miniature aircraft Fury 55 X-CELL Assembly Instructions Manual page 39

Illustration 6c
128-188
0112
128-196
Illustration 6d
onE-SIDE CoMPLETE
Locate the MA128-187 8mm head axle, four MA0844 90d head damper O-rings, two MA0331 m8x14x0.5 shim washers, two
MA0332 m8x14x1 shim washers, two MA0848-2 m8 retaining clips, two MA0086 m5x12 flanged socket bolts, and the MA0844-9
clip application tool. Refer to Illustration 6d for this step. Use retaining clip pliers (snap ring pliers) to install one of the MA0848-2
m8 retaining clips into the groove on the MA128-187 8m head axle. Slip on the MA0332 m8x14x1 shim washer, then the MA0331
m8x14x0.5 shim washer, then two MA0844-6 90d head damper O-rings. Miniature Aircraft USA recommends the use of both
thick and thin shim washers for 3D flying. If you are a beginner, you may choose to omit the use of the MA0331 m8x14x0.5 shim
washers. The result will be a model with a more stable hover and flight characteristic especially at lower head speeds. Slide the
head axle with shims and dampers into the head block. Now slip the other two MA0844-6 90d head damper O-rings, MA0331
m8x14x0.5 shim washer (if you choose to prepare the model for 3D flying), and the MA0332 m8x14x1 shim washer. Thread in (do
not use thread locking compound yet) an MA0086 m5x12 flanged socket bolt into the side of the axle where the MA0848-2 retaining
clip was installed. Slide on the MA0844-9 clip application tool onto the other side of the head axle, and thread in (do not use thread
locking compound yet) the other MA0086 m5x12 flanged socket bolt. Use a 4mm hex driver to hold one of MA0086 m5x12 flanged
socket bolts, and tighten the other until you feel a "click". The clip application tool presses the MA0848-2 retaining clip into the
groove. After the MA0848-2 m8 retaining clip is seated into the groove, remove the two MA0086 m5x12 flanged socket bolts and
set them aside for the next step.
0109
CA
0091
0848-2 gRoovE foR 0848-2
0332
0331
0844-6
2x
Locate two MA128-188 main blade grips w/0319 bearings,
two MA128-196 3-D bell mixer assemblies, two MA0112
m3x9.5 threaded control balls, two MA0109 m3x8 threaded
control balls, and two MA0091 m3x16 Phillips bolts.
Refer to Illustration 6c for this step. Thread the MA0112
m3x9.5 threaded control balls into the OUTER holes on the
MA128-196 3-D bell mixers. Note there is an inner hole,
for the Fury 55 application we do not recommend installing
the MA0112 m3x9.5 threaded control ball in this location.
Mounting the MA0112 m3x9.5 threaded control ball on the
inner hole on the Fury 55 may result in the binding and/or
failure of the MA0133-1 ball link. Thread the MA0109
m3x8 threaded control balls into the opposite side of each
MA128-196 3-D bell mixer. Slide the MA0091 m3x16
Phillips bolt through each bell mixer, and apply a small
amount of medium CA (cyanoacrylate) to the threads of the
bolt, then thread the bolt into the hole on the blade grip as
shown. It is important to thread the MA0091 Phillips bolts
into the correct hole on the blade grip for proper rotor head
geometry.
128-187
USE BoTH WASHERS
foR 3D fLyIng.
oMIT MA0331 foR
BEgInnERS
0844-6
2x
0331
0332
0848-2
39
0844-9
0086