Table of Contents
Advertisement
Thank you for purchasing this Panasonic product.
■ This manual is common to all the models regardless of suffixes of the Model No.
z S: Silver model, the standard zoom lens supplied
K: Black model, the standard zoom lens supplied
■ Before operating this product, please read the instructions carefully and save this manual
for future use.
■ Before using your projector, be sure to read "Read this first!" (
Operating Instructions
DLP
Projector
TM
Model No.
LS: Silver model, the lens sold separately
LK: Black model, the lens sold separately
Functional Manual
Commercial Use
PT-DZ770E
PT-DZ770EL
pages 2 to 8).
ENGLISH
TQBJ0443-1
Advertisement
Chapters
Table of Contents
Related Manuals for Panasonic PT-DZ770E
Summary of Contents for Panasonic PT-DZ770E
-
Page 1: Operating Instructions
PT-DZ770E Model No. PT-DZ770EL Thank you for purchasing this Panasonic product. ■ This manual is common to all the models regardless of suffixes of the Model No. z S: Silver model, the standard zoom lens supplied LS: Silver model, the lens sold separately... -
Page 2: Read This First
Information Read this first! Read this first! WARNING: THIS APPARATUS MUST BE EARTHED. WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779. - Page 3 Read this first! IMPORTANT: THE MOULDED PLUG (U.K. only) FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362.
- Page 4 Read this first! WARNING: „ POWER The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible when problems occur. If the following problems occur, cut off the power supply immediately. Continued use of the projector in these conditions will result in fire or electric shock. z If foreign objects or water get inside the projector, cut off the power supply.
- Page 5 If liquid enters inside of the projector, consult your dealer. z Particular attention must be paid to children. Use the ceiling mount bracket specified by Panasonic. Using the ceiling mount bracket other than the specified one will result in falling accidents.
- Page 6 Read this first! WARNING: „ ACCESSORIES Do not use or handle the batteries improperly, and refer to the following. Failure to observe this will cause burns, batteries to leak, overheat, explode or catch fire. z Use AA/R6 batteries. z Do not use unspecified batteries. z Do not use chargeable batteries.
- Page 7 Read this first! CAUTION: „ ON USE/INSTALLATION Do not place heavy objects on top of the projector. Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or injury. The projector will be damaged or deformed. Do not put your weight on this projector.
-
Page 8: Remote Control Battery
Read this first! To remove the battery Remote Control Battery 1. Press the guide and lift the cover. 2. Remove the batteries. (ii) Trademarks • Microsoft ® , Windows ® , Windows Vista ® , and Internet Explorer ® are the registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. - Page 9 Features of the Projector Features of the Projector Quick Steps Quick Steps For details, see the corresponding pages. High luminance & High color reproducibility 1. Set up the projector. ▶ The unique optical system and page 23) lamp drive system achieve a high luminance and high color reproducibility.
-
Page 10: Table Of Contents
Contents Be sure to read “Read this first!”. ( pages 2 to 8) Contents Adjustment range by the lens position shift Important Information (optical shift) ..........40 Remote control operation ......41 Read this first! ..........2 Using the shutter function ........ 41 Precautions for use ........12 Using the on-screen display function .... - Page 11 Contents [AUTO SIGNAL] ..........60 [NETWORK SETUP] ........82 [AUTO SETUP] ..........60 [NETWORK CONTROL] .........82 [RGB IN] ............61 [NETWORK STATUS] ........82 [DVI-D IN] ............61 Network connections ........83 [HDMI IN] ............62 Accessing from the Web browser ....85 [ON-SCREEN DISPLAY] .........62 Maintenance [BACK COLOR] ..........63 [STARTUP LOGO] ..........63 Lamp/Temperature/Filter Indicators ..102...
-
Page 12: Precautions For Use
Precautions for use Precautions for use Cautions when transporting z The projection lens is susceptible to effects from vibration or impact. Make sure to remove the lens when transporting. Use a protective cover to avoid the effects of dust to the set or projection lens. z When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. - Page 13 Precautions for use ■ Cautions when setting up the projector ▶ z To install and use the projector via a method that does not use the adjustable feet in a floor standing installation, fix the projector using the five screw holes for ceiling mounting (as shown in the diagram). (Screw diameter: M6, tapping depth inside the set: 12 mm (15/32"), torque: 4 ±...
