[Color]; [Tint]; [Color Temperature]; [Color] [0] - Panasonic PT-DZ770E Operating Instructions Manual

[PICTURE] menu

[COLOR]

You can adjust the color saturation of the projected
image.
1) Press ▲▼ to select [COLOR].
2) Press ◀▶ or the <ENTER> button.
▶
z The [COLOR] individual adjustment screen is
displayed.
3) Press ◀▶ to adjust the level.
Operation
Press ▶ .
Press ◀ .

[TINT]

You can adjust the skin tone in the projected image.
1) Press ▲▼ to select [TINT].
2) Press ◀▶ or the <ENTER> button.
▶
z The [TINT] individual adjustment screen is
displayed.
3) Press ◀▶ to adjust the level.
Operation
Adjusts skin tone
Press ▶ .
toward greenish
color.
Adjusts skin tone
Press ◀ .
toward reddish
purple.

[COLOR TEMPERATURE]

You can switch the color temperature if the white
areas of the projected image are bluish or reddish.
1) Press ▲▼ to select [COLOR
TEMPERATURE].
2) Press ◀▶ or the <ENTER> button.
▶
z The [COLOR TEMPERATURE] individual
adjustment screen is displayed.
3) Press ◀▶ to switch [COLOR
TEMPERATURE].
▶
z The setting will change as follows each time
you press the button.

[DEFAULT]

[HIGH]
Note
z When [COLOR MATCHING] (
48 - ENGLISH
Adjustment Range
Maximum
Deepens colors.
value +31
Minimum
Weakens colors.
value –31
Adjustment Range
Maximum
value +31
Minimum
value –31
[USER]
[MIDDLE]
page 58)

adjustment is set to other than [OFF], [COLOR
TEMPERATURE] is fixed to [USER].
■ To adjust desired white balance ▶
4) Select [USER] in Step 3).
5) Press the <ENTER> button.
▶
z The [COLOR TEMPERATURE] screen is
displayed.
6) Press ▲▼ to select [WHITE
BALANCE].
7) Press the <ENTER> button.
▶
z The [WHITE BALANCE] screen is displayed.
8) Press ▲▼ to select [WHITE BALANCE
HIGH] or [WHITE BALANCE LOW].
9) Press the <ENTER> button.
▶
z The [WHITE BALANCE HIGH] screen or the
[WHITE BALANCE LOW] screen is displayed.
10) Press ▲▼ to select [RED][GREEN]
[BLUE].
11) Press ◀▶ to adjust the level.
Item Operation
Press ▶ .
[RED]
Press ◀ .
Press ▶ .
[GREEN]
Press ◀ .
Press ▶ .
[BLUE]
Press ◀ .
Note
z Adjust [COLOR TEMPERATURE] correctly. All
colors will not be displayed properly unless adequate
adjustment is made. If the adjustment does not look
suitable, you can press the <DEFAULT> button
on the remote control to return the setting for the
selected item only to the factory default setting.
z The setting of [COLOR TEMPERATURE] is not
reflected in internal test patterns (
Make sure to set [COLOR TEMPERATURE] while
projecting input signal.
■ To change the [USER] name ▶
4) Select [USER] in Step 3).
5) Press the <ENTER> button.
▶
z The [COLOR TEMPERATURE] screen is
displayed.
6) Press ▲▼ to select [COLOR
TEMPERATURE NAME CHANGE].
Adjustment Range
Deepens
Maximum
red.
value
High: 255
Weakens
Low: 63
red.
Deepens
Minimum
green.
value
High: 0
Weakens
Low: 0
green.
Deepens
Default
blue.
High: 255
Weakens
Low: 32
blue.
page 75).
