Toshiba TOSVERT VF-A7 Instruction Manual page 217

[16] Functions for lift (2/2)
Communi
Title
cation No
0340 Heavy load torque during fixed speed in reverse direction

0341 Automatic light-load high-speed operation frequency

[17] Commercial/inverter switching function
Communi
Title Function
cation No
Output signal selection of
 0354 commercial power/inverter
switching
Commercial power/inverter
 0355
switching frequency
 0356 Inverter side switching waiting time Model dependent 10.00 [s]
Commercial power side
0357

switching waiting time
Commercial power switching
 0358
frequency holding time
[18] PID control
Communi
Title Function
cation No
 0360 Signal selection of PID control 0: PID control disabled, 1: VI/II, 2: RR, 3: RX, 4: RX2
0361 Delay filter

 0362 Proportional (P) gain
0363 Integral (I) gain

 0364 PID deviation upper limit
0365 PID deviation lower limit

 0366 Differential (D) gain
[19] Speed feedback/positioning control
Communi
Title Function
cation No
 0367 Number of PG input pulses
0368 Number of PG input phases

0369 PG disconnection detection

 0370 Electronic gear
0371 Position loop gain

 0372 Positioning completion range 1 4000
0373 Frequency limit at position control 1 8000 [Hz/s], 8001: disabled

(Reference section): Refer to the inverter's individual manual.
Function Adjustment range
0 250 [%]
30.0  [Hz]
Adjustment range
0: OFF, 1: Automatic switching in case of trip
2: Commercial power switching frequency setting
enabled
3: Both (1+2)
0  [Hz]
0.37 10.00 [s]
0.1 10.0 [s]
Adjustment range
0 255
0.01 100.0
0.01 100.0
0 50 [%]
0 50 [%]
0.00 2.55
Adjustment range
1 9999
1: Single-phase input, 2: Two-phase input
0: Disabled, 1: Enabled
100 to 4000 pulses/rotation
0.0 100.0
Sensorless vector/vector with sensor ( valid,
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
1 100 Enabled /
0.01/0.01 80.0 Enabled /
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0 Disabled /
0.01/0.01 60.0 Enabled /
0.01/0.01 See J-28 Enabled /
0.01/0.01 0.62 Enabled /
0.1/0.01 2.0 Enabled /
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0 Enabled /
0 Enabled /
0.01/0.01 0.1 Enabled /
0.01/0.01 0.1 Enabled /
1/0.01 50 Enabled /
1/0.01 50 Enabled /
0.01/0.01 0 Enabled /
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
1/1 500 Disabled /
2 Disabled /
0 Disabled /
1/1 1000 Disabled
0.1/0.01 4.0 Enabled
1/1 100 Enabled
1/1 800 Disabled
:invalid)
Vector control
V/f Reference
Torque Position
Constant section
control control
Vector control
V/f Reference
Torque Position
Constant section
control control
/ 6.16
/ 6.16
/ 6.16
/ 6.16
/ 6.16
Vector control
V/f Reference
Torque Position
Constant section
control control
Vector control
V/f Reference
Torque Position
Constant section
control control
/ /
/ /
/ /
/
/
/
/