Terms & Functions - Standard Horizon CP150 Owner's Manual

8. TERMS & FUNCTIONS
This Section explains the terms that may be unfamiliar to the reader. The symbol
indicates that the term is followed only by an explanation, while the symbol
indicates that the term is more widely explained; you will also find a brief description
on how to select the related menu option, listing the operation a keys sequence with
the menu names enclosed between double apices. For example 'MENU' + "USER
POINTS LIST" + 'ENTER' means that you must press the 'MENU' key, using the
ShuttlePoint knob to select the USER POINTS LIST item and then press the 'ENTER'
key to display the User Points List page.
About (page)
Selects a page that gives information on software and cartography version and general software
specification (as User Points, Routes and so on). For more information see Section 1.3.
'MENU' + "About..." + 'ENTER'
Active Track
Selects the number of the active Track. The default setting is 1.
'MENU' + "TRACK" + 'ENTER' + "ACTIVE TRACK" + 'ENTER'
Additional Second Factor (ASF)
Sets the ASF for the slave in the selected chain. The default setting is 0.
'MENU' + "ADVANCED SETUP" + 'ENTER' + "NAVIGATE" + 'ENTER' + "COORDINATE SYSTEM" +
'ENTER' + "TD" + 'ENTER' + "ASF1/2" + 'ENTER'
Advanced Setup (menu)
Selects the Fix, Navigate, Compass, Input/Output, Alarms, Simulation menus.
'MENU' + "ADVANCED SETUP" + 'ENTER'
Alarms (menu)
Turns Off or sets the desired value for the Arrival Alarm, XTE Alarm, Depth Alarm, Anchor Alarm e
Audible Alarm.
'MENU' + "ADVANCED SETUP" + 'ENTER' + "ALARMS" + 'ENTER'
Alter = Alternate Solution
Turns On/Off the Alternate Solution in the chain. The default setting is Off.
'MENU' + "ADVANCED SETUP" + 'ENTER' + "NAVIGATE" + 'ENTER' + "COORDINATE SYSTEM" +
'ENTER' + "TD" + 'ENTER' + "Alter" + 'ENTER'
Altitude (Unit)
Sets the altitude unit among Ft = Feet, FL = Flight Level and Mt = Meters. The default setting is Ft.
'MENU' + "GENERAL SETUP" + 'ENTER' + "UNITS OF MEASURE" + 'ENTER' + "ALTITUDE" + 'ENTER'
Anchor Alarm
This function allows inserting of the limit of anchor dragging: beyond that, the alarm is activated. The
chartplotter computes the distance between the current GPS position and the GPS position saved at the
activation of the anchor alarm in the menu. If the computed distance exceeds the value set in the menu,
the chartplotter shows the alarm message and starts the acoustic alarm. The default setting is Off.
'MENU' + "ADVANCED SETUP" + 'ENTER' + "ALARMS" + 'ENTER' + "ANCHOR ALARM" + 'ENTER'
Arrival Alarm
Specifies the radius of a circle around the Waypoint of a Route: when your vessel reaches this circle
the alarm sounds. You can disable (Off) the Arrival Alarm or insert value. The default setting is Off.
'MENU' + "ADVANCED SETUP" + 'ENTER' + "ALARMS" + 'ENTER' + "ARRIVAL ALARM" + 'ENTER'
Arrival Time
The estimated time of day you will reach your destination, based on your current speed and track from
GPS.
Attention Areas
Enables by filling area (On), enables only contour (Contour) or disables (Off) the displaying of the
Attention Areas (areas in which special attention by the mariner is required, because of natural or man-
made hazards, or sailing regulations and restrictions). Moreover a special symbol (!) is placed inside
Page 60 GPS Chart 150