Page 1 P3N1-E202-01ENZ0 XG2000 series User's Guide...
Page 2: All Rights Reserved, Copyright (C) Pfu Limited
XG2000 series User's Guide Preface You have purchased the XG2000 series, a compact, 20-port 10 Gigabit Ethernet layer 2 switch that achieves unsurpassed standards of high throughput and low-latency performance. This guide describes the XG2000 series (XG2000 / XG2000R / XG2000C / XG2000CR) functions, installation procedures, configuration operations, and maintenance procedures and should be read and understood before you start using your XG2000 series.
Page 3: About This Manual
Basic knowledge of system security This guide omits explanations of network protocol terms. Contents This guide to the XG2000 series is composed of the following chapters. Chapter 1. Features and Functions Describes the features and functions. Chapter 2. Using the CLI Describes operating environment of CLI and how to operate CLI.
Page 4: Table Of Contents
XG2000 series User's Guide Contents Preface ..................................2 About this Manual...............................3 Contents ..................................4 Chapter 1 Features and Functions ........................10 1.1 Features ................................11 Chapter 2 Using the CLI............................12 2.1 Overview of the CLI ............................13 2.1.1 Operating Environment for the CLI ......................13 2.1.2 Command Modes and Mode Switching ......................14 2.1.3 startup-config and running-config........................16...
Page 5 XG2000 series User's Guide 4.7 VLAN .................................41 4.7.1 Port-Based VLAN ............................41 4.7.2 Tag-Based (IEEE802.1Q) VLAN .........................42 4.7.3 Multiple VLAN..............................43 4.8 Quality of Service (QoS)............................46 4.9 IGMP Snooping ..............................47 4.9.1 Registering Group Members ........................48 4.9.2 Removing Group Members .........................49 4.9.3 Managing Group Members .........................50 4.9.4 IGMP Querier ..............................51...
Page 6 XG2000 series User's Guide 5.4.20 enable password ............................87 5.4.21 banner ...............................88 5.4.22 ntp-server ..............................89 5.5 RADIUS/TACACS+............................90 5.5.1 show authentication.............................90 5.5.2 aaa authentication login ..........................91 5.5.3 show radius ..............................92 5.5.4 radius-server host............................93 5.5.5 radius-server key............................94 5.5.6 radius-server timeout...........................95 5.5.7 show tacacs..............................96 5.5.8 tacacs-server host ............................97...
Page 7 XG2000 series User's Guide 5.11 Spanning Tree Protocol (STP) Configuration Commands................156 5.11.1 show spanning-tree ..........................156 5.11.2 spanning-tree............................161 5.11.3 spanning-tree priority..........................162 5.11.4 spanning-tree hello-time ..........................163 5.11.5 spanning-tree max-age..........................164 5.11.6 spanning-tree forward-time........................165 5.11.7 spanning-tree port-priority ........................166 5.11.8 spanning-tree port-path-cost ........................166 5.11.9 spanning-tree path-cost-default.......................167 5.11.10 spanning-tree portfast..........................168...
Page 8 XG2000 series User's Guide 5.16.9 monitor error............................221 5.16.10 show statistics traffic-bytes........................223 5.16.11 show statistics traffic-counts........................224 5.16.12 show statistics framesize-traffic-counts....................225 5.16.13 show statistics qos-priority-traffic-bytes ....................226 5.16.14 show statistics qos-priority-traffic-counts ....................227 5.16.15 show statistics vlan-traffic-bytes......................228 5.16.16 show statistics vlan-traffic-counts......................229 5.16.17 show statistics dataflow.........................230 5.16.18 show statistics error..........................231...
Page 9 XG2000 series User's Guide Appendix A Event Logs............................280 Overview of Event Logs ..........................280 List of Event Logs............................281 A.2.1 env (Health Monitoring: 0-999)......................281 A.2.2 kernel (Basic Control: 1000-1999)......................283 A.2.3 swc (Layer 2 Basic Control: 2000-2999) ....................284 A.2.4 npm (Network Protocol Control: 3000-3299)..................288 A.2.5...
Page 10: Chapter 1 Features And Functions
XG2000 series User's Guide Chapter 1 Features and Functions This chapter describes the features and functions of the device. 10/315 All Rights Reserved, Copyright (C) PFU LIMITED 2009...
Page 11: Features
XG2000 series User's Guide 1.1 Features The XG2000 series is a compact, 20-port 10 Gigabit Ethernet Layer 2 switch. Special features of the XG2000 series are shown below: Item Function Features Basic Switch Functions Throughput 400Gbit/s Latency 350ns (Exclude latency of XFPs) Switching mode Either store-and-forward or cut-through is selectable.
Page 12: Chapter 2 Using The Cli
XG2000 series User's Guide Chapter 2 Using the CLI This chapter describes how to use the command line interface (CLI) to operate the device. 12/315 All Rights Reserved, Copyright (C) PFU LIMITED 2009...
Page 13: Overview Of The Cli
XG2000 series User's Guide 2.1 Overview of the CLI This section describes how to use the command line interface (CLI) for the XG Series. 2.1.1 Operating Environment for the CLI There are two ways to access the device to run commands. Up to 5 terminal sessions can access the device concurrently.
Page 14: Command Modes And Mode Switching
XG2000 series User's Guide 2.1.2 Command Modes and Mode Switching The following table shows a hierarchy of command modes and mode switching. Command Modes and Prompt Text Outline (host name for the device: xg) Operator class The initial-level operating mode entered upon logging into the system.
Page 15 XG2000 series User's Guide Entering a specific command allows switching from one mode to another. Entering the "exit" command returns program control to the previous mode. Entering "end" command or pressing [Ctrl] and [Z], or [C] simultaneously in the global configuration, interface edit or terminal edit mode transfers program control to the administrator EXEC mode.
Page 16: Startup-Config And Running-Config
XG2000 series User's Guide 2.1.3 startup-config and running-config The configuration information is saved to startup-config and running-config files. This section describes the functions of the startup-config and running-config files. startup-config Startup-config is the configuration file that stores the environment settings that are enabled upon device startup.
Page 17: Using The Cli
XG2000 series User's Guide 2.2 Using the CLI 2.2.1 How to Enter Commands Command Entry Format Separate each command, subcommand and argument with a single space. <command> <subcommand> <argument 1> <argument 2> ... (" " indicates a space.) xg(config)# management-interface ip 192.168.1.10/24 default-gw 192.168.1.150 xg(config)# management-interface dns-server 192.168.1.150...
Page 18: Command Completion
XG2000 series User's Guide 2.2.3 Command Completion Entering part of a command or option and pressing the [Tab] key, causes the CLI to display the remaining command or option characters. xg# con<TAB> ↓ xg# configure _ For example, the only command that begins with "con" is "configure", so the CLI completes the command name as "configure".
Page 19: Command History
XG2000 series User's Guide Combinations of keys Description Recalls the previous command. "↑" or [Ctrl] + [P] Recalls the next command. "↓" or [Ctrl] + [N] Moves the cursor back one character. "←" or [Ctrl] + [B] Moves the cursor forward one character.
Page 20: Filtering Show Command Output
XG2000 series User's Guide 2.2.10 Filtering show Command Output This function allows filtering the show command output so lines that only satisfy specific conditions (filter for strings) are displayed. This function is useful in excluding unnecessary information from a large amount of output.
Page 21: Using The Monitor Command
XG2000 series User's Guide In the following example, show command output is redirected to TFTP server "remote-host1" using "| tftp". xg# show startup-config | tftp remote-host1 restore_ startup_09302005 xg# show running-config | tftp remote-host1 restore_running_09302005 xg# show system information | tftp remote-host1 restore_system_09302005 In the following example, show command output is redirected to SSH server "remote-host2"...
Page 22: Chapter 3 Installation
XG2000 series User's Guide Chapter 3 Installation This chapter describes the installation procedures for the device. Refer to "Using the CLI" for details on using the CLI. Refer to "Command Reference" for details on commands. 22/315 All Rights Reserved, Copyright (C) PFU LIMITED 2009...
Page 23: Workflow For Initial Setup Of The Device
XG2000 series User's Guide 3.1 Workflow for Initial Setup of the Device This section describes the procedures to setup the device. Prepare a terminal Prepare a terminal for the initial configuration. Setting Up the Serial Interface Connect the device and terminal with an RS232C cable. The initial baud rate setting is 9,600 bps.
Page 24: Configure Management Lan Interface
XG2000 series User's Guide 3.1.2 Configure Management LAN Interface The management LAN interface is initially enabled. (IP address: 192.168.0.2, subnet address: 255.255.255.0) To use the following functions, configure the management LAN interface. − Telnet connection (enabled by default) − SSH connection (disabled by default) −...
Page 25: Ssh Connection Via The Management Lan Interface (Optional)
XG2000 series User's Guide 3.1.4 SSH Connection via the Management LAN Interface (Optional) This device supports the “SSH server function”. This function is remote connection like “Telnet server function”. After executing “ssh-server” command, the “SSH-server” is enabled and authentication key is generated (It takes some time to generate authentication key).
Page 26: Chapter 4 Switch Functions And Their Configuration
XG2000 series User's Guide Chapter 4 Switch Functions and their Configuration This chapter describes the functions of the device and how to configure them. Refer to "Operating Environment for the CLI" for details on using the CLI. Refer to "Command Reference"...
Page 27: Basic Switch Functions
XG2000 series User's Guide 4.1 Basic Switch Functions This section describes the basic switch functions. 4.1.1 Switching Mode The device provides the following two switching modes. Store-and-forward switching mode After the device finishes receiving a frame, it checks the FCS (Frame Check Sequence) and performs a validity check (on packet size, etc.) before forwarding the frame.
Page 28: Jumbo Frame Support
XG2000 series User's Guide Static unicast address By registering a unicast MAC address with the MAC address table, unicast frames are forwarded to a specified port. Static unicast addresses are not subject to MAC address removal controlled by the aging function.
Page 29: Storm Control
XG2000 series User's Guide 4.1.5 Storm Control The device discards broadcast frames when the number of received broadcast frames are over a given threshold to prevent unnecessary waste of bandwidth due to retained broadcast frames on the network. This function is called "Storm Control".
Page 30: Port Mirroring
XG2000 series User's Guide 4.2 Port Mirroring It is possible to monitor the traffic by mirroring the frames sent or received by a port to another port. To configure port mirroring, carry out the following procedure in the administrator EXEC mode.
Page 31: Link Pass Through
XG2000 series User's Guide 4.3 Link Pass Through Link pass through is a function that monitors the status of a specified port link and notifies the device connected to the port via link status notification of the link status of a monitored port by synchronizing the monitored port with the link status on the port.
Page 32: Link Aggregation
XG2000 series User's Guide 4.4 Link Aggregation Link aggregation is a function that combines multiple ports into a single logical link. A set of ports that comprise a logical link is called an aggregation group. Link aggregation provides: Increased bandwidth...
Page 33: Configuring Link Aggregation
XG2000 series User's Guide 4.4.1 Configuring Link Aggregation Either static or dynamic (also known as LACP) configuration can be selected for Link Aggregation. Static configuration Configures aggregation groups statically. LACP Configures link aggregation using Link Aggregation Control Protocol (LACP). The LACP is a switch-to-switch control protocol that enables dynamic configuration of aggregation groups and is standardized by the IEEE802.3ad.
Page 34: Frame Distribution Methods In Link Aggregation
XG2000 series User's Guide 4.4.2 Frame Distribution Methods in Link Aggregation How frames are distributed across physical ports that make up an aggregation group are determined by the contents of a frame (source and destination MAC addresses). There are three ways to specify how frames are distributed: Frame distribution based on destination MAC address (dst-mac) The destination port is determined based on the destination MAC address of the frames.
Page 35: Notes On Link Aggregation
XG2000 series User's Guide 4.4.4 Notes on Link Aggregation The smallest port number in an aggregation group serves as the master port. Port settings established after defining an aggregation group inherit the same settings as those of the master port, with some exceptions.
Page 36: Uplink Filter
XG2000 series User's Guide 4.5 Uplink Filter When an uplink domain is defined, the domain's uplink domain ports filter (drops) multicast, broadcast and unlearned (flooding) unicast frames from non-membership downlink ports. However it does not filter learned unicast frames that are forwarded based on the MAC address table.
Page 37 XG2000 series User's Guide When specifying multiple uplink ports within an uplink domain, frame distribution among the uplink ports is performed equally from port to port and not by type of frame. Frame distribution changes automatically when a fail-over or fail-back occurs, thereby providing uplink redundancy.
Page 38 XG2000 series User's Guide The following is an example of a fat tree configuration with network redundancy. To configure an uplink filter, carry out the following procedures in the administrator EXEC mode. Command Task Switch to global configuration mode. xg# configure terminal Create an uplink domain that consists of port 11 and 12.
