Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Fujitsu XG0440DC
Summary of Contents for Fujitsu XG0440DC
- Page 1 XG0440DC/XG0440DCR Hardware Guide Introduction TA41001-7879 XG0440DC / XG0440DCR XG0440DC / XG0440DCR Hardware Guide...
-
Page 2: Preface
XG0440DC/XG0440DCR Hardware Guide Preface The Fujitsu XG0440 is a 40 port 1 Gigabit plus 4 port 10 Gigabit Ethernet layer 2 switch that achieves unsurpassed levels of high throughput. This manual explains the procedures required to install the XG0440. Please read and fully understand the instructions before deploying the switch. -
Page 3: License Agreement
Fujitsu's aggregate liability for such damages shall not exceed the amount equal to the total price of the Product. Further, Fujitsu shall not be liable for (i) damages to the extent they are caused by conditions not attributable to Fujitsu, or... - Page 4 XG0440DC/XG0440DCR Hardware Guide c. if in Fujitsu's sole judgment it is not commercially reasonable to perform either of the above options, subject to the limitation of liability set forth in subsection (2) above, Fujitsu shall pay for any damages Customer has incurred due to nonuse of the Software.
-
Page 5: Table Of Contents
XG0440DC/XG0440DCR Hardware Guide Contents Contents Preface ................................2 LICENSE AGREEMENT ..........................3 Organization and Usage of This Manual ......................7 About This Manual ..............................7 Target Readers and Required Knowledge ......................... 7 Areas Covered ................................7 Trademark Notification in This Manual ........................8 How the Manuals for This Device Are Organized .................... - Page 6 XG0440DC/XG0440DCR Hardware Guide Contents Turn On/Turn Off the Power .........................43 2.7.1 Turn on the Power ............................ 43 2.7.2 Turn off the Power ........................... 44 Index..........................45...
-
Page 7: Organization And Usage Of This Manual
Precautions" described in this manual before using this device. Furthermore, this manual should be kept in an easy-to- access location for quick reference while using this device. Fujitsu takes the utmost care to insure that our products can be used safely without causing injury to the customer or damage to their property Target Readers and Required Knowledge This manual is intended for persons who perform network management. -
Page 8: Trademark Notification In This Manual
XG0440DC/XG0440DCR Hardware Guide Trademark Notification in This Manual All company names and product names referenced in this manual are trademarks or registered trademarks of their respective companies. How the Manuals for This Device Are Organized The manuals for this device are organized as follows. Use these manuals as necessary. -
Page 9: Safety Precautions
XG0440DC/XG0440DCR Hardware Guide Safety Precautions About Warning Descriptions This manual contains precautions that must be taken in order to use this device safely and prevent personal injury or property damage. Please fully understand the meanings and contents of the following descriptions and symbols when reading this manual. - Page 10 XG0440DC/XG0440DCR Hardware Guide Always follow the instructions for safe use of this device. Indicates that improper use can cause Warning severe damage to person, resulting in serious injury or death. Warnings Do not insert or drop any foreign objects into the If you notice abnormal conditions such as device through the vent.
- Page 11 XG0440DC/XG0440DCR Hardware Guide Indicates that improper use can cause light or moderate injury. Caution In addition, this symbol indicates a chance of damage to this device and other connected equipment. Cautions Do not touch this device for more than one Do not put objects on this device or use it as a minute while it is turned on.
