Page 1
Digital Active Indoor Antenna SRT ANT 10 ECO User Manual...
Page 2
SRT ANT 10 ECO 1. INTRODUCTION Thank you for purchasing the STRONG SRT ANT 10 ECO DVB-T/T2 Antenna. This antenna has been specially designed to receive digital terrestrial signals from the air. It can be connected to any Digital Terrestrial Receiver (DVB-T/T2), and is designed for INDOOR use only.
SRT ANT 10 ECO 4. CONNECTING THE ANTENNA Check if the broadcast in your country is horizontal or vertical polarized. Click the antenna in the plastic holder as shown in the pictures: (H-Broadcast) antenna (V-Broadcast) antenna...
Page 4
The best position can be found by trying different locations. NOTE: It is recommended NOT to place the antenna near to: Devices that are strong source of radiation or interference such as DECT and GSM telephones, transmitters, microwaves, etc.
Page 5
Digital Terrestrial Receiver SRT 5300 User manual www.strong.tv 17 Feb 2011 21:16...
6.2 Accessing the Electronic Program Guide (EPG) 6.3 Accessing the favourite channels 7.0 TRoUblE ShooTIng 8.0 SPECIfICATIonS STRong declares that this item complies with the basic requirements and other relevant regulations of directives * €0,14/Min. from German wired line * €0.42/Min. max. from mobile network CE 2004/108/EEC and 73/23EEC;...
Attachments – For your safety and to avoid damaging the product, use only accessories recommended by STRONG. Water and moisture – Never use this product around water (near a bathtub, kitchen sink, laundry tub, wet basement. swimming pool or in the rain) location –...
PART 1 • English heat – Never use or store this product near any heat source such as a radiator heat register, stove, or any type of equipment or appliance that generates heat, including stereo amplifiers. Servicing – Refer all servicing to qualified personnel. Attempting to remove the covers or disassemble the product, could expose you to dangerous high voltage points.
PART 1 • English 1.4 features & Accessories For all* digital Free-To-Air TV and Radio programmes (with outdoor- or indoor antenna) Quick and easy installation & user-friendly menu Excellent Audio- and Video quality 1.000 channels memory capacity ...
the receiver. Always make backups of data on USB storage device before usage with receiver. STRONG will not take responsibility for any loss of information or circumstances caused by loss of information. 2.0 ConnECTIon 2.1 Connecting to Tv and Terrestrial Antenna To receive the broadcast signal, the terrestrial antenna cable should be connected to the ANT IN connector at the back of the receiver.
PART 1 • English 3.3 Remote Control Fig. 4 1. q Turns the receiver On/Standby 2. ! Mutes audio output of the receiver 3. Pg+/Pg- Page up/down 4. DTv/vCR No function 5. Info Shows the actual channel information 6. vol+/vol- Volume up/down 7.
Page 13
PART 1 • English 3. Press EXIT to exit. noTE: You can also press oK in TV mode to enter the channel list. 5.1.1 Tv Channel list 1. In Channel submenu select TV Channel List with the qp buttons and press oK to enter. 2.
PART 1 • English FTA: First in the list will be Free-To-Air channels. Lock: Unlocked channels will be listed first, followed by all locked channels. 5.1.1.4 move Press the button 4 to activate the Move function. p symbol. Use the qp buttons to move the selected The selected channel will be marked with the channel to the desired position.
PART 1 • English 4. When By Channel is selected use the cursor buttons to select Scan Band and Channel No.. When By Frequency is selected use the cursor buttons to select Frequency and Bandwidth. Set Network Search to ON or OFF, highlight Search and press oK to start scanning.
PART 1 • English Region: This menu is used for changing the region setting. GMT Usage: This setting allows you to switch the usage of GMT time on or off. The options are: Off / User Define / By Region GMT Offset: This menu is valid only when User Define is selected in GMT Usage menu.
2. Press EXIT to leave. 5.4.1 Receiver Information This menu displays relevant Receiver information like the Receiver Model, Software version, Signature, and our website www.strong.tv. 1. In Tools menu, select Receiver Information and press oK to open receiver information. 2. Press EXIT to leave.
This receiver is equipped with an over the air update function, which might not be operational in your broadcast region. For further details visit our website www.strong.tv or contact your local Service line. 5.5 media+ Select Media+ and press oK to enter Media+ menu.
If the receiver does not work properly after checking it, please contact your local Service line or STRONG dealer. Alternatively you can send a support mail via our website: www.strong.tv. Do noT open the receiver cover. It may cause a dangerous situation and will void the warranty.
Remote batteries exhausted Replace remote batteries Forgotten PIN code Contact local Service Hotline or send email to our Support via www. strong.tv After moving the receiver Antenna signals are too weak Press the Info button on remote to another room / area...
Page 21
PART 1 • English memory and System: Flash memory: 1 MByte SDRAM: 8 MBytes Connectors: ANT IN: IEC Female TO TV: IEC Male TV SCART (RGB, CVBS) S/PDIF: coaxial output USB 1.1 port: max. 5 V/800 mA general Data: Supply Voltage: 220 –...