Page 39: Spanning Tree Protocol (Stp)
XG2000 series User's Guide 4.6 Spanning Tree Protocol (STP) The Spanning Tree Protocol (STP) is a function that prevents loops from occurring on a network. It is also possible to provide network redundancy by intentionally creating a loop. STP exclusively uses only one active path between network devices, and shuts out other paths, to avoid network loops. An active path is selected by comparing path costs defined on each path.
Page 40: Port Roles Based On Spanning Tree
XG2000 series User's Guide 4.6.1 Port Roles Based on Spanning Tree RSTP assigns one of these port roles to individual ports: Root port Provides the best path (lowest cost) when the switch forwards packets to the root switch. Designated port Connects to the designated switch toward the leaves of the spanning tree.
Page 41: Vlan
XG2000 series User's Guide 4.7 VLAN VLAN (Virtual LAN) is a technology that divides a single network into virtually separated networks. VLANs are separate logical networks within one physical network. A VLAN capable switch can change and define new LAN network configurations without changing physical cable connections.
Page 42: Tag-Based (Ieee802.1Q) Vlan
XG2000 series User's Guide 4.7.2 Tag-Based (IEEE802.1Q) VLAN Tag-based VLAN is a method of configuring VLANs so that the frame forwarding decision is based on a tag in the MAC header identifying the VLAN membership. 4 bytes of additional data in the header, called a VLAN tag, identifies the VLAN frame ownership.
Page 43: Multiple Vlan
XG2000 series User's Guide 4.7.3 Multiple VLAN With the user-defined VLAN tag protocol identifier, the IEEE 802.1Q standard tag can be replaced with a user-defined VPID, allowing for encapsulation of multiple tags for multiple-tagged VLANs. The standard tag identifier or TPID is 0x8100 as defined in IEEE 802.1Q.
Page 44 XG2000 series User's Guide An example of multiple VLAN and the movement of frames for a VLAN member outgoing port (VLAN-tagged frame), is shown below. An example of multiple VLAN and the movement of frames for a VLAN member outgoing port (VLAN-untagged frame), is shown below.
Page 45 XG2000 series User's Guide An example of multiple VLAN and the movement of frames when the user-defined VPID of the incoming and outgoing port differ and the outgoing port is a VLAN member (VLAN-tagged frame), is shown below. An example of multiple VLAN and the movement of frames when the user-defined VPID of the incoming and outgoing port differ and the outgoing port is not a VLAN member (VLAN-untagged frame), is shown below.
Page 46: Quality Of Service (Qos)
XG2000 series User's Guide 4.8 Quality of Service (QoS) The device provides Quality of Service (QoS) that is based on the IEEE802.1p standard. The device QoS determines the priority of frames at the ingress side using DiffServ, VLAN tag (including priority tag) or a port's default priority.
Page 47: Igmp Snooping
The XG2000 series floods IGMP Report messages. When IGMP v1/v2 is used, it is necessary to connect a device, such as a L3 switch, that supports IGMP snooping between the XG2000 series and the IGMP hosts in order to avoid flooding.
Page 48: Registering Group Members
XG2000 series User's Guide 4.9.1 Registering Group Members On receiving an IGMP Report message, the device registers a multicast MAC address with the MAC address table for the port that received the IGMP Report message and the connecting multicast router port.
Page 49: Removing Group Members
XG2000 series User's Guide 4.9.2 Removing Group Members The group members registered by IGMP snooping are removed under the following status. If after receiving an IGMP Report message for group registration, the group member interval expires before the device receives another IGMP Report message, the switch removes that group member. The default setting for the group member interval is 260 seconds.
Page 50: Managing Group Members
XG2000 series User's Guide 4.9.3 Managing Group Members When network congestion causes Leave message loss or there is a host that uses IGMPv1, the multicast router does not receive Leave messages. The multicast router sends out an IGMP General Query message to all hosts (IP address: 224.0.0.1) at intervals (query interval) to determine membership information.
Page 51: Igmp Querier
XG2000 series User's Guide 4.9.4 IGMP Querier In a typical network configuration, the multicast router periodically sends out an IGMP General Query message to determine if any of the hosts on the network are members of any multicast groups. Receiving a response from a host ascertains its membership in a multicast group.
Page 52: Configuring Igmp Snooping
XG2000 series User's Guide 4.9.5 Configuring IGMP Snooping To configure IGMP snooping, carry out the following procedure in the administrator EXEC mode. Command Task Switch to global configuration mode. xg# configure terminal Enable global IGMP snooping on the device. xg(config)# ip snooping protocol igmp Enable IGMP snooping for each VLAN separately.
Page 53: Network Management
XG2000 series User's Guide 4.10 Network Management 4.10.1 Traffic Statistics The device can display traffic statistics to analyze network operations such as traffic bytes, errors, etc. The following are the Traffic Statistics the device provides. Displays traffic information on outgoing and incoming frames for each port.
Page 54: Snmp Agent
XG2000 series User's Guide 4.10.2 SNMP Agent SNMP (Simple Network Management Protocol) is a protocol that monitors and manages devices on a network. The device supports the SNMP (v1/v2c) function to collect management information blocks (MIBs) from a remote network manager (SNMP manager).
Page 55: Radius/Tacacs+ Authentication
XG2000 series User's Guide 4.11 RADIUS/TACACS+ authentication RADIUS (Remote Authentication Dial In User Service) or TACACS (Terminal Access Controller Access Control System) is used to manage authentication, authorization, accounting remotely. XG2000 supports RADIUS/TACACS+ authentication using PAP (User Password) for login authentication. An administrator can unify the authentications of various devices, which support RADIUS/TACACS+ clients functions through a RADIUS/TACACS+ server.
Page 56: Configuring Radius/Tacacs
XG2000 series User's Guide 4.11.3 Configuring RADIUS/TACACS+ To configure RADIUS/TACACS+ authentication, carry out the following procedure. Command Task Switch to global configuration mode. xg# configure terminal (Optional) xg(config)# radius-server key KEY Specifies a global secret key which is used as a default parameter when RADIUS server is registered with no key parameter.
Page 58: About Command Reference
XG2000 series User's Guide 5.1 About Command Reference This section describes how to read command references. 5.1.1 Command System The following is the system of commands provided in the device: Item Function Management LAN Interface Configuration These are used to configure functions related to the management LAN commands interface.
Page 59: Configuration Of Command Reference
XG2000 series User's Guide 5.1.2 Configuration of Command Reference This section describes the configuration of command reference and descriptive content. Function Explains the functions of the commands. Prompt Indicates the prompt of the operational mode. Command syntax Describes the command syntax. The notation of the command syntax is as follows:...
Page 60: Management Lan Interface Configuration Commands
XG2000 series User's Guide 5.2 Management LAN Interface Configuration Commands This section explains configuration commands related to the Management LAN Interface. 5.2.1 show remote-host Function Displays the relationship between the remote hostname and IP address. Prompt xg> or xg# Command syntax...
Page 61: Management-Lan Ip
XG2000 series User's Guide 5.2.2 management-lan ip Function Sets the IP address and default gateway, when the Management LAN Interface is used. Use the no form to disable the Management LAN Interface. Prompt xg(config)# Command syntax management-lan ip A.B.C.D/M [default-gw A.B.C.D]...
Page 62: Management-Lan Dns-Server
XG2000 series User's Guide 5.2.3 management-lan dns-server Function Registers the IP address of a DNS (Domain Name Service) server used for host name resolution. Up to three DNS servers can be registered. Use the no form to delete registered DNS servers.
Page 63: Management-Lan Domain
XG2000 series User's Guide 5.2.4 management-lan domain Function Sets the default domain name when referring to a DNS (Domain Name Service) server. For example, when the host name is "hostname1," and "abc.jp" is specified as the default domain name, perform a search for the address with an FQDN (Fully Qualified Domain Name) of "hostname1.abc.jp."...
Page 64: Hostname
XG2000 series User's Guide 5.2.5 hostname Function Changes the hostname of the device. Use the no form to return to the default ("xg"). Prompt xg(config)# Command syntax hostname HOST-NAME no hostname Parameter HOST-NAME Specifies the hostname of the device. Specify the hostname using 63 characters or less, with an alphabet character at the beginning.
Page 65: Remote-Host
XG2000 series User's Guide 5.2.6 remote-host Function Registers remote host information and shows the relationship between the remote hostname and IP address. By registering the IP address of a remote host that is used frequently, the name can be specified instead of the IP address. The relationship between the registered hostname and IP address is given priority over the DNS server configuration.
Page 66 XG2000 series User's Guide Note If a remote host is registered or deleted, the new setting becomes enabled after executing “copy running-config startup-config” command and restart the device. Example Register the IP address "11.22.33.45" as the hostname of "HOST005," and then "11.22.33.46" as the hostname of "HOST006."...
Page 67: Serial/Telnet/Ssh Configuration Commands
XG2000 series User's Guide 5.3 Serial/Telnet/SSH Configuration Commands This section explains configuration commands related to a serial connection/telnet/SSH connection. 5.3.1 terminal pager Function Enables or disables the pager function of the serial/telnet/SSH terminal. Prompt xg> or xg# Command syntax terminal pager { on | off }...
Page 68: Baud-Rate
XG2000 series User's Guide 5.3.3 baud-rate Function Sets the serial baud rate (bps). Prompt xg(config-line)# Command syntax baud-rate { 9600 | 19200 | 38400 | 57600 } Parameter { 9600 | 19200 | 38400 | 57600 } Specifies any of 9600/19200/38400/57600 as the serial baud rate (bps).
Page 69: Telnet-Server
XG2000 series User's Guide 5.3.5 telnet-server Function Enables telnet connections with the device. Use the no form to disable telnet connections. Prompt xg(config)# Command syntax telnet-server no telnet-server Command type Configuration command Default Disabled Example Enable telnet connections to the device.
Page 70: Show Ssh-Host-Key
XG2000 series User's Guide 5.3.8 show ssh-host-key Function Shows authentication key. Prompt xg> or xg# Command syntax show ssh-host-key Command type Operation management commands Output form xg# show ssh-host-key SSH Host Key 2007/09/07-17:10:33 =============================================================================== ssh-dss AAAAB3NzaC1kc3MAAACBALZunL9ymdBEx4QFOsKhwwCf7WpCwpLne6ZNgc7keG/2Yf0OY4Yx MwOgf1Dm5SSaN/pSdfKotT/zN3ywpDQywlNVjNxF7IYk/p3Q/jABPa245A1Mu9l9a8IiOZhV+w0vMI8N vTi4Cqk2S+tSDzf2vXQ58KCAijeyGDrEi71bZPgbAAAAFQDjkiO5/EupRfrKMc2HHpM7OWtF+QAAAIBR c1CGq9Wt60LV6DkzrYhLNcRgkRNi/XFARzyyFX3TWm2LPBDd8/nbp3zc+N5poNKHBJ/61somWzqKVrTA nR/AQDEyftltVgr4vWn1IDEtu6IZzShZGfgFDk2aZIVP3jFr0BEz5GV+eoGkQb4Be3qJHKiomIjNi+As...
Page 71: Clear Ssh-Rhost-Key
XG2000 series User's Guide 5.3.10 clear ssh-rhost-key Function Delete registered public key of SSH remote host. Prompt Command syntax clear ssh-rhost-key [ HOST ] Parameter HOST Specifies the host name or IP address of a SSH server. If this parameter is omitted, all public keys will be deleted.
Page 72: Terminal Window
XG2000 series User's Guide 5.3.12 terminal window Function Sets the screen display size of the serial connection terminal. Use the no form to return to the default setup. For a telnet or SSH connection, the screen size will be obtained automatically from the client terminal.
Page 73: System Basic Operation Commands
XG2000 series User's Guide 5.4 System Basic Operation Commands This section explains the basic commands of the device CLI (Command Line Interface). 5.4.1 enable Function Switches from the operator exec mode to the administrator exec mode. When a password is set for the "enable" command, a password is required. When there is an error in entering the password, re-entering the password will be allowed up to three times.
Page 74: Show History
XG2000 series User's Guide 5.4.2 show history Function Displays the history of executed commands since logged into the device. Prompt xg> or xg# Command syntax show history Command type Operation management commands Output form xg# show history 1 enable 2 show system information...
Page 75: Configure Terminal
XG2000 series User's Guide 5.4.4 configure terminal Function Switch from the administrator exec mode to the global configuration mode. Prompt Command syntax configure terminal Command type Operation management commands Message Configuration is locked by other. Explanation A switch in state is not possible because a terminal session in global configuration mode exists.
Page 76: Logout / Quit
XG2000 series User's Guide 5.4.6 logout / quit Function Logs out and disconnects the terminal session. Prompt xg> or xg# Command syntax Logout Command type Operation management commands Example Log out and disconnect the terminal session. xg# logout Connection closed by foreign host.
Page 77: Help
XG2000 series User's Guide 5.4.8 help Function Displays help on how to use the CLI. Prompt xg>, xg#, xg(config)# , xg(config-if)# , xg(config-agg)# , xg(config-vlan)# , xg(config-line)# Command syntax Help Command type Operation management commands 5.4.9 show account Function Displays information about the user.