-
Page 14: Security
▶ z Change your password periodically. ▶ z Panasonic Corporation or its affiliate companies will never ask for your password directly. Do not divulge your password in case you receive such inquiries. ▶ z The connecting network must be secured by a firewall, etc. -
Page 15: Cautions On Use
For license conditions related to software in (2) and (3), refer to the provisions of the software licenses (GNU GENERAL PUBLIC LICENSE and GNU LESSER GENERAL PUBLIC LICENSE) in the supplied CD-ROM. If you have any questions regarding the software, please contact us via email (sav.pj.gpl.pavc@ml.jp.panasonic.com). Pursuant to at the directive 2004/108/EC, article 9(2) -
Page 16: Accessories
Precautions for use Accessories Make sure that the following accessories are provided with your projector. Numbers enclosed in < > show the number of accessories. Wireless/wired remote Power cord <1> Power cord <1> Projection lens cover <1> control unit <1> (K2CM3FZ00003) (K2CT3FZ00003) (TKPB35101) -
Page 17: Optional Accessories
Precautions for use ■ Contents of the supplied CD-ROM The contents of the supplied CD-ROM are as follows. Instruction/list (PDF) Software ▶ ▶ zOperating Instructions - Functional z Multi Projector Monitoring & Control Manual Software (Windows) –▶This software allows you to monitor and control ▶... -
Page 18: Start-Up Display
Start-up display Start-up display The initial setting screen is displayed when the projector is switched on for the first time after purchase as well as when [INITIALIZE] – [ALL USER DATA] ( page 74) is executed. Set them in accordance with circumstances. ... -
Page 19: About Your Projector
About your projector About your projector Remote control ■ Top ▶ (1) Remote control indicator Flashes if any button in the remote control is pressed. Remote control signal transmitter (2) Power standby < > button Sets the projector to the standby mode when the <MAIN POWER> switch on the projector is set to <ON>. -
Page 20: Projector Body
About your projector Projector body ■ Front ▶ (1) Power indicator<ON (G)/STANDBY (R)> Displays the status of the power. (2) Lamp indicator <LAMP1> (1) (2) (3) (4) (5) Displays the status of lamp 1. (3) Lamp indicator <LAMP2> Displays the status of lamp 2. (4) Temperature indicator <TEMP>... -
Page 21: Control Panel
About your projector ■ Control panel ▶ (10) (11) (12) (13) (14) (1) Power standby < > button (9) <MENU> button Sets the projector to the standby mode when the <MAIN Displays and erases the main menu. POWER> switch on the projector is set to <ON>. Returns to the previous screen when a sub-menu is displayed.( page 44) -
Page 22: Using The Remote Control
Using the remote control Using the remote control z The ID number set on the remote control will Inserting and removing the be stored unless it is set again. However, it will batteries be erased if the remote control is left with dead batteries. -
Page 23: Setting Up
Setting up Setting up Projection method You can use the projector with any of the following four projection methods. Select the appropriate method depending on the environment. ■ Mounting on the ceiling and ▶ ■ Setting on a desk/floor and ▶... -
Page 24: Screen Size And Throw Distance
Setting up Screen size and throw distance Refer to the following figures and table describing projection distances to install the projector. Image size and image position can be adjusted in accordance with the screen size and screen position. Projection screen Screen Screen L (LW/LT) - Page 25 Setting up ■ Projection distance per projection lens ▶ ▶ zWhen the screen aspect is 16:10 (unit: m) (The dimensions of the following table contain slight error.) Optional lens Standard Lens type Fixed-focus Ultra-short focus Short focus Medium focus Zoom lens Lens Zoom lens Zoom lens...
- Page 26 Setting up ▶ zWhen the screen aspect is 16:9 (unit: m) (The dimensions of the following table contain slight error.) Optional lens Standard Lens type Fixed-focus Ultra-short focus Short focus Medium focus Zoom lens Lens Zoom lens Zoom lens Zoom lens Projection lens Model No.
- Page 27 Setting up ▶ zWhen the screen aspect is 4:3 (unit: m) (The dimensions of the following table contain slight error.) Optional lens Standard Lens type Fixed-focus Ultra-short focus Short focus Medium focus Zoom lens Lens Zoom lens Zoom lens Zoom lens Projection lens Model No.
