 Torque detection selection 1
L6-02 Torque detection level 1
L6-03 Torque detection time 1
L6-04 Torque detection selection 2
L6-05 Torque detection level 2
L6-06 Torque detection time 2
L7-01 Forward drive torque limit
L7-02 Reverse drive torque limit
Table 10.1 Parameters (Continued)
Fac-
Set-
tory No.
ting
Setting
1 L7-03 Forward regenerative torque limit
1.0 L7-04 Reverse regenerative torque limit
Protect selection for internal DB
3 L8-01
resistor
1 L8-02 Overheat pre-alarm level
Operation selection after overheat
0.20 L8-03
pre-alarm
Input open-phase protection selec-
0 L8-05
tion
Output open-phase protection
*6
L8-07
0.1
selection
0.1 L8-09 Ground protection selection
0.3 L8-10 Cooling fan control selection
*7
L8-11 Cooling fan control delay time
190
0.0 L8-12 Ambient temperature
OL2 characteristics selection at
*11
L8-15
0
low speeds
100 L8-18 Soft CLA selection
Hunting-prevention function selec-
1 N1-01
tion
120 N1-02 Hunting-prevention gain
Speed feedback detection control
50 N2-01
(AFR) gain
Speed feedback detection control
1 N2-02
(AFR) time constant
Speed feedback detection control
1 N2-03
(AFR) time constant 2
High-slip braking deceleration fre-
120 N3-01
quency width
0.0 N3-02 High-slip braking current limit
2.0 N3-03 High-slip braking stop dwell time
0.0 N3-04 High-slip braking OL time
2.0 o1-01 Monitor selection
0 o1-02 Monitor selection after powerup
Frequency units of reference set-
80.0 o1-03
ting and monitor
0 o1-05 LCD brightness
LOCAL/REMOTE key enable/dis-
0 o2-01
able
STOP key during control circuit
0 o2-02
terminal operation
150 o2-03 Parameter initial value
0.1 o2-04 kVA selection
Frequency reference setting
0 o2-05
method selection
Operation selection when digital
150 o2-06
operator is disconnected
0.1 o2-07 Cumulative operation time setting
Cumulative operation time selec-
200 o2-08
tion
200 o2-09 Factory use
Parameters
Fac-
Name tory
Setting
200
200
0
95
3
0
0
1
0
60
45
1
1
1
1.00
1.00
50
750
5
150
1.0
40
6
1
0
3
1
1
0
*6
0
0
0
0
0
-
Set-
ting
10
17
10-