Panel Description; Front Panel - Icom MR-1000RII Instruction Manual

1

PANEL DESCRIPTION

■ Front panel

q POWER SWITCH [POWER]/[
Push to turn the radar power ON or OFF.
• The standby screen appears for 90 seconds while the
magnetron warms up.
• The initial screen appears and a beep sounds after the
power has been turned ON.
w TRANSMIT/SAVE SWITCH [TX (SAVE)]/
[ ]
➥ Push to toggle between the TX mode and the
standby mode. (p. 8)
➥ Hold down for 1 second to turn ON the power
save function. The radar for TX interval scan is
fixed at 10 revolutions. (p. 11)
• Select the save time in INT. SETTING menu.
e RANGE UP/ DOWN SWITCHES [+]/[–]/
[ ]/[
Push [+] to increase the screen range.
Push [–] to decrease the screen range.
r UP, DOWN, LEFT, RIGHT KEYS [p] [q] [t] [u]
Set the EBLs, VRMs, alarm area, ATA target, etc.
according to the key pushed.
Use [p] [q] to select menu item and [t] [u] to set
the item.
Using [p] [t]/[p] [u] or [q] [t]/[q] [u] combina-
tion allows you to move the cross line cursor to the
upper (or lower) left or right.
1
MARINE RADAR GAIN
POWER
TX
SEA
SAVE
RAIN
MOB
TARGET TRAILS
ZOOM
ALM MODE
OFF CENT
EBL1 EBL2
VRM1 VRM2
PI
BRILL MENU
HL OFF
] (p. 7)
] (p. 8)
GAIN
POWER
!3
TX
SEA
SAVE
!4
+
RAIN
-
!5
!6
MOB
!7
TARGET TRAILS
ZOOM
!8
ALM MODE
OFF CENT
EBL1 EBL2
!9
VRM1 VRM2
PI
@0
BRILL MENU
HL OFF
Control panel (English)
t TRAILS SWITCH [TRAILS]/[
Push to toggle the trail function ON or OFF. This is
useful for watching other ship's tracks, approximate
relative speed.
• Trail Time can be set in VIDEO menu.
y ZOOM FUNCTION [ZOOM]/[
Push [TARGET]/[
multaneously to toggle the ZOOM function ON or
OFF. The ZOOM function enlarges the target to two
times normal size.
• Move the cursor to the target, then turn ON the function.
• The screen zooms the middle of the screen around own
ship.
• This function is not available on the
higher ranges.
u MODE SWITCH [MODE]/[
Push to select the Head-up (H UP), Course-up (C
UP), North-up (N UP) or True motion (TM) screens.
• The North-up and Course-up screens can be selected
only when a bearing data input is connected. (p. 38)
• The TM screen requires bearing data and LOG or posi-
tion data. (p. 38)
• TheTM screen is not selectable on the 32 NM or higher
range.
i OFF CENTER FUNCTION [OFF CENT]/[
(p. 9)
Push [ALM]/[
neously to turn the OFF CENTER function ON or
OFF.
• This function is usable on 24NM or less ranges.
q
!3
w
!4
e
!5
!6
r
t
!7
y
u !8
i
o !9
!0
!1
@0
!2
Control panel (Chinese)
] (p. 11)
] (p. 10)
] and [TRAILS]/[
1 ⁄ and the 32 NM or
8
]
] and [MODE]/[ ] simulta-
q
w
e
r
t
y
u
i
o
!0
!1
!2
] si-
]