- Page 28 Setting up ■ Projection distance formulas by projection lens ▶ To use a screen size not listed in this manual, check the screen size SD and use the following formula to calculate projection distance. The unit of the calculation result is m. Lens type Aspect ratio Projection distance (L) formula...
-
Page 29: Adjusting Adjustable Feet
Setting up Adjusting adjustable feet Install the projector on a flat surface so that the front of the projector is parallel to the screen surface and the projection screen is rectangular. If the screen is tilted downward, the projection screen can be adjusted to be rectangular by adjusting the adjustable feet. -
Page 30: Removing/Attaching A Projection Lens
Removing/attaching a projection lens Removing/attaching a projection lens Attach and remove the projection lens in the same way as a standard zoom lens and optional accessories. Move the projection lens to the home position before replacing or removing the lens. ( page 40) ... -
Page 31: Attaching The Projection Lens
Removing/attaching a projection lens Attaching the projection lens 1) Remove the projection lens cover and insert fully by aligning the projection lens guide with the projector guide grooves. Guide groove Guide Projection lens 2) Turn the projection lens clockwise until it clicks. 3) Attach the projection lens cover aligning the marking (groove *1) to the tip of the arrow on the projector (*2), and then turn and secure the projection lens cover until the *1 groove aligns with the *3 marking. -
Page 32: Connections
Connections Connections Before connecting to the projector z Before connecting, carefully read the operating instructions for the external device to be connected. z Turn off the power of all devices before connecting cables. z Acquire any connection cable necessary to connect the external device to the system that is either not supplied with the device or not available as an option. -
Page 33: Connecting Example: Av Equipment
Connections ■ <HDMI IN> terminal pin assignments and signal names ▶ Pin No. Signal name Pin No. Signal name Outside view T.M.D.S data 2+ (11) T.M.D.S clock shield T.M.D.S data 2 shield (12) T.M.D.S clock– Even-numbered pins (2) to (18) T.M.D.S data 2–... -
Page 34: Connecting Example: Computers
Connections Connecting example: Computers Note z Use an HDMI cable that conforms to HDMI standards such as an HDMI High Speed cable. If a cable that does not meet HDMI standards is used, video may be interrupted or may not be displayed. z The <HDMI IN>... -
Page 35: Switching On/Off The Projector
Switching on/off the projector Switching on/off the projector Connecting the power cord Make sure that the supplied power cord cover is securely fixed to the projector to prevent removal of the power cord. Confirm that the <MAIN POWER> switch is on the <OFF> side before connecting the power cord. For details of power cord handling, refer to “Read this first!”... -
Page 36: Power Indicator
Switching on/off the projector Power indicator Displays the status of the power. Check the <ON (G)/STANDBY (R)> status of the power indicator before operating the projector. Power indicator <ON (G)/STANDBY (R)> Indicator status Status No illumination or flashing The main power is switched off. The power is switched off. -
Page 37: Switching On The Projector
Switching on/off the projector 8) 10) 11) 12) 4) 11) 10) 12) Switching on the projector Making adjustments and selections To use a projection lens that is an optional accessory, attach the lens before switching on the projector. It is recommended that images are projected page 31) ... -
Page 38: Switching Off The Projector
Switching on/off the projector Switching off the projector Direct power off function Even if the <MAIN POWER> switch is <OFF> during 1) Press the power standby < > button. projection or immediately after the luminous lamp is ▶ z The [POWER OFF(STANDBY)] screen is turned off, the electricity stored in the room will drive displayed. -
Page 39: Projecting
Projecting Projecting Check the projection lens attachment ( page 31), external device connection ( page 32) and power cord connection ( page 35), and then switch on the power ( page 37) to start projecting. Select the video for ... -
Page 40: Moving The Lens To The Home Position
