Honda EP3 Service Manual page 476

1 4 . I n s t a l l t h e d i s t a n c e c o l l a r ( A ) , 3 5 m m s h i m , a n d o l d
ball bearing (B) using the special tools and a press
(c).
Measure the clearance between the old bearing
a n d t h e 3 5 m m s h i m ( B ) w i t h a f e e l e r g a u g e ( C ) .
Standard: 0.04 0.10 mm 10.002 0.004 in.)
(A)
t 5 .
16. lf the clearance is more than the standard, select a
new shim from the following table. lf the clearance
measured in step 15 is within the standard, replace
o n l y t h e b a l l b e a r i n g .
35 mm Shim
Part Number Thickness
23981-PPP-0000.87 mm (0.0343
n .
B 23981-PPP-9000 . 9 1 m m { 0 . 0 3 5 8 n ,
c
23982-PPP-0000 . 9 5 m m ( 0 . 0 3 7 4 n .
D
23982-PPP-9000.99 mm (0.0390 n ,
E
23983-PPP-0001 . 0 3 m m 1 0 . 0 4 0 6 n ,
F
23983-PPP-900
1 . 0 7 m m ( 0 . 0 4 2 1 n .
23984-PPP-0001 . 1 1 m m ( 0 . 0 4 3 7 n .
11
23984-PPP-9001 . 1 5 m m ( 0 . 0 4 5 3 n .
J
23985-PPP-000
1 . ' 1 9 m m ( 0 . 0 4 6 9 n .
K
23985-PPP-900 1 . 2 3 m m ( 0 . 0 4 8 4
n
L
23986-PPP-000 1 . 2 7 m m ( 0 . 0 5 0 0
n .
M 23986-PPP-900
1 . 3 1 m m ( 0 . 0 5 1 6 i n .
N
23987-PPP-000
1 . 3 5 m m ( 0 . 0 5 3 1 i n .
P 23987-PPP-900
1 . 3 9 m m ( 0 . 0 5 4 7 n .
o
23988-PPP-000
1 . 4 3 m m ( 0 . 0 5 6 3 i n .
R 23988-PPP-900
1 . 4 7 m m ( 0 . 0 5 7 9 i n
23989-PPP-000 1 . 5 1 m m ( 0 . 0 5 9 4 i n
T
23989-PPP-900 1 . 5 5 m m ( 0 . 0 6 1 0 i n
U 23990-PPP-000 1 . 5 9 m m { 0 . 0 6 2 6 i n .
1 . 6 3 m m { 0 , 0 6 4 2 i n . 23990-PPP-900
X 23991-PPP-000
1 . 6 7 m m ( 0 , 0 6 5 7 i n
Y
23991-PPP-900 1 . 7 1 m m { 0 . 0 6 7 3 i n
z
23992-PPP-000
1 . 7 5 m m ( 0 . 0 6 8 9 i n
23992-PPP-900
1 . 7 9 m m ( 0 . 0 7 0 5 i n
AB
23993-PPP-0001 . 8 3 m m ( 0 . 0 7 2 0 i n
AC
23993-PPP-900
1 . 8 7 m m ( 0 . 0 7 3 6 i n
AD 23994-PPP-000
' 1 . 9 1 m m ( 0 . 0 7 5 2 i n
AE
23994'PPP-900 1 . 9 5 m m ( 0 . 0 7 6 8 i n .
AF
23995 PPP-000
1 . 9 9 m m ( 0 . 0 7 8 3 i n .
{cont'd)
13-37