Page 78: Account
XG2000 series User's Guide 5.4.10 account Function Create a new user. Use the no form to delete the specified user. Prompt Command syntax account USERNAME class { operator | admin } no account USERNAME Parameter USERNAME Specify a username with a length in the range of 2 to 16 characters, with an alphabet character at the beginning.
Page 79: Password (Operator Exec Mode)
XG2000 series User's Guide Note Specify a password with a length in the range of 5 to 16 characters. The maximum number of users that can register to this device is 4. Example Add user0001 as the username and specify operator class:...
Page 80: Password (Administrator Exec Mode)
XG2000 series User's Guide 5.4.12 password (Administrator EXEC mode) Function Change the login password of the device. Prompt Command syntax password [USERNAME] Parameter USERNAME Specify the username to change its login password. When USERNAME is omitted, the login password of own user is changed.
Page 81: Reset
XG2000 series User's Guide 5.4.13 reset Function Restarts the device. Prompt Command syntax reset [ factory-default ] Parameter [ factory-default ] When this parameter is specified, the contents of startup-config, log, and login password will be returned to the factory default.
Page 82: Date
XG2000 series User's Guide 5.4.15 date Function Displays the date/time of the current system clock. Prompt xg> or xg# Command syntax Date Command type Operation management commands Output form The current date and time is displayed in the form of "year/month/date-hour:minutes:seconds."...
Page 83: Date Timezone
XG2000 series User's Guide 5.4.17 date timezone Function Sets the time zone of the device. Use the no form to return to the default setup. Prompt Command syntax Date timezone gmt OFFSET No date timezone Parameter gmt [ OFFSET ] Specifies the time zone as the difference from GMT (Greenwich Mean Time).
Page 84: Date Summer-Time
XG2000 series User's Guide 5.4.18 date summer-time Function Sets Daylight Saving Time. Use the no form to return to the default setup. Prompt Command syntax date summer-time START_DAY[/TIME] END_DAY[/TIME] [OFFSET] no date summer-time Parameter START_DAY[/TIME] Specifies the day/time to start Daylight Saving Time in any form of "Mm.w.d/hhmm," "Jn/hhmm,"...
Page 85 XG2000 series User's Guide Message % DATE '%1$' is invalid Explanation The specified date/time is incorrect. [[Inserted string]]%1$: incorrect parameter value is displayed. Solution Correct the error in the parameter, and execute the command again. % OFFSET '%1$' is invalid Explanation The specified OFFSET is incorrect.
Page 86: Ping
XG2000 series User's Guide 5.4.19 ping Function Checks if communication with the specified host is possible by sending ICMP Echo Request packets to a specified host from the manage LAN interface and observing the reception of ICMP Echo Reply packets.
Page 87: Enable Password
XG2000 series User's Guide 5.4.20 enable password Function Sets the password for the enable command. Use the no form to disable the password protection. Prompt xg(config)# Command syntax enable password no enable password Parameter password Specifies the password to associate with the enable command.
Page 88: Banner
XG2000 series User's Guide 5.4.21 banner Function Sets the banner string to be displayed when logging in to the device. Use the no form to delete the banner string. Prompt xg(config)# Command syntax banner login LINE banner login default no banner...
Page 89: Ntp-Server
XG2000 series User's Guide 5.4.22 ntp-server Function Synchronizes the system time to a specified NTP server’s time, using NTP (Network Time Protocol) Version3. Up to four NTP servers can be registered. Use the no form to return the setting to its default.
Page 90: Radius/Tacacs
XG2000 series User's Guide 5.5 RADIUS/TACACS+ This section explains the commands related to RADIUS/TACACS+. 5.5.1 show authentication Function Displays the setting status of authentication method. Prompt Command syntax show authentication Command type Operation management commands. Output form xg# show authentication...
Page 91: Aaa Authentication Login
XG2000 series User's Guide 5.5.2 aaa authentication login Function Configure login authentication method. Use the no form to return to the default setup. Prompt xg(config)# Command syntax aaa authentication login { console | ssh } { local | radius | tacacs } [{ local |...
Page 92: Show Radius
XG2000 series User's Guide 5.5.3 show radius Function Displays the information of RADIUS server. Prompt Command syntax show radius Command type Operation management command Output form xg# show radius RADIUS Information 2008/05/20-16:26:00 ================================================================================ Global Parameters =============================================== Secret Key : radius-b1...
Page 93: Radius-Server Host
XG2000 series User's Guide 5.5.4 radius-server host Function Registers a RADIUS server. Up to four RADIUS servers can be registered. Use the no form to delete registered RADIUS servers. Prompt xg(config)# Command syntax radius-server host HOST [ auth-port <1 - 65535> ] [ key KEY ]...
Page 94: Radius-Server Key
XG2000 series User's Guide 5.5.5 radius-server key Function Specifies a global secret key which is used as a default parameter when the RADIUS server is registered without secret key. Use the no form to delete a global secret key. Prompt...
Page 95: Radius-Server Timeout
XG2000 series User's Guide 5.5.6 radius-server timeout Function Specifies timeout for access replay from a RADIUS server. Use the no form to return the setting to its default. Prompt xg(config)# Command syntax radius-server timeout <1 – 15> no radius-server timeout Parameter timeout <1 - 15>...
Page 96: Show Tacacs
XG2000 series User's Guide 5.5.7 show tacacs Function Displays the information of TACACS+ server. Prompt Command syntax show tacacs Command type Operation management command Output form xg# show tacacs TACACS+ Information 2008/06/18-12:12:15 ================================================================================ Global Parameters =============================================== Secret Key : tacacs-b1...
Page 97: Tacacs-Server Host
XG2000 series User's Guide 5.5.8 tacacs-server host Function Registers a TACACS+ server. Up to four TACACS+ servers can be registered. Use the no form to delete registered TACACS+ servers. Prompt xg(config)# Command syntax tacacs-server host HOST [ key KEY ]...
Page 98: Tacacs-Server Key
XG2000 series User's Guide 5.5.9 tacacs-server key Function Specifies a global secret key which is used as a default parameter when the TACACS+ server is registered without secret key. Use the no form to delete a global secret key. Prompt...
Page 99: Configuration File Operation Commands
XG2000 series User's Guide 5.6 Configuration File Operation Commands This section explains the commands related to configuration files and file operations within volatile memory. 5.6.1 copy running-config startup-config Function Stores the configuration file (running-config) in volatile memory to the startup-config file in nonvolatile memory.
Page 100: Show Running-Config (Redirect)
XG2000 series User's Guide 5.6.3 show running-config (redirect) Function Copies the configuration information (running-config) in the currently operating volatile memory to the volatile memory. Also, it can be copied directly to a file in the remote server using the "tftp" or "scp" command.
Page 101 XG2000 series User's Guide % Invalid IP-address. Explanation The specified format of the IP address or specified content is incorrect. Solution Specify the IP address in a correct format and execute it again. % Cannot find %1$ Explanation An incorrect host name was specified.
Page 102 XG2000 series User's Guide %1$: invalid user name Explanation Specified username is invalid. [[Inserted string]]%1$: Specified username. Solution Specify the correct username. % Cannot create output file %1$ Explanation There is not enough free space to create output file on the device. A temporary file may remain on the device.
Page 103: Show Startup-Config
XG2000 series User's Guide 5.6.4 show startup-config Function Displays the configuration information (startup-config) stored in the nonvolatile memory of the device. Prompt Command syntax show startup-config Command type Operation management commands Example Display the content of startup-config. xg# show startup-config...
Page 104: Show Startup-Config (Redirect)
XG2000 series User's Guide 5.6.5 show startup-config (redirect) Function Copies the startup-config file stored in nonvolatile memory to volatile memory. The configuration file can also be copied directly to a file on a remote server using the "tftp" or “scp” command.
Page 105 XG2000 series User's Guide % Invalid IP-address. Explanation The specified format of the IP address or specified content is incorrect. Solution Specify the IP address in a correct format and execute the command again. % Cannot find %1$ Explanation An incorrect host name was specified.
Page 106 XG2000 series User's Guide %1$: invalid user name Explanation Specified username is invalid. [[Inserted string]]%1$: Specified username. Solution Specify the correct username. % Cannot create output file %1$ Explanation There is not enough free space to create output file on the device. A temporary file may remain on the device.
Page 107: Copy Startup-Config
XG2000 series User's Guide 5.6.6 copy startup-config Function Saves the configuration information stored in volatile memory to nonvolatile memory as startup-config. Also, startup-config can be loaded from a remote server using the "tftp" or “scp” command. After executing this command, it is necessary to restart the system using the "reset" command in order for the new startup-config to take effect.
Page 108 XG2000 series User's Guide % tftp: server says: %1$ Explanation An error was received from the TFTP server. [[Inserted string]]%1$: content of error message received from the TFTP server. The content of message depends on the type of TFTP server. For example: −...
Page 109 XG2000 series User's Guide ssh: connect to host %1$ port 22: Network is unreachable Explanation It failed to access to specified SSH server. [[Inserted string]]%1$: Specified IP address or host name. Solution Specify the correct IP address or host name.
Page 110: Dir/Ls
XG2000 series User's Guide 5.6.7 dir/ls Function Lists the files in the volatile memory of the device. Prompt Command syntax Command type Operation management commands Output form xg# dir Update-time File-size File-name - 2007/01/22 19:23:03 system_info_20070122 - 2007/01/22 19:22:41 2,604...
Page 111: Delete
XG2000 series User's Guide 5.6.8 delete Function Deletes the files in the volatile memory of the device. Prompt Command syntax delete FILE-NAMES Parameter FILE-NAMES Specifies the name of the file to delete in the volatile memory. Specify a generic designation with "*" (asterisk) for the file name, and files whose "*"...
Page 112: Rename
XG2000 series User's Guide 5.6.9 rename Function Changes the file names in volatile memory. Prompt Command syntax rename FROM-NAME TO-NAME Parameter FROM-NAME Specifies the file name to change. TO-NAME Specifies the new file name. Follow the rules below in specifying file names: −...
Page 113: Tftp Get
XG2000 series User's Guide 5.6.10 tftp get Function Downloads files on the TFTP server into volatile memory. Prompt Command syntax tftp get HOST REMOTE-FILE [ LOCAL-FILE ] Parameter HOST Specify the hostname of the TFTP server or IP address. IP addresses that can be specified are: 1.0.0.1 - 126.255.255.254, 128.0.0.1 - 191.255.255.254, and 192.0.0.1 - 223.255.255.254.
Page 114 XG2000 series User's Guide Example Copy the file "start_conf_20070122"on the TFTP server "host1", to the device using the file name "start_conf". Then, check whether the file size of the file imported with the "tftp" command is consistent with the original using the dir/(ls) command.
Page 115: Scp Get
XG2000 series User's Guide 5.6.11 scp get Function Downloads files on the SSH server into volatile memory. Prompt Command syntax scp get USERNAME HOST REMOTE-FILE [ LOCAL-FILE ] Parameter USERNAME Specifies the username of the SSH server. HOST Specify the hostname of the SSH server or IP address.
Page 116 XG2000 series User's Guide ssh: connect to host %1$ port 22: Connection refused Explanation It failed to access to specified SSH server. [[Inserted string]]%1$: Specified IP address or host name. Solution Specify the correct IP address or host name. ssh: connect to host %1$ port 22: connection timed out Explanation It failed to access to specified SSH server.
Page 117: Tftp Put
XG2000 series User's Guide 5.6.12 tftp put Function Uploads the files in volatile memory to the TFTP server. Prompt Command syntax tftp put HOST LOCAL-FILE [ REMOTE-FILE ] Parameter HOST Specify the hostname of the TFTP server or IP address.
Page 118: Scp Put
XG2000 series User's Guide 5.6.13 scp put Function Uploads the files in volatile memory to the SSH server. Prompt Command syntax scp put USERNAME HOST LOCAL-FILE [ REMOTE-FILE ] Parameter USERNAME Specifies the username of the SSH server. HOST Specify the hostname of the SSH server or IP address.
Page 119 XG2000 series User's Guide ssh: connect to host %1$ port 22: Connection refused Explanation It failed to access to specified SSH server. [[Inserted string]]%1$: Specified IP address or host name. Solution Specify the correct IP address or host name. Check the setting and status of SSH server and whether there is no problem in network connection to the SSH server.
Page 120: Switch Basic Configuration Commands
XG2000 series User's Guide 5.7 Switch Basic Configuration Commands This section explains configuration commands related to general operation of the switch. 5.7.1 clear bridge mac-address-table Function Deletes dynamically-learned MAC addresses from the MAC address table. Prompt Command syntax #clear bridge mac-address-table dynamic { all | port <1-20> | agg-port <1-10> } Parameter dynamic { all | port <1-20>...
