Toshiba TOSVERT VF-A7 Instruction Manual page 214

[7] Speed/torque reference gain/bias setup (2/2)
Communi
Title Function
cation No
 0228 BIN reference point #1
0229 BIN reference point #1 frequency -  [Hz] (*1)

 0230 BIN reference point #2
0231 BIN reference point #2 frequency -  [Hz] (*1)

0232 BIN reference point #1 rate

0233 BIN reference point #2 rate

0234 Pulse reference point #1

 0235 Pulse reference point #1 frequency -  [Hz] (*1)
0236 Pulse reference point #2

 0237 Pulse reference point #2 frequency -  [Hz] (*1)
(*1): Adjustment range is -327.68 327.67 [Hz] in case of 16-bit access.
[8] Operation frequency
Communi
Title Function
cation No
0240 Start-up frequency

 0241 Run frequency
0242 Run frequency hysteresis

 0243 Stop frequency
0244 0 Hz dead band frequency

[9] DC injection braking
Communi
Title Function
cation No
 0250 DC injection braking start frequency 0.0 120.0 [Hz]
0251 DC injection braking current

 0252 DC injection braking time
0253 Forward/reverse DC braking priority control 0: OFF, 1: ON

 0254 Motor shaft fixing control
0255 Zero-speed stop mode selection 0: Standard(DC injection breaking), 1: 0Hz command

[10] Jogging operation
Communi
Title Function
cation No
0260 Jog run frequency

 0261 Jog stop control
(Reference section): Refer to the inverter's individual manual.
Adjustment range
-100 100 [%]
-100 100 [%]
-250 250 [%] (For torque control, etc.)
-250 250 [%] (For torque control, etc.)
-100 100 [%]
-100 100 [%]
Adjustment range
0.0 10.0 [Hz]
0.0  [Hz]
0.0 30.0 [Hz]
0.0 30.0 [Hz]
0.0 5.0 [Hz]
Adjustment range
0.0 100.0 [%]
0.0 10.0 [s]
0: Disabled, 1: Enabled
Adjustment range
0.0 20.0 [Hz]
0: Deceleration stop
1: Coast stop
2: DC injection braking stop
Sensorless vector/vector with sensor ( valid,
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
1/0.01 0 Enabled /
0.01/0.01 0.0 Enabled /
1/0.01 100 Enabled /
0.01/0.01 80.0 Enabled /
1/0.01 0 Enabled /
1/0.01 100 Enabled /
1/0.01 0 Enabled /
0.01/0.01 0.0 Enabled /
1/0.01 100 Enabled /
0.01/0.01 80.0 Enabled /
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0.01/0.01 0.1 Enabled /
0.01/0.01 0.0 Enabled /
0.01/0.01 0.0 Enabled /
0.01/0.01 0.0 Enabled /
0.01/0.01 0.0 Enabled /
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0.01/0.01 0.0 Enabled /
0.1/0.01 50.0 Enabled /
0.1/0.01 1.0 Enabled /
0 Enabled /
0 Enabled /
0 Disabled /
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0.01/0.01 0.0 Enabled /
0 Enabled /
:invalid)
Vector control
V/f Reference
Torque Position
Constant section
control control
/
/
/
/
Vector control
V/f Reference
Torque Position
Constant section
control control
6.7.1
6.7.2
6.7.2
6.7.1
6.7.3
Vector control
V/f Reference
Torque Position
Constant section
control control
6.8.1
6.8.1
6.8.1
6.8.1
6.8.2
6.8.3
Vector control
V/f Reference
Torque Position
Constant section
control control
6.9
6.9