Zoom lens Lens type Standard zoom lens, ET-DLE150, ET-DLE250, ET-DLE080 ET-DLE350, ET-DLE450 Standard projection position PT-DZ770E Standard projection position Projection screen width H 0.1 H Projection screen width H 0.1 H 0.1 H 0.1 H... -
Page 41: Remote Control Operation
Remote control operation Remote control operation 2) Press the <ON SCREEN> button again. ▶ z The on-screen display appears. Note z If you press the <MENU> button on the control panel for at least three seconds while the on-screen indication is off, the on-screen display is turned on. Switching the input signal The input for projection can be switched. -
Page 42: Using The Automatic Setup Function
Remote control operation Using the Automatic setup Using the Function button function [DISABLE], [SUB MEMORY], [SYSTEM SELECTOR], [SYSTEM DAYLIGHT VIEW], [FREEZE], or [SIDE The automatic setup function can be used to BY SIDE] operations can be assigned to the automatically adjust the resolution, clock phase, and <FUNCTION>... -
Page 43: Changing The Picture Aspect Ratio
Remote control operation Changing the picture aspect ratio You can toggle through aspect ratios to select the one that is appropriate for the input signal. button Press the <ASPECT> button on the remote control. ▶ z The setting will change as follows each time you press the button. -
Page 44: Menu Navigation
Menu navigation Menu navigation The on-screen menu (Menu) is used to perform various settings and adjustments of the projector. z For some items, press ◀▶ to display an ▶ Navigating through the menu individual adjustment screen with a bar scale as shown in the following diagram. -
Page 45: Main Menu
Menu navigation Note Sub-menu z You cannot reset all the settings to the factory default at a time. The sub-menu of the selected main menu item is z To reset all the settings adjusted in the sub-menu displayed, and you can set and adjust items in the item to the factory default at a time, perform sub-menu. -
Page 46: [Display Option]
Menu navigation ■ [DISPLAY LANGUAGE] ▶ ■ [SIGNAL LIST] ▶ Details ( page 57) Details ( page 76) ■ [DISPLAY OPTION] ▶ ■ [SECURITY] ▶ Sub-menu item Factory default Page Sub-menu item Factory default Page [COLOR MATCHING] [OFF] [SECURITY PASSWORD] [OFF] [COLOR CORRECTION]... -
Page 47: [Picture] Menu
[PICTURE] menu [PICTURE] menu Note Select [PICTURE] from the main menu, and z The factory default picture mode is [GRAPHIC] for select the item from the sub-menu. still image input signals and [STANDARD] for movie Refer to “Navigating through the menu” based input signals. -
Page 48: [Color]
[PICTURE] menu adjustment is set to other than [OFF], [COLOR [COLOR] TEMPERATURE] is fixed to [USER]. ■ To adjust desired white balance ▶ You can adjust the color saturation of the projected image. 1) Press ▲▼ to select [COLOR]. 4) Select [USER] in Step 3). 2) Press ◀▶... -
Page 49: [White Gain]
[PICTURE] menu 7) Press the <ENTER> button. [SHARPNESS] ▶ z The [COLOR TEMPERATURE NAME CHANGE] screen is displayed. You can adjust the sharpness of the projected image. 8) Press ▲▼◀▶ to select the text, and 1) Press ▲▼ to select [SHARPNESS]. press the <ENTER>... -
Page 50: [System Selector]
[PICTURE] menu ▶ zWhen using other movie based input [AI] signals Select [RGB] or [YP You can perform gradation control appropriate for an image to project the image with optimal contrast. Note 1) Press ▲▼ to select [AI]. z Refer to “List of compatible signals” ( page 118) for ... -
Page 51: [Position] Menu
[POSITION] menu [POSITION] menu [ASPECT] Select [POSITION] from the main menu, and select the item from the sub-menu. You can switch the aspect ratio of the image. Refer to “Navigating through the menu” The aspect ratio is switched within the screen range page 44) for the operation of the menu ... -
Page 52: [Zoom]
[POSITION] menu ■ [THROUGH] ▶ Note z Some size modes are not available for certain types Pictures are displayed without changing the of input signals. [DEFAULT] cannot be selected for resolution of the input signals. NTSC signals. ■ [16:9] ▶ z If an aspect ratio which is different from the aspect ratio for the input signals is selected, the pictures When standard signals... -
Page 53: [Clock Phase]
[POSITION] menu 3) Press ▲▼ to select [INTERLOCKED]. [KEYSTONE] 4) Press ◀▶ to switch [INTERLOCKED]. You can correct the trapezoidal distortion that occurs when the projector is installed tilted or when the Set the [VERTICAL] and [OFF] screen is tilted. [HORIZONTAL] zoom ratio. -
