Mitsubishi Electric FR-A700 Instruction Manual page 5

4.5 Torque control by real sensorless vector control, vector control ............. 118
4.5.1 Torque control ...................................................................................................................... 118
4.5.2 Setting procedure of real sensorless vector control (torque control) ................................... 120
4.5.3 Setting procedure of vector control (torque control) ............................................................ 121
4.5.4 Torque command (Pr. 803 to Pr. 806) .................................................................................. 122
4.5.5 Speed limit (Pr. 807 to Pr. 809) ........................................................................................... 124
4.5.6 Gain adjustment of torque control (Pr. 824, Pr. 825, Pr. 834, Pr. 835) ................................ 127
4.6 Position control by vector control ................................................................ 129
4.6.1 Position control .................................................................................................................... 129
4.6.2 Conditional position feed function by contact input (Pr. 419, Pr. 464 to Pr. 494) ................ 131
4.6.3 Position control (Pr. 419, Pr. 428 to Pr. 430) by inverter pulse train input ........................... 134
4.6.4 Setting of the electronic gear (Pr. 420, Pr. 421, Pr. 424) .................................................... 136
4.6.5 Setting of positioning adjustment parameter (Pr. 426, Pr. 427) ........................................... 137
4.6.6 Gain adjustment of position control (Pr. 422, Pr. 423, Pr. 425) ........................................... 138
4.6.7 Trouble shooting for when position control is not exercised normally ................................. 140
4.7 Adjustment of real sensorless vector control, vector control.................... 141
4.7.1 Speed detection filter and torque detection filter (Pr. 823, Pr. 827, Pr. 833, Pr. 837) ........ 141
4.7.2 Excitation ratio (Pr. 854) ..................................................................................................... 142
4.8 Adjust the output torque of the motor (current) .......................................... 143
4.8.1 Manual torque boost (Pr. 0, Pr. 46, Pr. 112)......................................................................... 143
4.8.2 Advanced magnetic flux vector control (Pr. 71, Pr. 80, Pr. 81, Pr. 89, Pr. 450,
Pr. 451, Pr. 453, Pr. 454, Pr. 569, Pr. 800) ......................................................................... 145
4.8.3 Slip compensation (Pr. 245 to Pr. 247)................................................................................. 149
4.8.4 Stall prevention operation (Pr. 22, Pr. 23, Pr. 48, Pr. 49, Pr. 66, Pr. 114, Pr. 115,
Pr. 148, Pr. 149, Pr. 154, Pr. 156, Pr. 157, Pr. 858, Pr. 868) ............................................... 150
4.8.5 Multiple rating (Pr. 570) ........................................................................................................ 155
4.9 Limit the output frequency............................................................................. 157
4.9.1 Maximum/minimum frequency (Pr. 1, Pr. 2, Pr. 18) ............................................................. 157
4.9.2 Avoid mechanical resonance points (Frequency jump) (Pr. 31 to Pr. 36) ............................ 158
4.10 Set V/F pattern................................................................................................. 159
4.10.1 Base frequency, voltage (Pr. 3, Pr. 19, Pr. 47, Pr. 113) ....................................................... 159
4.10.2 Load pattern selection (Pr. 14) ............................................................................................ 161
4.10.3 Elevator mode (automatic acceleration/deceleration) (Pr. 61, Pr. 64, Pr. 292) ................... 163
4.10.4 Adjustable 5 points V/F (Pr. 71, Pr. 100 to Pr. 109) ............................................................. 165
4.11 Frequency setting by external terminals ...................................................... 166
4.11.1 Multi-speed setting operation (Pr. 4 to Pr. 6, Pr. 24 to Pr. 27, Pr. 232 to Pr. 239) ............... 166
4.11.2 Jog operation (Pr. 15, Pr. 16) ............................................................................................... 168
III