Toshiba TOSVERT VF-A7 Instruction Manual page 224

[28] Protection functions
Communi
Title Function
cation No
 0600 Motor overload protection level #1 10 100 [%]
 0601 Stall prevention level
0602 Selection of inverter trip holding

 0603 Emergency stop
Emergency DC injection
 0604
braking control time
0605 Output phase failure detection 0: Disabled, 1: Enabled

0606 Overload reduction start-up frequency 0.0 30.0 [Hz]

 0607 Motor 150%-overload time limit 10 2400 [s]
Relay injection timing for
 0608
rush-current suppression
0609 Mode of rush-current suppression relay 0: Standard, 1: in relation to ST

0610 Low current trip

 0611 Low current detection level
 0612 Low current detection time
Detection of output short-
0613

circuit during start-up
Adjustment of detection pulse for
0614 output short-circuit during start-up 1 100 [ s]

 0615 Over-torque trip
Over-torque detection level
 0616
during power running
Over-torque detection level
0617

during regeneration
0618 Over-torque detection time

 0620 Cooling fan control mode
 0621 Cumulative operation time alarm setting 0.1 999.9 [ 100h]
0622 Abnormal speed detection filter 0.01 100.0 [s] (*1)

0623 Over-speed detection frequency range 0: Disabled, 0.1 30.0 [Hz]

 0624 Speed drop detection frequency range 0: Disabled, 0.1 30.0 [Hz]
Over-voltage stall protection
 0625
level (high response)
0626 Over-voltage stall protection level 50 250 [%]

0627 Under-voltage trip mode

 0628 Under-voltage detection time 0.00 10.00 [s]
 0629 Under-voltage stall level
0630 System-supporting sequence(B-timer)

0631 Position deviation limit

 0632 Brake release inhibition time after run 0.00: Setting of  is valid, 0.01 2.50 [s]
The trip selection at the VI/II
 0633
low-level input
(*1): Set a time longer than the acceleration/deceleration time.
(Reference section): Refer to the inverter's individual manual.
Adjustment range
0 199 [%], 200: Disabled
0: Cleared if power is turned off
1: Held even if power is turned off
0: Coast stop 1: Deceleration stop
2: Emergency DC injection braking stop
3: Coast stop without FL output
4: Deceleration stop without FL output
5: Emergency DC injection braking without FL output
0.0 10.0 [s]
0.3 2.5 [s]
0: Disabled, 1: Enabled
0 100 [%]
0 255 [s]
0: Standard
1: Only one time at power injection or at first start after reset
0: Disabled, 1: Enabled
0 250 [%]
0 250 [%]
0.0 100.0 [s]
0: Automatic, 1: Always ON
50 250 [%]
0: Disabled, 1: Enabled
50 100 [%]
0.0: Invalid, 0.1 10.0 [s]
0.1 6553
0 100
Sensorless vector/vector with sensor ( valid,
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
1/0.01 100 Enabled /
1/0.01 150 Enabled /
0 Disabled /
0 Disabled /
0.1/0.01 0.1 Enabled /
0 Disabled /
0.01/0.01 6.0 Enabled /
1/1 600 Enabled /
0.1/0.01 0.3 Disabled /
0 Disabled /
0 Disabled /
1/0.01 0 Enabled /
1/1 0 Enabled /
0 Disabled /
1/1 50 Disabled /
0 Enabled /
1/0.01 150 Enabled /
1/0.01 150 Enabled /
0.1/0.01 0.5 Enabled /
0 Enabled /
0.1/0.1 175.0 Enabled /
0.01/0.01 10.00 Enabled /
0.01/0.01 0.0 Enabled /
0.01/0.01 0.0 Enabled /
1/0.01 135 Enabled /
1/0.01 130 Enabled /
0 Disabled /
0.01/0.01 0.03 Disabled /
1/0.01 75 Enabled /
0.1/0.01 0.0 Enabled /
0.1/0.1 16 Disabled
0.01/0.01 0.00 Disabled /
1/1 0.00 Enabled /
:invalid)
Vector control
V/f Reference
Torque Position
Constant section
control control
/ / 5.13
/ / 6.25.2
/ / 6.25.3
/ / 6.25.4
/ / 6.25.4
/ /
/ / 5.13
/ / 5.13
/ /
/ /
/ / 6.25.7
/ / 6.25.7
/ / 6.25.7
/ / 6.25.8
/ / 6.25.8
/ / 6.25.9
/ / 6.25.9
/ / 6.25.9
/ / 6.25.9
/ / 6.2510
/ / 6.25.11
/ / /
/ /
/ /
6.13.5
6.13.5
/ / 6.25.13
/ / 6.25.14
/ / 6.25.15
/ /
/
/ /
/ /