-
Page 12: Notes On Maintenance
• Fujitsu and its partners accept no responsibility for any errors or data loss arising from use of the product. Before using the product, it should be understood that the device is not guaranteed against failure for any more than the original purchase price. -
Page 13: Electromagnetic Compatibility (Usa)
Do not use the XG0440 for High Safety Required applications without otherwise ensuring the safety level required. Fujitsu and its related companies assume no liability whatsoever for damages arising from use of the XG0440 by the user in High... -
Page 14: Laser Safety
XG0440DC/XG0440DCR Hardware Guide Laser Safety The XG0440 may be installed with optical transceiver modules (SFP+ modules), which emit invisible laser light. In the USA, these optical modules are certified as Class 1 laser products that conform to the requirements of the Department of Health and Human Services (DHHS) regulation 21 CFR, Subchapter J. -
Page 15: Notes On Use
It is strongly recommended that customers store and maintain configuration information for the device after configuration is complete. The configuration information can be used by a Fujitsu or Fujitsu's certified support engineer to restore configurations if a failure occurs. Unless the configuration information is available, it may cause difficulties and delays for the support engineer in restoring the device to service, Please backup and maintain the configuration information so it is always up to date. -
Page 16: Chapter 1 Getting Started
Chapter 1 Getting Started This chapter lists the items that should be in the product package, and describes the names and functions of the various components. Items in the Package, Descriptions and Functions ........17 1.1.1 Parts List. -
Page 17: Items In The Package, Descriptions And Functions
XG0440DC/XG0440DCR Hardware Guide Chapter 1 Getting Started Items in the Package, Descriptions and Functions Before proceeding, check all the items described below. 1.1.1 Parts List Please check that all of the following parts are included in the package. XG0440 Power Cables (Qty 2) (The XG0440DC is used as an example.) -
Page 18: Switch Port Side
• USB memory is not included in the product package 1.1.2 Switch Port Side The XG0440DC is used as an example. The front and back direction of the rack mounting brackets attached to the side of the switch is reversed for the XG0440DC and XG0440DCR. Product Part Number, Serial Number Label Dump Switch... - Page 19 XG0440DC/XG0440DCR Hardware Guide Chapter 1 Getting Started • Dump Switch Press the dump switch to copy the following switch files to an installed USB memory. Information File Name Configuration Definition 1 /um0/config1 Configuration Definition 2 /um0/config2 Firmware /um0/firmware Error Log /um0/elog The switch default configuration disables the dump switch.
- Page 20 Indicates the operational state of the switch. • CHECK LED Lights orange when the switch detected an abnormal operating condition. This may indicate that the switch has failed. Consult with your Fujitsu or Fujitsu's certified support engineer immediately to correct this condition. • PSU1 LED Lights to indicate the status of the PSU1.
- Page 21 XG0440DC/XG0440DCR Hardware Guide Chapter 1 Getting Started LED Functions/Behaviors LED Name State Status LINK/ACT/ Green A 1000 Mbps link is established. SPEED Green Blinking A 1000 Mbps link is trafficking data. Orange A 100 Mbps or 10 Mbps link is established.
-
Page 22: Switch Power Inlet Side
Chapter 1 Getting Started 1.1.3 Switch Power Inlet Side The XG0440DC is used as an example. The front and back direction of the rack mounting brackets attached to the side of the switch is reversed for the XG0440DC and XG0440DCR. PSU Slots PSU Slots Fan Unit... - Page 23 CHECK Orange An abnormal operating condition occurred. This may indicate that the switch has failed. Consult with your Fujitsu or Fujitsu certified support engineer immediately to correct this condition. Orange Blinking Firmware in the internal flash memory of the switch is destroyed.
-
Page 24: Top Surface
Chapter 1 Getting Started 1.1.4 Top Surface The XG0440DC is used as an example. The front and back direction of the rack mounting brackets attached to the side of the switch is reversed for the XG0440DC and XG0440DCR. Rating Label Warning Sticker Product label... -
Page 25: Bottom Surface
Chapter 1 Getting Started 1.1.5 Bottom Surface The XG0440DC is used as an example. The front and back direction of the rack mounting brackets attached to the side of the switch is reversed for the XG0440DC and XG0440DCR. Product Manufacturing Label •... -
Page 26: Sfp+ Modules
XG0440DC/XG0440DCR Hardware Guide Chapter 1 Getting Started Option 1.2.1 SFP+ Modules SFP+ modules (10GBASE-SR/10GBASE-LR) are available for use. "2.3.3 Connecting Twisted Pair Cable / SFP+ Module", p. 35. Reference User's Guide " SFP+ Module", p. 26. Option... -
Page 27: Chapter 2 Installation
Chapter 2 Installation This chapter describes how to install the switch and connect it to a Console PC. Requirements for Installation Environment ..........28 2.1.1 Installation Requirements . -
Page 28: Requirements For Installation Environment
XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Requirements for Installation Environment Before installing the switch, please check the following: • Make sure that the switch and all the other options shown in this document are available for installation. • All the cables comply with the specifications of the interface connectors. -
Page 29: Space Requirements
XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Installation Requirements The product is specifically designed for rack-mounting. Check-list Check the following items. Check Item Check Result Nothing is put on the switch. Vents are not obstructed. The switch is not located on a table or stacked atop another switch. -
Page 30: Installation Of The Switch
The switch is specifically designed for rack-mounting. The XG0440DC is used as an example. The front and back direction of the rack mounting brackets attached to the side of the switch is reversed for the XG0440DC and XG0440DCR. The XG0440DC is mounted in a rack so that the port side of the switch is located at the front. - Page 31 XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Install the switch in a 19” rack The switch can be installed and operated in the EIA standard 19" rack. Prepare the following rack mounting components attached. • Rack Mounting Rails (1 set): Rails for mounting the switch in a rack.