Page 121: Show Bridge
XG2000 series User's Guide 5.7.2 show bridge Function Displays the basic function configuration of the switch. Prompt xg> or xg# Command syntax show bridge Command type Operation management commands Output form xg# show bridge Switch Basic Information 2007/01/22-12:12:15 =============================================================================== Aging Time : {Disabled | <10-1756>...
Page 122: Show Bridge Mac-Address-Table
XG2000 series User's Guide 5.7.3 show bridge mac-address-table Function Displays the MAC address information registered in the MAC address table. Prompt xg> or xg# Command syntax show bridge mac-address-table [ { static | dynamic | igmp-snooping | port <1-20> | agg-port <1-10> | vlan <1-4094>...
Page 123: Bridge Forward-Mode
XG2000 series User's Guide Example Display the content of all MAC address tables. xg# show bridge mac-address-table Mac Address Table Information 2007/01/22-12:12:15 =================================================================== Static Mac-address Table ------------------------------------------------------------------- Mac-address Vlan-id Destination-port -------------- -------- -------------------- 0001.123a.4321 vlan-1 port 2 0002.123a.4321 vlan-1 port 4 0003.123a.4321 vlan-3...
Page 124: Bridge Jumbo-Frame
XG2000 series User's Guide 5.7.5 bridge jumbo-frame Function Sets the maximum frame size of jumbo frames. The maximum frame size that can be forwarded is 16128 byte. Use the no form to disable jumbo frame. Prompt xg(config)# Command syntax bridge jumbo-frame [ { 9216 | 12288 | 15360 | 16128 } ]...
Page 125: Bridge Learn-Mode
XG2000 series User's Guide 5.7.6 bridge learn-mode Function Sets the MAC address table learning mode. The device supports two learning modes: SVL (Shared Vlan Learning) and IVL (Independent VLAN Learning). SVL (Shared VLAN Learning) Regardless of the VLAN of frame ownership, it is learned as a MAC address entry (mapping of MAC address to port) common to every VLAN.
Page 126: Bridge Mac-Address-Table
XG2000 series User's Guide 5.7.7 bridge mac-address-table Function By registering static MAC addresses to the MAC address table, frames with specific destination MAC addresses can be forwarded to a specified port. When a unicast static MAC address is registered, dynamic MAC addresses will not be learned, even when frames sent from the same MAC address are received from a different port.
Page 127 XG2000 series User's Guide % Vlan id is not found. vid=%1$ Explanation The specified VLAN is not created. [[Inserted string]]%1$: VLAN ID Solution Review the vlan specified then execute the command again. % Port is not vlan member. port %1$ vid=%2$ Explanation The port is not a member of the specified VLAN.
Page 128: Bridge Mac-Address-Table Filter
XG2000 series User's Guide 5.7.8 bridge mac-address-table filter Function By registering a MAC address to filter, a frame with a specific destination MAC address will be discarded. When filtering of a MAC address is specified, dynamic learning of the MAC address will not be performed, even when frames sent from the same MAC address are received on a different port.
Page 129: Bridge Aging-Time
XG2000 series User's Guide Note The maximum number of unicast MAC addresses or multicast MAC addresses that can be statically registered to the device are 128 addresses for each type of address including filtered addresses also included in these. Additionally, since MAC addresses are managed with a hash table, a message saying an address cannot be registered may be displayed before reaching the maximum number.
Page 130: Link Aggregation Configuration Commands
XG2000 series User's Guide 5.8 Link Aggregation Configuration Commands This section explains the commands associated with link aggregation. 5.8.1 show link-aggregation Function Displays the state of an aggregation group. Prompt xg> or xg# Command syntax show link-aggregation [ agg-port <1-10> ] Parameter agg-port <1-10>...
Page 131 XG2000 series User's Guide Protocol The control protocol utilized by the link aggregation group is displayed. − None A static link aggregation group. − LACP - Active Uses LACP as the control protocol for link aggregation in Active mode. −...
Page 132 XG2000 series User's Guide Output form (in case of LACP link aggregation) xg# show link-aggregation Link Aggregation Information 2005/04/24-16:16:36 =============================================================================== System Priority : 32768 System ID : 0080.17c2.05e2 ------------------------------------------------------------------------------- [agg-port 1] Master port : port <1-20> Management packet send port : port <1-20>...
Page 133 XG2000 series User's Guide Synchro State The synchronization status of the port is displayed. − Sync The link state of LACP with the destination device connection is in a synchronized state. − No Sync The link state of LACP with the destination device connection is not in a synchronized state.
Page 134: Link-Aggregation
XG2000 series User's Guide 5.8.2 link-aggregation Function Link aggregation is a function wherein multiple ports within a switch act as one logical link (aggregated group). This command is used to set up a link aggregation group. There are two types of link aggregation: static link and LACP.
Page 135 XG2000 series User's Guide distribution-parameter <0-3> Specifies a parameter used in calculating of frame distribution method. When this parameter is omitted, "0" is assumed. Under certain circumstances, load balance bias may not be resolved, when the distribution method is changed. By changing the distribution parameter value, the bias can be minimized.
Page 136: Lacp System-Priority
XG2000 series User's Guide Note Among the ports belonging to an aggregation group, the port with the smallest port number will be the master port. Ports added to an aggregation group immediately after a link aggregation group is initially created will inherit the same settings as that of the master port.
Page 137: Lacp Port-Priority
XG2000 series User's Guide 5.8.4 lacp port-priority Function Sets the priority of LACP ports. The LACP port priority is used as information for identifying ports via LACP. Typically, it is not necessary to change its value from the default. Use the no form to return to the default setup.
Page 138: Uplink Filter Commands
XG2000 series User's Guide 5.9 Uplink Filter Commands This section explains the commands related to uplink filter configuration. 5.9.1 show uplink Function Display the configuration of uplink domains and the state of downlink member ports. Prompt xg>, or xg# Command syntax...
Page 139: Uplink-Domain
XG2000 series User's Guide 5.9.2 uplink-domain Function Create an uplink domain and assign member uplink ports. Use the no form to release the domain membership. Prompt xg(config)# Command syntax uplink-domain <1-20> port <1-20> [ <1-20> no uplink-domain <1-20> Parameter uplink-domain <1-20>...
Page 140 XG2000 series User's Guide Example The following is an example of configuring port 3 and 4 as uplink ports of domain 3, and then, displaying the uplink domain information by using "show" command. xg(config)# uplink-domain 3 port 3 4 xg# show uplink...
Page 141: Downlink Allowed Uplink-Domain
XG2000 series User's Guide 5.9.3 downlink allowed uplink-domain Function Configure the downlink ports belonging to the uplink domain. Use the no form to release the membership. Prompt xg(config-if)#, or xg(config-agg)# Command syntax downlink allowed uplink-domain { <1-20> | all } no downlink allowed uplink-domain { <1-20>...
Page 142: Switch Port Configuration Commands
XG2000 series User's Guide 5.10 Switch Port Configuration Commands This section explains the port specific commands of the switch. 5.10.1 show interface Function Displays the port state of the specified switch. Prompt xg> or xg# Command syntax show interface [ { port <1-20> | agg-port <1-10> } ] Parameter port <1-20>...
Page 143 XG2000 series User's Guide Link Status Detail Details of the port are displayed: Display Meaning PLUG-OUT The XFP is not installed. LOW-PWR The XFP is in low power state. Access to the XFP failed. The shutdown command was executed. Since the shutdown command and link-aggregation command were executed, the port is down for a certain period of time.
Page 144 XG2000 series User's Guide Vlan Information Port Default Vlan ID The default VLAN ID of the port is displayed. Vlan Member (tagged frame) Registered VLAN membership (tagged), is displayed. If not registered as a VLAN member (tagged), "None" is displayed.
Page 145: Show Port-Description
XG2000 series User's Guide 5.10.2 show port-description Function Displays information about port description. Prompt xg> or xg# Command syntax show port-description Command type Operation management commands. Output form xg# show port-description Port Description Information 2007/05/10-17:50:54 =============================================================================== [agg-port 1] Description: agg_name1...
Page 146: Shutdown (Administrator Exec Mode)
XG2000 series User's Guide 5.10.3 shutdown (Administrator exec mode) Function Shuts down the port of a switch from the administrator exec mode, and turns off the optical signal at the XFP. Use the no form to enable the port again.
Page 147: Interface Port
XG2000 series User's Guide 5.10.5 interface port Function Switches from the global configuration mode to the interface edit mode wherein ports are configured. Multiple ports can be configured collectively. Prompt xg(config)# Command syntax interface port <1-20> [ <1-20> ] interface port range <1-20> <1-20>...
Page 148: Description
XG2000 series User's Guide 5.10.6 description Function Describes the port information. Use the no form to delete the port description. Prompt xg(config-if)# or xg(config-agg)# Command syntax description DESCRIPTION no description Parameter description_DESCRIPTION Describes the port information using ASCII characters. The description can be up to 64 alphanumeric characters in length.
Page 149: Flowcontrol
XG2000 series User's Guide 5.10.7 flowcontrol Function Configures PAUSE flow control . Use the no form to return to the default setup. Prompt xg(config-if)# or xg(config-agg)# Command syntax flowcontrol { disable | only-receive | | only-send | send-receive } no flowcontrol...
Page 150: Storm-Control
XG2000 series User's Guide 5.10.8 storm-control Function Enables broadcast storm control for the designated ports. Use the no form to disable storm control. Prompt xg(config-if)# or xg(config-agg)# Command syntax storm-control no storm-control Command type Configuration command Default None Note When a broadcast storm condition is detected, the port will be in a violation state. After eliminating the cause of the condition, clear the violation state with the "clear violation"...
Page 151: Shutdown (Interface Edit Mode)
XG2000 series User's Guide 5.10.10 shutdown (Interface edit mode) Function Shuts down the ports so that they cannot be used. Use the no form to enable the ports again. Prompt xg(config-if)# or xg(config-agg)# Command syntax shutdown no shutdown Command type...
Page 152: Port-Security
XG2000 series User's Guide 5.10.12 port-security Function Sets port security based on the source MAC address. When port security is enabled, register the MAC addresses permitted using the "bridge mac-address-table" command. Use the no form to disable port security. Prompt...
Page 153: Link-Pass-Through
XG2000 series User's Guide 5.10.13 link-pass-through Function Link pass through is a function that monitors the link state of a specific port, and, by synchronizing the link state of the specified port, promptly notifies changes of the link state to devices connected to the notification (domino) port.
Page 154: Ingress-Bandwidth
XG2000 series User's Guide 5.10.14 ingress-bandwidth Function Sets the ingress rate limiting value for the designated ports. When reception traffic exceeds the ingress rate limiting value, received frames will be discarded. Use the no form to return to the default setup.
Page 155: Multicast-Forwarding
XG2000 series User's Guide 5.10.15 multicast-forwarding Function Sets the forwarding method for multicast frames. Use the no form to return to the default setup. Prompt xg(config)# or xg(config-agg)# Command syntax multicast-forwarding { forward-all | forward-unregistered-mac | filter-unregistered-mac } no multicast-forwarding...
Page 156: Spanning Tree Protocol (Stp) Configuration Commands
XG2000 series User's Guide 5.11 Spanning Tree Protocol (STP) Configuration Commands This section explains the commands related to the Spanning Tree Protocol. 5.11.1 show spanning-tree Function Displays the state of the Spanning Tree Protocol. Prompt xg> or xg# Command syntax show spanning-tree [ detail [ { port <1-20>...
Page 157 XG2000 series User's Guide Switch Information for Spanning Tree General Spanning Tree Protocol information is displayed. Spanning Tree The operational state of the Spanning Tree Protocol is displayed. − Disabled Spanning Tree Protocol is disabled. − Enabled Spanning Tree Protocol is enabled.
Page 158 XG2000 series User's Guide Mode The switch port mode of the Spanning Tree Protocol is displayed. − The switch port is operating in STP (IEEE 802.1D Spanning Tree Protocol) mode. − RSTP The switch port is operating in RSTP (IEEE 802.1w Rapid Spanning Tree Protocol) mode.
Page 159 XG2000 series User's Guide Output form (detailed display) xg# show spanning-tree detail Spanning Tree Information 2007/01/22-12:12:15 =============================================================================== Switch Information for Spanning Tree --------------------------------------------------------------- Spanning Tree : {Enable | Disable} Root Switch Priority: 32768 Root Switch ID : 8000.0080.17C2.0511 Root Path Cost...
Page 160 XG2000 series User's Guide Link Type Indicates the state of the current link. − Point-to-point A point-to-point link. − Shared A shared link. Forward-Transitions Displays the number of times the port changed to forwarding state. Portfast The Portfast state is displayed.
Page 161: Spanning-Tree
XG2000 series User's Guide 5.11.2 spanning-tree Function Enables the Spanning Tree Protocol (STP). Use the no form to disable Spanning Tree Protocol. Prompt xg(config)# Command syntax spanning-tree no spanning-tree Command type Configuration command Default None Message % port %1$ is membership of uplink-domain %2$.
