Extron electronics XTP CrossPoint 1600 Setup Manual page 18

Command
Analog input presets (available for inputs on an XTP CP 4i VGA universal analog input board only)
NOTE: Analog input presets are a set of variables that can be saved. For the complete list, see the XTP CrossPoint Switchers User Guide.
Save an analog input preset
Recall an analog input preset
HDCP status
View input HDCP status
View HDCP status of all inputs
View output HDCP status
View HDCP status of all outputs
Video mutes
Video mute
Video unmute
Read video mute
Global video mute
Global video unmute
X!
NOTE: = Input number
X@
= Output number
X&
= Analog input preset
X*
= HDCP status (for inputs)
X(
= HDCP status (for outputs)
X1)
= Mute
Command
Input audio selection
Input audio selection
Example:
View input audio selection
View input audio all selections
Audio input gain and attenuation
NOTE: The set gain (G) and set attenuation (g) commands are case sensitive.
Set input level to +dB value
Example:
Set input level to -dB value
Increment gain
Example:
Decrement gain
Read input level
NOTE: • = Space
X!
= Input number
X1!
= Input audio source
X1@
= Audio gain
X1#
= Numeric dB value
X1$
= Audio attenuation
SIS Command Response
(Host to Unit) (Unit to Host)
X! X& X!
*1* , Spr *1*
X! X& X!
*1* . Rpr *1*
E I X! HDCP } X*]
E } X* X* X*
I*HDCP 1 2
E X@ } X(]
O HDCP
E } X( X( X(
O*HDCP
1 2
X@ X@
*1B Vmt *1
X@ X@
*0B Vmt *0
X@ X1)]
B
]
1*B Vmt1
]
0*B Vmt0
01 – 16 or 32
01 – 16 or 32
1 through 8
0 = no source connected
0, 2, 4, or 6 = no monitor connected
7 = monitor connected and encrypted
0 = off (unmuted)
SIS Command Response
(Host to Unit) (Unit to Host)
E X! X1! } X!
I * AFMT AfmtI
E }
I1*0AFMT AfmtI1*0
E X! } X1!]
I AFMT
E IAFMT } X1! X1!
1 2
X! * X1@ G In X!
•Aud
1*2G In01•Aud+02
X! X1$ X!
* g In •Aud
X! X!
+G In •Aud
5+G In05•Aud+03
X! X!
–G In •Aud
X! X1#]
G
01 – 16 or 32
0 = Auto (see the example above)
1 = HDMI (de-embedded digital audio) (default)
0 to +24 (1 dB per step)
–18 to +24 (45 steps of gain or attenuation) (Default = 0 dB)
1 – 18 (1 dB per step)
Additional Description
X&]
Command character is a comma.
X&]
Command character is a period.
X* ]
3 ... n
X( ]
...
3 n
]
Mute output
]
Unmute output
1 = mute on, 0 = mute off.
Mute all video outputs.
Unmute all video outputs.
1 = source is HDCP compliant
1, 3, or 5 = monitor connected but not encrypted
1 = on (muted)
Additional Description
X1!]
*
]
Auto (0): Digital audio takes priority over analog audio.
X1! X1! ] X1!
3 ... n Each is the enable or disable status of an output,
starting at output 1. n is 16 or 32.
X1#]
]
Set input 1 audio gain to +2 dB.
X1#]
X1#]
Increase gain by 1 dB.
]
Increase audio input 5 level from +2 dB to +3 dB.
X1#]
Decrease gain by 1 dB.
2 = Analog (local 2-channel audio)
X@
(video off).
X@
(video on).
2 = source is not HDCP compliant