- Page 32 The XG0440DC is mounted in a rack so that the port side of the switch is located at the front. The XG0440DCR is mounted in a rack so that the power inlet side of the switch is located at the front.
-
Page 33: Connecting The Equipment
XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Connecting the Equipment We recommend discharging static electricity of twisted pair cable before connecting it to the switch. Also see below for how to install USB memory. 2.3.1 Discharging Twisted Pair Cable Discharge static electricity of the twisted pair cable through the ground wire cable (ground wire for power supply, buildings, etc.) using static electricity removal tool, before connecting twisted pair cable to the switch. - Page 34 XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Cleaning of Optical Connector Remove the connector guard cap of optical fiber part, and check the connector end face. If the end face is not clean, clean it with a reel type fiber cleaner.
-
Page 35: Connecting Twisted Pair Cable / Sfp+ Module
XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation 2.3.3 Connecting Twisted Pair Cable / SFP+ Module Below is how to connect twisted pair cable and SFP+ module. Use the crossover cable when connecting with routers and terminals. Use the straight cable in case of cascading connection with other switching HUBs with transmission mode at fixed setting other than auto negotiation. - Page 36 XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Connecting SFP+ Module Firmly install SFP+ module to SFP+ slot and lock module to the switch. SFP+ module Precautions • SFP Module (100BASE-FX, 1000BASE-SX/LX, etc.) cannot be installed. • Safely keep a guard cap of SFP+ module.
- Page 37 XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Precautions Cable length will be as below based on the specification of the optical fiber cable. Type Core/Cladding Diameter Minimum Transimission Band Cable Length (m) 62.5/125 µ m 160MHz/km 200MHz/km 50/125 µ m 400MHz/km...
-
Page 38: Plugging In The Usb Memory
XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation 2.3.4 Plugging in the USB Memory USB memory can be plugged in from the port side of the switch. Caution Do NOT unplug out the memory stick during access. It may result in crashing setting data. -
Page 39: Connecting A Setup Pc
XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Connecting a Setup PC This is to connect a set up PC to the console port of the switch using RS232C cable. Necessary Hardware / Software Please prepare the hardware & software specified below to connect to the switch. - Page 40 XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Turn On the Power If the power of the switch is off, turn it on. Reference "2.7 Turn On/Turn Off the Power", p. 43. It is not necessary to turn off the power when connecting or removing the console cable adapter.
-
Page 41: Time Setting
When setting time and date to be "Jan 1, 2011 12:30:00am" type in command # date 2012/01/01.12:30:00 XG0440DC# configure Switch to Configuration mode. XG0440DC(config)# time zone -0500 When setting time zone to be "-0500". XG0440DC(config)# commit Apply the configuration. XG0440DC(config)# save Save the configuration. -
Page 42: Set Up Ip Address
Eg. When setting the switch through www browser or installing a firmware from the initial state of the purchase. The following commands show how to set up the IP address (ex. 192.168.1.1) Command XG0440# configure XG0440DC(config)# lan 0 ip address 192.168.1.1/24 3 XG0440DC(config)# lan 0 vlan 1 XG0440DC(config)# commit XG0440DC(config)# exit... -
Page 43: Turn On/Turn Off The Power
XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Turn On/Turn Off the Power The following describes the method for turning on and turning off the power of the switch. Caution • Please use the power cable included in this product. Also, please do NOT use this power cable on other products. -
Page 44: Turn Off The Power
XG0440DC/XG0440DCR Hardware Guide Chapter 2 Installation Power LED of PSU1 and PSU1 LED of the switch will light in green. Next, plug in the power cable to the power connecter of PSU2. The Power LED of PSU2 and PSU2 LED of the switch will light in green. -
Page 45: Index
XG0440DC/XG0440DCR Hardware Guide Index Index Number 10/100/1000BASE-T Port ........18 Option ............... 26 organization of the manuals ........8 Bottom Surface ............25 Part No.,Serial No. with barcode label ..... 24 Power Cables ............17 Power Inlet ............... 22 CD-ROM ..............17 POWER LED ............ - Page 46 XG0440DC/XG0440DCR Hardware Guide Index USB Memory ............38 USB Port ..............19 Warning Sticker ............24...
- Page 47 Printed in Japan • The contents may be revised without prior notice. • Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. • No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.