Page 162: Spanning-Tree Priority
XG2000 series User's Guide 5.11.3 spanning-tree priority Function Sets the switch priority of the Spanning Tree Protocol. Whichever switch priority is smallest is selected as the root switch for the Spanning Tree. Use the no form to return to the default state.
Page 163: Spanning-Tree Hello-Time
XG2000 series User's Guide 5.11.4 spanning-tree hello-time Function The hello time is a time interval between BPDUs. Periodic BPDUs inform all the other switches on the network of the root switch routing information. Use the no form to return to the default setup.
Page 164: Spanning-Tree Max-Age
XG2000 series User's Guide 5.11.5 spanning-tree max-age Function The maximum age (max-age) of the Spanning Tree is the maximum valid time interval between received BPDUs. When BPDUs are not received within that time, the topology of the Spanning Tree will be recalculated, and the switch that timed out will send BPDUs acting as a root switch.
Page 165: Spanning-Tree Forward-Time
XG2000 series User's Guide 5.11.6 spanning-tree forward-time Function The forward delay time of the Spanning Tree is the time required for the ports to change to a forwarding state. Use the no form to return to the default setup. Prompt...
Page 166: Spanning-Tree Port-Priority
XG2000 series User's Guide 5.11.7 spanning-tree port-priority Function Sets a port priority within the Spanning Tree. A smaller value has a higher priority. Use the no form to return to the default setup. Prompt xg(config-if)# or xg(config-agg)# Command syntax spanning-tree port-priority <0-240>...
Page 167: Spanning-Tree Path-Cost-Default
XG2000 series User's Guide 5.11.9 spanning-tree path-cost-default Function Sets the version of path cost (IEEE802.1D: 16bits or IEEE802.1D:32bits) to be used for the Spanning Tree Protocol. Use the no form to return to the default setup. Prompt xg(config)# Command syntax...
Page 168: Spanning-Tree Portfast
XG2000 series User's Guide 5.11.10 spanning-tree portfast Function The “portfast” function reduces the transition time required to transition to a "Forwarding" state. When the function is enabled, the port state is directly changed from "Discarding" to "Forwarding" and does not transition to a "Listening" or Learning" state.
Page 169: Spanning-Tree Portfast Bpdu-Guard
XG2000 series User's Guide 5.11.11 spanning-tree portfast bpdu-guard Function Enable the BPDU guard function for a port within portfast enabled. When BPDU guard enabled port receives a BPDU, the port is shut down and its communication fails. During this time, the received BPDU is not processed.
Page 170: Spanning-Tree Portfast Bpdu-Filter
XG2000 series User's Guide 5.11.13 spanning-tree portfast bpdu-filter Function Enable the BPDU filter for a portfast enabled port. If BPDU filtering in enabled, the port does not send or receive a BPDU. Use the no form to return to the default setup.
Page 171: Virtual Lan (Vlan) Setup Commands
XG2000 series User's Guide 5.12 Virtual LAN (VLAN) Setup Commands This section explains the configuration commands related to Virtual LANs (VLAN). 5.12.1 show vlan Function Displays information about available VLANs and their member ports. Prompt xg> or xg# Command syntax show vlan [ <1-4094>...
Page 172: Vlan
XG2000 series User's Guide 5.12.2 vlan Function Creates a VLAN. Also, a VLAN description may be specified to allow easy identification. Up to 128 VLANs can be created. Use the no form to delete the VLAN. Prompt xg(config)# Command syntax vlan <1-4094>...
Page 173: Interface Vlan
XG2000 series User's Guide 5.12.3 Interface vlan Function Switches from the global configuration mode to the interface edit mode wherein VLANs are configured. Multiple VLANs can be configured collectively. Prompt xg(config)# Command syntax interface vlan <1-4094> [ <1-4094> ] Parameter vlan <1-4094>...
Page 174: Egress
XG2000 series User's Guide 5.12.4 egress Function Registers a port as a VLAN member. Use the no form to release the VLAN membership. Prompt xg(config-vlan)# Command syntax egress { untagging | tagging } { port <1-20> | agg-port <1-10> } no egress { port <1-20>...
Page 175: Port-Vlan-Id
XG2000 series User's Guide 5.12.5 port-vlan-id Function The port-vlan-id command allows assigning a port to explicitly belong to a VLAN and configure the VLAN as a group of ports. However, when a frame with VLAN tags is received, the VLAN tag information has precedent over the port VID.
Page 176: Vlan-Member Allowed
XG2000 series User's Guide 5.12.6 vlan-member allowed Function Registers a port as a VLAN member. Use the no form to release the VLAN membership. Prompt xg(config-if)# or xg(config-agg)# Command syntax vlan-member allowed vlan { <1-4094> | all } { egress-untagging | egress-tagging } no vlan-member allowed vlan { <1-4094>...
Page 177: User-Vlan-Protocol-Id
XG2000 series User's Guide 5.12.7 user-vlan-protocol-id Function The VLAN tag protocol ID (VPID or TPID) used for VLAN tag identification can be changed to the user-defined value of each port. The standard VLAN tag protocol ID was defined as 0x8100 in IEEE 802.1Q. However, the standard IEEE 802.1Q tag for multiple-tag VLAN encapsulated with the user-defined VPID (or TPID) tag (*) can be used.
Page 178: Ingress-Filter Tagged-Frame
XG2000 series User's Guide 5.12.9 ingress-filter tagged-frame Function Specifies that designated port VLAN-tagged frames will be discarded. Use the no form to disable frame discarding. Prompt xg(config-if)# or xg(config-agg)# Command syntax ingress-filter tagged-frame no ingress-filter tagged-frame Parameter tagged-frame Discards VLAN-tagged frames when they are received.
Page 179: Vlan-Statistics Collection
XG2000 series User's Guide 5.12.11 vlan-statistics collection Function Configures the specified VLANs to collect statistics information. Up to 32 VLANs can be set. Use the no form to cancel collecting the VLAN statistics information. Prompt xg(config)# Command syntax vlan-statistics collection <1-4094> [ <1-4094>...
Page 180: Qos Setup Commands
XG2000 series User's Guide 5.13 QoS Setup Commands This section explains the Quality of Service (QoS) configuration commands. 5.13.1 show qos Function Displays the current Quality of Service (QoS) status. Prompt xg> or xg# Command syntax show qos [ qos-map ]...
Page 181: Qos Default-Priority
XG2000 series User's Guide 5.13.2 qos default-priority Function Sets the default priority for frames having no priority information (such as VLAN untagged frames). Use the no form to return to the default setup. Prompt xg(config-if)# or xg(config-agg)# Command syntax qos default-priority <0-7>...
Page 182: Bridge Diffserv-Tos
XG2000 series User's Guide 5.13.4 bridge diffserv-tos Function Enables Quality of Service using the DiffServ code point. When priority control by DiffServ codes is enabled, any priority included in a VLAN tag and the default priority are ignored. Use the no form to disable DiffServ code control.
Page 183: Qos Egress-Scheduling
XG2000 series User's Guide 5.13.5 qos egress-scheduling Function Sets the egress scheduling algorithm. Use the no form to reset to default. Prompt xg(config-if)# or xg(config-agg)# Command syntax qos egress-scheduling {strict | drr | drr-strict} no qos egress-scheduling Parameter egress-scheduling Specify the egress scheduling algorithm −...
Page 184: Qos Bandwidth
XG2000 series User's Guide 5.13.6 qos bandwidth Function Sets a band width value for an output queue. Each output queue can be assured sufficient output traffic rate. Use the no form to reset to default. Prompt xg(config-if)# or xg(config-agg)# Command syntax qos bandwidth <0-10000>...
Page 185: Port Mirroring Setup Commands
XG2000 series User's Guide 5.14 Port Mirroring Setup Commands This section explains the configuration commands for port mirroring. 5.14.1 show mirror Function Displays the current mirroring configuration for send and receive frames. Prompt xg> or xg# Command syntax show mirror...
Page 186: Mirror
XG2000 series User's Guide 5.14.2 mirror Function Configures port mirroring for specific ports. Use the no form to cancel the port mirroring setup. Prompt xg(config)# Command syntax mirror monitored-port <1-20> [rx-mirroring-port <1-20>] [tx-mirroring-port <1-20>] no mirror Parameter monitored-port <1-20> Specifies a port number to be monitored.
Page 187: Igmp Snooping Setup Commands
XG2000 series User's Guide 5.15 IGMP Snooping Setup Commands This section explains the IGMP snooping configuration commands. 5.15.1 show ip snooping Function Displays the IGMP snooping configuration. Prompt xg> or xg# Command syntax show ip snooping [vlan <1-4094> ] show ip snooping mrouter [vlan <1-4094>] show ip snooping group [vlan <1-4094>]...
Page 188 XG2000 series User's Guide [vlan 1] The VIDs of applicable VLANs are displayed. IGMP snooping The IGMP operational state for the applicable VLANs are displayed. − Enabled IGMP snooping is enabled. − Disabled IGMP snooping is disabled. Registered group number The number of registered multicast groups detected through IGMP snooping are displayed.
Page 189: Ip Snooping Protocol
XG2000 series User's Guide Output form (if “mrouter” is specified) Only the multicast router information is extracted from the IGMP snooping information and displayed. xg# show ip snooping mrouter IGMP Snooping Information(Multicast Router) 2005/04/24-22:19:52 =============================================================================== Vlan Type Mrouter ports ---- ------- -------------...
Page 190: Ip Snooping Vlan
XG2000 series User's Guide 5.15.3 ip snooping vlan Function Enables IGMP snooping for a specified VLAN. IGMP snooping can be enabled for each VLAN only after enabling global IGMP snooping using the “ip snooping protocol” command. Use the no form to return to the default setup.
Page 191: Ip Snooping Vlan Max-Group
XG2000 series User's Guide 5.15.4 ip snooping vlan max-group Function Defines the number of multicast groups that can be registered for IGMP snooping on each VLAN. Use the no form to return to the default setup. Prompt xg(config)# Command syntax ip snooping vlan <1-4094>...
Page 192: Ip Snooping Vlan Mrouter
XG2000 series User's Guide 5.15.5 ip snooping vlan mrouter Function Automatically learns the IGMP query message receiving port as a multicast router port. This command can statically set multicast router ports. Also, it can change the automatic learning mode of multicast router ports.
Page 193: Ip Snooping Vlan Group-Member-Interval
XG2000 series User's Guide % Can't set mrouter on a port which belongs to an aggregation port. Explanation A port belonging to a link aggregation group cannot be specified as an mrouter port. Solution Review the specified port number and reissue the command. When registering an aggregation group specify “agg-port”.
Page 194: Ip Snooping Vlan Fast-Leave
XG2000 series User's Guide 5.15.7 ip snooping vlan fast-leave Function Set the Fast Leave mode on the IP multicast group port where the IGMP Leave message is received. In the Fast Leave mode, the exit is not checked when the IGMP Leave message is received.
Page 195: Ip Snooping Vlan Last-Member-Query-Interval
XG2000 series User's Guide 5.15.8 ip snooping vlan last-member-query-interval Function Sets the monitoring time (in seconds) for checking on the exit of the last member of a IP multicast group. If an IGMP Report message is not issued within the monitoring time after reception of an IGMP Leave message, the IP multicast group is deleted.
Page 196: Ip Snooping Vlan Send-Query-Count
XG2000 series User's Guide 5.15.9 ip snooping vlan send-query-count Function Sets a query message transmission frequency. Use the no form to return to the default setup. Prompt xg(config)# Command syntax ip snooping vlan <1-4094> send-query-count <1-3> no ip snooping vlan <1-4094> send-query-count Parameter vlan <1-4094>...
Page 197: Ip Snooping Vlan Querier
XG2000 series User's Guide 5.15.10 ip snooping vlan querier Function The IGMP Querier function sends an IGMP General Query message to each terminal node instead of the multicast router if no multicast router exists on the network segment. This command enables the IGMP querier. The query message transmission interval (called “Query interval”) is calculated based on the query message transmission frequency and the group valid time interval (called “Group member interval”) as...
Page 198: Ip Snoop
XG2000 series User's Guide 5.15.11 ip snoop Function Enables IGMP snooping for specified VLANs. This command is enabled after enabling global IGMP snooping using the “ip snooping protocol” command. Use the no form to return to the default setup. Prompt...
Page 199: Ip Snooping Max-Group
XG2000 series User's Guide 5.15.12 ip snooping max-group Function Defines the number of multicast groups that can be registered for IGMP snooping on specified VLANs. Use the no form to return to the default setup. Prompt xg(config-vlan)# Command syntax max-group <10-128>...
Page 200: Ip Snooping Mrouter
XG2000 series User's Guide 5.15.13 ip snooping mrouter Function Automatically learns the IGMP query message receiving port as a multicast router port. This command can statically set multicast router ports. Also, it can change the automatic learning mode of multicast router ports.
Page 201: Ip Snooping Group-Member-Interval
XG2000 series User's Guide % Can't set mrouter on a port which belongs to an aggregation port. Explanation A port belonging to a link aggregation group cannot be specified as an mrouter port. Solution Review the specified port number and reissue the command. When registering an aggregation group specify “agg-port”.
Page 202: Ip Snooping Fast-Leave
XG2000 series User's Guide 5.15.15 ip snooping fast-leave Function Set the Fast Leave mode on the IP multicast group port where the IGMP Leave message is received. In the Fast Leave mode, the exit is not checked when the IGMP Leave message is received.
Page 203: Ip Snooping Last-Member-Interval
XG2000 series User's Guide 5.15.16 ip snooping last-member-interval Function Sets the monitoring time (in seconds) for checking on the exit of the last member of a IP multicast group. If an IGMP Report message is not issued within the monitoring time after reception of an IGMP Leave message, the IP multicast group is deleted.
Page 204: Ip Snooping Send-Query-Count
XG2000 series User's Guide 5.15.17 ip snooping send-query-count Function Sets a query message transmission frequency. Use the no form to return to the default setup. Prompt xg(config-vlan)# Command syntax ip snooping send-query-count <1-3> no ip snooping send-query-count Parameter send-query-count <1-3>...
Page 205: Ip Snooping Querier
XG2000 series User's Guide 5.15.18 ip snooping querier Function The IGMP Querier function sends an IGMP General Query message to each terminal node instead of the multicast router if no multicast router exists on the network segment. This command enables the IGMP querier. The query message transmission interval (called “Query interval”) is calculated based on the query message transmission frequency and the group valid time interval (called “Group member interval”) as...
Page 206: Statistics Commands
XG2000 series User's Guide 5.16 Statistics Commands The device provides a wide variety of statistical displays. Statistics can be displayed using the “monitor” command, which periodically updates the display information, or by using the “show statistics” command which displays a snapshot.
Page 207: Monitor Traffic-Bytes
XG2000 series User's Guide 5.16.1 monitor traffic-bytes Function Displays the transmission frame length (in bytes) at each port. Prompt xg> or xg# Command syntax monitor traffic-bytes { current | total } [interval <3-60>] Parameter { current | total } Specifies the statistics to be displayed.
Page 208 XG2000 series User's Guide Port-Description Displays port descriptions. If the port is not described, it will not display anything. Up to 33 characters can be displayed. Output form (if "total" is specified) xg# monitor traffic-bytes total Traffic Statistics(Total Frame Bytes)
Page 209: Monitor Traffic-Counts
XG2000 series User's Guide 5.16.2 monitor traffic-counts Function Displays the transmission frame count at each port. Prompt xg> or xg# Command syntax monitor traffic-counts { current | total } [interval <3-60>] Parameter { current | total } Specifies the statistics to be displayed.
Page 210 XG2000 series User's Guide Rx-Bcast Counts Displays the number of accumulated receive broadcast frames after execution of this command, using a 10-digit, right-justified value. Rx-Mcast Counts Displays the number of accumulated receive multicast frames after execution of this command, using a 10-digit, right-justified value.
Page 211: Monitor Framesize-Traffic-Counts
XG2000 series User's Guide 5.16.3 monitor framesize-traffic-counts Function Displays a frame count and size range for frames which have been sent or received at each port. Prompt xg> or xg# Command syntax monitor framesize-traffic-counts { current | total } [interval <3-60>]...
Page 212 XG2000 series User's Guide FrameSize 256-511 Displays the number of accumulated 256- to 511-byte frames sent or received after the command execution. FrameSize 512-1023 Displays the number of accumulated 512- to 1023-byte frames sent or received after the command execution.
Page 213: Monitor Qos-Priority-Traffic-Bytes
XG2000 series User's Guide 5.16.4 monitor qos-priority-traffic-bytes Function Displays the number of bytes received at each port for each QoS priority. Prompt xg> or xg# Command syntax monitor qos-priority-traffic-bytes { current | total } [interval <3-60>] Parameter { current | total } Specifies the statistics to be displayed.
Page 214 XG2000 series User's Guide Output form (if "total" is specified) xg# monitor qos-priority-traffic-bytes total Qos Priority Traffic Statistics(Total Frame Bytes) 2007/01/22-12:12:15 ===================================================================================> Port Priority-0 Priority-1 Priority-2 Priority-3 Priority-4 Priority-5 Priority-6 Bytes Bytes Bytes Bytes Bytes Bytes Bytes ---- ----------- ----------- ----------- ----------- ----------- ----------- -----------...
Page 215: Monitor Qos-Priority-Traffic-Counts
XG2000 series User's Guide 5.16.5 monitor qos-priority-traffic-counts Function Displays the number of frames received at each port for each QoS priority. Prompt xg> or xg# Command syntax monitor qos-priority-traffic-counts { current | total } [interval <3-60>] Parameter { current | total } Specifies the statistics to be displayed.
Page 216 XG2000 series User's Guide Output form (if "total" is specified) xg# monitor qos-priority-traffic-counts total Qos Priority Traffic Statistics(Total Frame Counts) 2007/01/22-12:12:15 ===================================================================================> Port Priority-0 Priority-1 Priority-2 Priority-3 Priority-4 Priority-5 Priority-6 Counts Counts Counts Counts Counts Counts Counts ---- ----------- ----------- ----------- ----------- ----------- ----------- -----------...
Page 217: Monitor Vlan-Traffic-Bytes
XG2000 series User's Guide 5.16.6 monitor vlan-traffic-bytes Function Displays the received byte count of each VLAN. Prompt xg> or xg# Command syntax monitor vlan-traffic-bytes { current | total } [interval <3-60>] Parameter { current | total } Specifies the statistics to be displayed.
Page 218: Monitor Vlan-Traffic-Counts
XG2000 series User's Guide 5.16.7 monitor vlan-traffic-counts Function Displays the received frame count of each VLAN. Prompt xg> or xg# Command syntax monitor vlan-traffic-counts { current | total } [interval <3-60>] Parameter { current | total } Specifies the statistics to be displayed.
Page 219: Monitor Dataflow
XG2000 series User's Guide 5.16.8 monitor dataflow Function Displays statistics including both pause frame transmission to and from each port and the results of transmission processing. Prompt xg> or xg# Command syntax monitor dataflow { current | total } [interval <3-60>]...
Page 220 XG2000 series User's Guide Flood Counts Displays the accumulated number of flooded frames among the unicast frames received at each port after the startup of this command. Rx-Pause Counts Displays the accumulated number of pause frames received at each port after the startup of this command.
Page 221: Monitor Error
XG2000 series User's Guide 5.16.9 monitor error Function Displays error traffic statistics for each port. Prompt xg> or xg# Command syntax monitor error { current | total } [interval <3-60>] Parameter { current | total } Specifies the statistics to be displayed.
Page 222 XG2000 series User's Guide Rx Align Displays the accumulated number of 64- to 1518-byte alignment error frames whose bit size is not a multiple of 8 received after startup of this command. Total Lost Displays the accumulated number of frames received but discarded at each port after startup of this command.
Page 223: Show Statistics Traffic-Bytes
XG2000 series User's Guide 5.16.10 show statistics traffic-bytes Function Displays the accumulated number of bytes sent or received to and from each port after the system startup. Prompt xg> or xg# Command syntax show statistics traffic-bytes Command type Operation management command...
Page 224: Show Statistics Traffic-Counts
XG2000 series User's Guide 5.16.11 show statistics traffic-counts Function Displays the accumulated number of frames sent or received to and from each port after the system startup. Prompt xg> or xg# Command syntax show statistics traffic-counts Command type Operation management command...
Page 225: Show Statistics Framesize-Traffic-Counts
XG2000 series User's Guide 5.16.12 show statistics framesize-traffic-counts Function Displays traffic statistics for each port in different frame size groups. Prompt xg> or xg# Command syntax show statistics framesize-traffic-counts Command type Operation management command Output form xg# show statistics framesize-traffic-counts...
Page 226: Show Statistics Qos-Priority-Traffic-Bytes
XG2000 series User's Guide 5.16.13 show statistics qos-priority-traffic-bytes Function Displays the traffic (the number of frames) for each port with different QoS priorities after system startup. Prompt xg> or xg# Command syntax show statistics qos-priority-traffic-bytes Command type Operation management command...
Page 227: Show Statistics Qos-Priority-Traffic-Counts
XG2000 series User's Guide 5.16.14 show statistics qos-priority-traffic-counts Function Displays the traffic (the number of frames) for each port with different QoS priorities after system. Prompt xg> or xg# Command syntax show statistics qos-priority-traffic-counts Command type Operation management command Output form...
Page 228: Show Statistics Vlan-Traffic-Bytes
XG2000 series User's Guide 5.16.15 show statistics vlan-traffic-bytes Function Displays the traffic (the number of bytes) for each VLAN after system startup. Prompt xg> or xg# Command syntax show statistics vlan-traffic-bytes Command type Operation management command Output form xg# show statistics vlan-traffic-bytes...
Page 229: Show Statistics Vlan-Traffic-Counts
XG2000 series User's Guide 5.16.16 show statistics vlan-traffic-counts Function Displays the traffic (the number of frames) for each VLAN after system startup. Prompt xg> or xg# Command syntax show statistics vlan-traffic-counts Command type Operation management command Output form xg# show statistics vlan-traffic-counts...
Page 230: Show Statistics Dataflow
XG2000 series User's Guide 5.16.17 show statistics dataflow Function Displays statistics including the transmission and reception of pause frames at each port and the data transmission type. Prompt xg> or xg# Command syntax show statistics dataflow Command type Operation management command...
Page 231: Show Statistics Error
XG2000 series User's Guide 5.16.18 show statistics error Function Displays statistics for errors occurring at each port after system startup. Prompt xg> or xg# Command syntax show statistics error Command type Operation management command Output form xg# show statistics error...
Page 232: Clear Statistics
XG2000 series User's Guide 5.16.19 clear statistics Function Clears all statistics stored since system startup. The following statistics are cleared. Traffic statistics: traffic-bytes, traffic-counts and framesize-traffic-counts QoS traffic statistics: qos-priority-traffic-bytes and qos-priority-traffic-counts VLAN traffic statistics: vlan-traffic-bytes and vlan-traffic-counts Data flow statistics: dataflow...
Page 233: Snmp Setup Commands
XG2000 series User's Guide 5.17 SNMP Setup Commands This section explains the SNMP configuration settings. 5.17.1 show snmp-server Function Displays the current SNMP settings. Prompt xg> or xg# Command syntax show snmp-server Command type Operation management command Output form xg# show snmp-server...
Page 234: Snmp-Server Location
XG2000 series User's Guide 5.17.2 snmp-server location Function Sets the installation location for the device. Use the no form to return to the default setup. Prompt xg(config)# Command syntax snmp-server location SYSTEM-LOCATION no snmp-server location Parameter SYSTEM-LOCATION Specifies the installation location of the device. The location name can be up to 255 alphanumeric characters.
Page 235: Snmp-Server Contact
XG2000 series User's Guide 5.17.3 snmp-server contact Function Sets the installation contact name for the device. Use the no form to return to the default setup. Prompt xg(config)# Command syntax snmp-server contact SYSTEM-CONTACT no snmp-server contact Parameter SYSTEM-CONTACT Specifies the system contact name for the device. The contact name can be up to 255 alphanumeric characters.
Page 236: Snmp-Server Access
XG2000 series User's Guide 5.17.4 snmp-server access Function Sets an SNMP agent. The SNMP manager has read-only access privileges. Up to four access-enabled SNMP managers can be registered. Use the no form to delete the existing SNMP managers. Prompt xg(config)#...
Page 237: Snmp-Server Trap
XG2000 series User's Guide 5.17.5 snmp-server trap Function Sets the destination for SNMP trap notifications. Up to four (4) destinations can be registered. Use the no form to delete the existing destination names. Prompt xg(config)# Command syntax snmp-server trap host HOSTNAME community COMMUNITY-NAME [ protocol {v1|v2c} ]...
Page 238: Rmon Setup Commands
XG2000 series User's Guide 5.18 RMON Setup Commands This section explains the RMON configuration settings. 5.18.1 show rmon Function Displays the current RMON settings. Prompt xg> or xg# Command syntax show rmon Command type Operation management command Output form xg# show rmon...
Page 239 XG2000 series User's Guide Rising Threshold Indicates the threshold upper limit (or the rising threshold). Rising Event Indicates a number for the event notification if the value obtained exceeded the threshold limit. Event does not occur if the value is 0.
Page 240: Rmon Collection History
XG2000 series User's Guide 5.18.2 rmon collection history Function Sets an RMON history. Up to 40 entries can be set. Use the no form to delete the information set. Prompt xg(config)# Command syntax rmon collection history INDEX { port <1-20> | agg-port <1-10> }...
Page 241: Rmon Alarm
XG2000 series User's Guide 5.18.3 rmon alarm Function Sets RMON alarms. Up to 30 entries can be set. Use the no form to delete entries previously set. Prompt xg(config)# Command syntax rmon alarm INDEX VARIABLE interval VALUE {absolute | delta}...
Page 242 XG2000 series User's Guide % It failed in the snmpset command. Explanation It fails to set RMON because the command was executed while the SNMP manager was accessing. Solution While the SNMP is not accessing, execute the no command and set RMON again.
Page 243: Rmon Event
XG2000 series User's Guide 5.18.4 rmon event Function Sets an RMON event. Up to 60 entries can be set. Use the no form to delete the information set. Prompt xg(config)# Command syntax rmon event INDEX [ log ] [ trap COMMUNITY ] [ description DESCRIPTION-STRING ]...
Page 244 XG2000 series User's Guide % It failed in the snmpset command. Explanation It fails to set RMON because the command was executed while the SNMP manager was accessing. Solution While the SNMP is not accessing, execute the no command and set RMON again.
Page 245: System Operation Display Commands
XG2000 series User's Guide 5.19 System Operation Display Commands This section explains commands that display the system’s operational status. 5.19.1 show system status Function Displays the hardware operational status. For explanations and actions to be taken for each item, see the "Verifying Hardware...
Page 246 XG2000 series User's Guide − 1.5V Displays the 1.5V voltage status on the CPU board. − 3.3V Displays the 3.3V voltage status on the CPU board. − Displays the 12V voltage status on the CPU board. − 3.3V Displays the 3.3V voltage status on the switch ASIC board.
Page 247: Show System Information
XG2000 series User's Guide 5.19.2 show system information Function Displays the operational status of the device. Prompt xg> or xg# Command syntax show system information Command type Operation management command Output form xg# show system information System Information 2007/01/22-21:06:11 =======================================...
Page 248 XG2000 series User's Guide Timezone Displays the current time zone settings. If the time zone settings were changed, the new settings are displayed in the “Next Boot” area. Once the system is restarted the new settings appear as the Timezone setting.
Page 249: Show Optical-Module Sensor
XG2000 series User's Guide 5.19.3 show optical-module sensor Function Displays the sensor values which is installed on the optical module. Prompt xg> or xg# Command syntax show optical-module sensor [ dbm ] Parameter Display the strength of the laser in “dBm”.
Page 250: System Maintenance Commands
XG2000 series User's Guide 5.20 System Maintenance Commands 5.20.1 clear log Function Initializes the system log. Prompt Command syntax clear log [ { info | warning | error | critical } ] Parameter { info | warning | error | critical } Specifies the type of system log to be initialized.
Page 251: Show Log
Displays the day when the event occurred. Hours Min Sec Displays the time (hours, minutes and seconds) when the event occurred. Host name of the device Displays the host name of the XG2000 series. Function name Displays the function name. Severity Indicates the severity of the message.
Page 252: Log Send
XG2000 series User's Guide − Message number Displays a unique number for message identification. Read this message number to locate the message and take necessary actions. Message text Displays the message text. Example Display 10 entries of the latest INFO log: xg# show log info latest 10 5.20.3 log send...
Page 253: Save Maintenance
XG2000 series User's Guide 5.20.4 save maintenance Function Stores the current internal system status in non-volatile memory. Prompt Command syntax save maintenance Command type Operation management command Message % Cannot execute simultaneously. Explanation “save maintenance” is executed while it is being executed in other console.
Page 254: Tftp Put-Maintenance
XG2000 series User's Guide 5.20.6 tftp put-maintenance Function Transfers the system maintenance information to a TFTP server. The file size of the maintenance information is displayed on the screen. Prompt Command syntax tftp put-maintenance HOST [ REMOTE-FILE ] Parameter HOST Specifies the host name or the IP address of the TFTP server.
Page 255 XG2000 series User's Guide Example Save the current system status data as a maintenance information file in non-volatile memory then check the logged status of the maintenance information using the “show maintenance” command. Transfer the maintenance information to the “host1” TFTP server by naming it as the “mainte_collected date and time” file.
Page 256: Scp Put-Maintenance
XG2000 series User's Guide 5.20.7 scp put-maintenance Function Transfers the system maintenance information to a SSH server. The file size of the maintenance information is displayed on the screen. Prompt Command syntax scp put-maintenance USERNAME HOST [ REMOTE-FILE ] Parameter USERNAME Specifies the username of the SSH server.
Page 257 XG2000 series User's Guide ssh: connect to host %1$ port 22: Network is unreachable Explanation It failed to access to specified SSH server. [[Inserted string]]%1$: Specified IP address or host name. Solution Specify the correct IP address or host name.
Page 258: Clear Maintenance
XG2000 series User's Guide 5.20.8 clear maintenance Function Clears the maintenance information from non-volatile memory on the device. Prompt Command syntax clear maintenance Command type Operation management command Note Issue the “clear maintenance” command only after checking for a successful file transfer to the remote server using the “tftp put-maintenance”...
Page 259: Update-System
XG2000 series User's Guide 5.20.9 update-system Function Updates the firmware on the device. The device stores two firmware images. This command updates the standby firmware. The updated firmware is made valid after the next system startup. Prompt Command syntax update-system local FILE-NAME...
Page 260 XG2000 series User's Guide % Writing %1$ into FlashROM failed. Explanation An error occurred while writing to flash ROM. [[Inserted string]]%1$: Firmware configuration module Solution Retry firmware updating. If the error recurs, contact the sales representative. % Checksum error: %1$ in FlashROM Explanation An error occurred while writing to flash ROM.
Page 261 XG2000 series User's Guide scp: %1$: No such file or directory Explanation Specified file does not exist. [[Inserted string]]%1$: Specified file name. Solution Specify the correct file name. scp: %1$: Permission denied Explanation There was no access permission to the SSH server.
Page 262 XG2000 series User's Guide Example Download the firmware image file into the system volatile memory using the “tftp get” command. Check the size of the downloaded firmware image file using the “ls” command. Then, update the firmware using the “update-system” command.
Page 263: Boot-System
XG2000 series User's Guide 5.20.10 boot-system Function Switches the firmware image to be used for the next system startup. Use this command only if a problem occurred using new firmware. Prompt Command syntax boot-system { 1 | 2 } Parameter { 1 | 2 } Specifies the number of the firmware partition to be used during the next system startup.
Page 264: Chapter 6 Managing The Device
XG2000 series User's Guide Chapter 6 Managing the Device This chapter describes the management of the device. 264/315 All Rights Reserved, Copyright (C) PFU LIMITED 2009...
Page 265: Verifying The Device Operations
XG2000 series User's Guide 6.1 Verifying the Device Operations This chapter describes the management of the device. Hardware status System status Log messages 6.1.1 Verifying Hardware Status Verify the status of hardware by entering the "show system status" command in the operator EXEC mode or in the administrator EXEC mode.
Page 266 XG2000 series User's Guide The following table provides descriptions of items displayed when the "show system status" command is entered and an explanation of each error message. Item Item displayed Message explanation/Solution Temperature Displays the temperature inside the chassis. Internal (internal temperature sensor) good The temperature is within normal operating range.
Page 267 XG2000 series User's Guide Displays the status of the fans. Rear Fan-0 good (normal-speed) The fan is working at a normal speed. good (high-speed) The fan is working at a high speed. Removed The fan was removed. Check that the fan is installed.
Page 268: Verifying System Status
XG2000 series User's Guide 6.1.2 Verifying System Status Verify the system status by entering the "show system information" command in the operator EXEC mode or in the administrator EXEC mode. The following example shows the information that is displayed when the "show system...
Page 269: Format Of Log Message
XG2000 series User's Guide 6.1.3.1 Format of Log Message An example of the format of a log message displayed by the "show log" command is shown below. xg# show log info latest 1 May 25 22:08:33 xghost xgsh: XG INFO[P4001]: cmd-exec[3388]: show log info latest 1...
Page 270: Verifying The Device Status Change
XG2000 series User's Guide 6.1.3.3 Verifying the Device Status Change To verify changes in the device status, review INFO log messages. Enter the "show log" command in the operator EXEC mode or in the administrator EXEC mode. For the meaning of messages, refer to "List of System Logs".
Page 271: Uploading/Downloading A Configuration File
XG2000 series User's Guide 6.2 Uploading/Downloading a Configuration File The configuration file, generated in the device, can be uploaded to a remote server. Also, when an uploaded configuration file is downloaded from a remote server, the configuration of the device can be restored.
Page 272: Updating Firmware
XG2000 series User's Guide 6.3 Updating Firmware The device can hold two versions of firmware. If a firmware update is performed, the inactive firmware will be updated. The device automatically uses the new firmware (updated version) during reboot after the firmware update. If the switch fails to start the new firmware, it automatically uses the old version (the one that was not updated).
Page 273: Selecting Firmware
XG2000 series User's Guide 6.3.2 Selecting Firmware This section describes the procedures for selecting the firmware to use. After logging into the device, use the "enable" command to switch to administrator EXEC mode. xg> enable Using the "show system information" command, check the status of the firmware.
Page 274: Extracting Of Maintenance Information
XG2000 series User's Guide 6.4 Extracting of Maintenance Information If a fault occurred, maintenance information may be requested by the device sales representative to investigate the cause of the fault. This section provides procedures for extracting maintenance information. Depending on the situations shown below, extract maintenance information using the described procedures.
Page 275: Procedure For Extracting Maintenance Information When An Endless System Loop Occurred
XG2000 series User's Guide 6.4.2 Procedure for Extracting Maintenance Information when an endless System Loop Occurred This section describes the procedures for extracting maintenance information when an endless system loop occurs. A system loop occurred. If a CLI command entry is not accepted for an extended period of time, a system loop may exist.
Page 276: Chapter 7 Troubleshooting
XG2000 series User's Guide Chapter 7 Troubleshooting This chapter describes how to solve problems that might be encountered when using the device. 276/315 All Rights Reserved, Copyright (C) PFU LIMITED 2009...
Page 277: Restoring Factory Defaults
XG2000 series User's Guide 7.1 Restoring Factory Defaults 7.1.1 Resetting startup-config to Factory Defaults To reset all settings in the device's startup-config file to the factory defaults: Using the "reset factory-default" command, reset the contents of the startup-config file to the factory defaults.
Page 278: Restoring Factory Defaults
XG2000 series User's Guide 7.1.3 Restoring Factory Defaults If the system still fails to start up with another firmware image selected, perform the following procedure to restore the device to factory defaults. (Step 1) Connect the device to a serial terminal.
Page 280: Appendix A Event Logs
XG2000 series User's Guide Appendix A Event Logs This appendix describes event logs that are extracted from the device, including message IDs, severities, message content details, and actions to take. The severities of the event logs are classified into 4 levels -- CRITICAL, ERROR, WARNING, and INFO.
Page 281: List Of Event Logs
XG2000 series User's Guide List of Event Logs This section provides an explanation of message contents and actions to take for the associated message ID and severity in ascending numerical order. There is no solution provided for messages that do not required action.
Page 282 XG2000 series User's Guide Message ID Message/Explanation/Solution Severity S0109 %1$ Speed is below the Low Limit. (%2$ %3$) WARNING Explanation The speed of a fan is below limit. [[Inserted string]]%1$: Displays the location of the detected fan speed error. Rear Fan-0: Rear fan 0...
Page 283: Kernel (Basic Control: 1000-1999)
XG2000 series User's Guide Message ID Message/Explanation/Solution Severity S0124 Internal Temperature is high. (%1$ %2$) Info Explanation The temperature is high. The system will be shut down if the temperature rises. [[Inserted string]]%1$, %2$: Temperature value Solution Perform the following checks on the device: Check that the air vent is not blocked.
Page 284: Swc (Layer 2 Basic Control: 2000-2999)
XG2000 series User's Guide Message ID Message/Explanation/Solution Severity S1960 Too many DRAM SBE detected.(%1$) ERROR Explanation The software detected too many DRAM single bit errors. No more events will be logged. [[Inserted string]]%1$: Details about error Solution The device supports single bit ECC, so the error is corrected. But a failure may occur if the error happens again after a system reset.
Page 285 XG2000 series User's Guide Message ID Message/Explanation/Solution Severity S2112 ME Halt detected. %1$ ERROR Explanation An uncorrectable error was detected in the switch chip. [[Inserted string]]%1$: Supplementary code for the error Solution Note the message contents and contact the sales representative.
Page 286 XG2000 series User's Guide Message ID Message/Explanation/Solution Severity S2208 Stream Memory Tag MBE detected. %1$ WARNING Explanation An uncorrectable error was detected in the switch chip. [[Inserted string]]%1$: Supplementary code for the error Solution Note the message contents and contact the sales representative.
Page 287 XG2000 series User's Guide Message ID Message/Explanation/Solution Severity S2217 Too Many Input Queue Tag Memory SBE Errors. LOG Disabled. WARNING Explanation A correctable error was repeatedly detected in the switch chip. Logging for this event is disabled. Solution Note the message contents and contact the sales representative.
Page 288: Npm (Network Protocol Control: 3000-3299)
XG2000 series User's Guide Message ID Message/Explanation/Solution Severity S2226 Too Many CM Buffer SBE Errors. LOG Disabled. WARNING Explanation A correctable error was repeatedly detected in the switch chip. Logging for this event is disabled. Solution Note the message contents and contact the sales representative.
Page 289 XG2000 series User's Guide Message ID Message/Explanation/Solution Severity P3011 %1$ link status details change %2$. INFO Explanation The link status of the port changed. [[Inserted string]]%1$: Port information [[Inserted string]]%2$: New status of the port P3012 %1$ state is changed to %2$.
Page 290 XG2000 series User's Guide Message ID Message/Explanation/Solution Severity P3206 Destination IP-address doesn't match with IGMP group address in IGMP report message. WARNING Explanation Received a frame containing at destination IP address that does not match the IGMP group address in an IGMP Report message.
Page 291 XG2000 series User's Guide Message ID Message/Explanation/Solution Severity P3216 IGMP snooping has deleted multicast group address. Group(%1$) vlan-%2$ port %3$ INFO Explanation IGMP snooping deleted a multicast group MAC address. [[Inserted string]]%1$: Deleted IP group address [[Inserted string]]%2$: Deleted VLAN ID...
Page 292: Clim (Basic Cli Control: 3300-3999)
XG2000 series User's Guide A.2.5 clim (Basic CLI Control: 3300-3999) Message ID Message/Explanation/Solution Severity P3300 cmd-exec[startup]: %1$ INFO Explanation The command in the startup-config was executed. [[Inserted string]]%1$: Command string executed in the startup-config. P3301 cmd-result[startup]: success INFO Explanation The command in the startup-config was successfully completed.
Page 293: Xgsh (Cli Command History: 4000-4499)
XG2000 series User's Guide A.2.6 xgsh (CLI Command History: 4000-4499) Message ID Message/Explanation/Solution Severity P4001 %1$ cmd-exec[%2$]: %3$ INFO Explanation The command was executed. [[Inserted string]]%1$: Username [[Inserted string]]%2$: Terminal ID [[Inserted string]]%3$: Command string to be executed P4002 %1$ cmd-result[%2$]: success...
Page 294: Lacp (Lacp Control: 5000-5499)
XG2000 series User's Guide Message ID Message/Explanation/Solution Severity P4508 Invalid "Max age" relationship 2*(%1$ + 1) <= %2$. WARNING Explanation The setting of STP Max Age is invalid. [[Inserted string]]%1$: The current Hello Time value [[Inserted string]]%2$: Attempted Max Age value change Solution Check that the setting of Max Age satisfies the following condition.
Page 295: Update (Firmware Update: 7500-7999)
XG2000 series User's Guide Message ID Message/Explanation/Solution Severity S7492 A system-dump has been saved. Cause: machine check occurred (memory or bus data error). CRITICAL Explanation A machine check error occurred and a system dump saved. Solution Obtain maintenance information using the "tftp...
Page 296 XG2000 series User's Guide Message ID Message/Explanation/Solution Severity S7531 init-firmup: Internal error occurred (SRAM access error). CRITICAL Explanation An error occurred while processing the firmware update information. Solution Note the message contents and contact the sales representative. S7532 init-firmup: Internal error occurred (FlashROM access error).
Page 297 XG2000 series User's Guide Message ID Message/Explanation/Solution Severity S7625 firm-update: failed (verification error: kernel). ERROR Explanation An error occurred while updating firmware. Solution Reattempt the update process. If the message is repeatedly displayed, note the message contents and contact the sales representative.
Page 298: Snmp (Snmp Control: 8500-8599)
XG2000 series User's Guide A.2.11 snmp (SNMP Control: 8500-8599) Message ID Message/Explanation/Solution Severity S8500 SNMP authentication failure. INFO Explanation The device denied an SNMP request from a SNMP manager. Solution Review the SNMP permission from the SNMP manager using the "snmp access" command.
Page 299: Ntp (Ntp Control: 8600-8699)
XG2000 series User's Guide A.2.12 ntp (NTP Control: 8600-8699) Message ID Message/Explanation/Solution Severity P8601 No server suitable for synchronization found. WARNING Explanation No NTP server is found. Solution Check the NTP server host name defined by the "ntp-server" command as well as the NTP server operating status.
Page 300: Message Format For Forwarding Syslog
XG2000 series User's Guide Message Format for Forwarding syslog The logs output from the device can be forwarded to a syslog server. The device forwards logs in a message format that conforms to the RFC3164 The BSD Syslog Protocol. The format the device uses to forward a syslog message to the syslog server is shown below.
Page 301: Appendix Bsnmp Traps
XG2000 series User's Guide Appendix B SNMP Traps This appendix lists the SNMP traps supported by the device. Standard SNMP Traps Trap name Trap OID coldStart 3418 1.3.6.1.6.3.1.1.5.1 linkDown 2863 1.3.6.1.6.3.1.1.5.3 linkUp 2863 1.3.6.1.6.3.1.1.5.4 authenticationFailure 3418 1.3.6.1.6.3.1.1.5.5 risingAlarm 2819 1.3.6.1.2.1.16.0.1...
Page 302: Appendix C List Of Mibs
XG2000 series User's Guide Appendix C List of MIBs This appendix lists the MIBs supported by the device. For a definition of each object, refer to RFC. MIB-II system group (RFC3418) iso(1).org(3).dod(6).internet(1).mgmt(2).mib-2(1).system(1) Item Object identifier SYNTAX number sysDescr DisplayString {system 1}...
Page 303 XG2000 series User's Guide Item Object identifier SYNTAX number ifSpecific OBJECT IDENTIFIER {ifEntry 22} Ether-like MIB (RFC2665) iso(1).org(3).dod(6).internet(1).mgmt(2).mib-2(1).transmission(10).dot3(7) Item Object identifier SYNTAX number dot3StatsTable NOT-ACCESSIBLE {dot3 2} dot3StatsEntry NOT-ACCESSIBLE {dot3StatsTable 1} dot3StatsIndex InterfaceIndex {dot3StatsEntry 1} dot3StatsAlignmentErrors Counter32 {dot3StatsEntry 2} dot3StatsFCSErrors...
Page 304 XG2000 series User's Guide Item Object identifier SYNTAX number snmpInBadCommunityUses Counter32 {snmp 5} snmpInASNParseErrs Counter32 {snmp 6} snmpInTooBigs Counter32 {snmp 8} snmpInNoSuchNames Counter32 {snmp 9} snmpInBadValues Counter32 {snmp 10} snmpInReadOnlys Counter32 {snmp 11} snmpInGenErrs Counter32 {snmp 12} snmpInTotalReqVars Counter32 {snmp 13}...
Page 305 XG2000 series User's Guide Item Object identifier SYNTAX number etherStatsCRCAlignErrors Counter32 {etherStatsEntry 8} etherStatsUndersizePkts Counter32 {etherStatsEntry 9} etherStatsOversizePkts Counter32 {etherStatsEntry 10} etherStatsFragments Counter32 {etherStatsEntry 11} etherStatsJabbers Counter32 {etherStatsEntry 12} etherStatsCollisions Counter32 {etherStatsEntry 13} etherStatsPkts64Octets Counter32 {etherStatsEntry 14} etherStatsPkts65to127Octets Counter32 {etherStatsEntry 15}...
Page 306 XG2000 series User's Guide Item Object identifier SYNTAX number etherHistoryOversizePts Counter32 {etherHistoryEntry 11} etherHistoryFragments Counter32 {etherHistoryEntry 12} etherHistoryJabbers Counter32 {etherHistoryEntry 13} etherHistoryCollisions Counter32 {etherHistoryEntry 14} etherHistoryUtilization Integer32 {etherHistoryEntry 15} RMON MIB (alarm group) (RFC2819) iso(1).org(3).dod(6).internet(1).mgmt(2).mib-2(1).rmon(16).alarm(3) Item Object identifier SYNTAX number...
Page 307 XG2000 series User's Guide Item Object identifier SYNTAX number logDescription DisplaySting {logEntry 4} Bridge MIB (RFC1493) iso(1).org(3).dod(6).internet(1).mgmt(2).mib-2(1).dot1dBridge (17) Item Object identifier SYNTAX number dot1dBase NOT-ACCESSIBLE {dot1dBridge 1} dot1dBaseBridgeAddress MacAddress {dot1dBase 1} dot1dBaseNumPorts INTEGER {dot1dBase 2} dot1dBaseType INTEGER {dot1dBase 3} dot1dBasePortTable...
Page 308 XG2000 series User's Guide Item Object identifier SYNTAX number dot1dStpPortDesignatedCost INTEGER {dot1dStpPortEntry 7} dot1dStpPortDesignatedBridge BridgeId {dot1dStpPortEntry 8} dot1dStpPortDesignatedPort OCTET STRING {dot1dStpPortEntry 9} dot1dStpPortForwardTransitions Counter {dot1dStpPortEntry 10} dot1dTp NOT-ACCESSIBLE {dot1dBridge 4} dot1dTpLearnedEntryDiscards Counter {dot1dTp 1} dot1dTpAgingTime INTEGER {dot1dTp 2} dot1dTpPortTable NOT-ACCESSIBLE...
Page 309 XG2000 series User's Guide Item Object identifier SYNTAX number dot1dPortNumTrafficClasses INTEGER {dot1dPortPriorityEntry 2} dot1dTrafficClassTable NOT-ACCESSIBLE {dot1dPriority 3} dot1dTrafficClassEntry NOT-ACCESSIBLE {dot1dTrafficClassTable 1} dot1dTrafficClassPriority INTEGER {dot1dTrafficClassEntry 1} dot1dTrafficClass INTEGER {dot1dTrafficClassEntry 2} Q-Bridge MIB (RFC2674) iso(1).org(3).dod(6).internet(1).mgmt(2).mib-2(1).dot1dBridge(17).QBridgeMIB(7) Item Object identifier SYNTAX number qBridgeMIBObjects NOT-ACCESSIBLE...
Page 310 XG2000 series User's Guide Item Object identifier SYNTAX number dot1qPortIngressFiltering TruthValue {dot1qPortVlanEntry 3} dot1qPortGvrpStatus EnabledStatus {dot1qPortVlanEntry 4} dot1qPortGvrpFailedRegistrations Counter32 {dot1qPortVlanEntry 5} dot1qPortGvrpLastPduOrigin MacAddress {dot1qPortVlanEntry 6} IF MIB (RFC2863) iso(1).org(3).dod(6).internet(1).mgmt(2).mib-2(1). ifMIB (31) Item Object identifier SYNTAX number ifMIBObjects NOT-ACCESSIBLE {ifMIB 1}...
Page 311 XG2000 series User's Guide FUJITSU-XG2000-MIB iso(1).org(3).dod(6)internet(1).private(4).enterprises(1).fujitsu(211). Product(1).nonos(127).xg-switch(61).xg2000(107) (*.xg2000(107) becomes *.xg2000(108) in case of XG2000C, *.xg2000(109) in case of XG2000CR, and *.xg2000(110) in case of XG2000R) Item Object identifier SYNTAX Description number xg2000Monitor NOT-ACCESSIBLE Object identifier of monitor information specific to the {xg2000 1} device.
Page 312: Index
XG2000 series User's Guide Index aaa authentication login ............... 91 egress..................174 Aborting Command ..............19 enable................... 73 About Command Reference............58 enable password ................87 account..................78 Event Logs ................. 280 exit....................75 Extraction of Maintenance Information........274 banner ..................88 baud-rate ..................
Page 313 XG2000 series User's Guide LFS....................31 line....................67 Link Aggregation................32 RADIUS Attridutes................ 55 Link Aggregation Configuration Commands....... 130 RADIUS/TACACS+ ..............90 Link Fault Signaling ..............31 RADIUS/TACACS+ authentication..........55 Link Pass Through ............... 31 radius-server host ................ 93 link-aggregation................134 radius-server key................
Page 314 XG2000 series User's Guide SNMP Agent................. 54 SNMP Configuration..............25 SNMP Setup Commands ............233 SNMP Traps ................301 TACACS+ Attridutes..............55 snmp-server access ..............236 tacacs-server host ................ 97 snmp-server contact..............235 tacacs-server key ................. 98 snmp-server location ..............234 Tag-Based VLAN................
Page 315 XG2000 series User's Guide P3N1-E202-01ENZ0 Date of Issue: March 2009 Issuing authority: PFU LIMITED The contents of this manual may be updated without notice. PFU assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual.

Fujitsu XG2000 Series User Manual

Preface

About this Manual

Contents

Chapter 1 Features and Functions

Chapter 2 Using the CLI

Chapter 3 Installation

Chapter 4 Switch Functions and Their Configuration

Chapter 5 Command Reference

Chapter 6 Managing the Device

Quick Links

Related Manuals for Fujitsu XG2000 Series

Summary of Contents for Fujitsu XG2000 Series