Page 54: [Advanced Menu]
[ADVANCED MENU] [ADVANCED MENU] [BLANKING] Select [ADVANCED MENU] from the main menu, and select the item from the sub-menu. The blanking width is adjusted when there are noise Refer to “Navigating through the menu” at the edge of the screen or the image is slightly page 44) for the operation of the menu ... -
Page 55: [Input Resolution]
[ADVANCED MENU] [INPUT RESOLUTION] [EDGE BLENDING] You can adjust to achieve an optimal image when The edge blending function allows multiple projector there is a flickering image or smeared outlines. images to be seamlessly overlapped by using the inclination of the brightness at the overlapped area. 1) Press ▲▼... -
Page 56: [Raster Position]
[ADVANCED MENU] 8) Press ◀▶ to switch [ON]. 18) Press ▲▼ to select [BRIGHT ▶ OUTSIDE]. z A marker for image position adjustment is displayed. The green line is the starting point 19) Press the <ENTER> button. of edge blending adjusted with [START] in Step ▶... -
Page 57: [Display Language] Menu
[DISPLAY LANGUAGE] menu [DISPLAY LANGUAGE] menu Select [DISPLAY LANGUAGE] from the main menu, and display the sub-menu. Refer to “Navigating through the menu” page 44) for the operation of the menu screen. z Press ▲▼ to select a language, and press the <ENTER>... -
Page 58: [Display Option] Menu
[DISPLAY OPTION] menu [DISPLAY OPTION] menu ■ To set [3COLORS] or [7COLORS] ▶ Select [DISPLAY OPTION] from the main menu, and select the item from the sub-menu. 3) Select [3COLORS] or [7COLORS] in Refer to “Navigating through the menu” Step 2). page 44) for the operation of the menu ... -
Page 59: [Color Correction]
[DISPLAY OPTION] menu ■ To use a colorimeter to adjust the ▶ [COLOR CORRECTION] color matching Colors can be adjusted and registered for each input Use a colorimeter that can measure chromaticity signal format. coordinates and luminance to change the colors 1) Press ▲▼... -
Page 60: [Screen Setting]
[DISPLAY OPTION] menu [SCREEN SETTING] [AUTO SETUP] Set the screen size. You can set when adjusting a special signal or When changing the aspect of a projected image, horizontally long (16:9, etc.) signal. correct to the optimum image position for the set 1) Press ▲▼... -
Page 61: [Rgb In]
[DISPLAY OPTION] menu [RGB IN] [DVI-D IN] Set to match the signal to input to the <RGB 1 IN> Switch the setting when the external equipment is terminal. connected to the <DVI-D IN> terminal of the projector and the image is not projected correctly. 1) Press ▲▼... -
Page 62: [Hdmi In]
[DISPLAY OPTION] menu [HDMI IN] [ON-SCREEN DISPLAY] Switch the setting when the projector is connected to Set the on-screen display. an external device via an HDMI cable and the image 1) Press ▲▼ to select [ON-SCREEN is not projected correctly. DISPLAY]. -
Page 63: [Back Color]
You can set the display/hide of the warning message. [NONE] ▶ z The setting will change as follows each time you press the button. [DEFAULT The Panasonic logo is projected. LOGO] [ON] [OFF] The picture registered by the user [USER LOGO] is projected. -
Page 64: [Shutter Setting]
[DISPLAY OPTION] menu [SHUTTER SETTING] [FREEZE] Set opening/closing of the shutter when power is The projected image is paused temporarily regardless turned on and after the power is turned off. of the playback of the external equipment. 1) Press ▲▼ to select [SHUTTER 1) Press ▲▼... -
Page 65: [Cut Off]
[DISPLAY OPTION] menu [CUT OFF] Each red, green and blue color component can be removed. 1) Press ▲▼ to select [CUT OFF]. 2) Press the <ENTER> button. ▶ z The [CUT OFF] screen is displayed. 3) Press ▲▼ to select [RED], [GREEN], or [BLUE]. -
Page 66: [Projector Setup] Menu
[PROJECTOR SETUP] menu [PROJECTOR SETUP] menu [PROJECTION METHOD] Select [PROJECTOR SETUP] from the main menu, and select the item from the sub-menu. Set the projection method in accordance with the Refer to “Navigating through the menu” installation status of the projector. page 44) for the operation of the menu ... -
Page 67: [Cooling Condition]
[PROJECTOR SETUP] menu [COOLING CONDITION] Note z The speed of the fan increases and the operation sound becomes louder when set to [ON]. Change the fan control depending on the direction of projection. Set [COOLING CONDITION] correctly in accordance [LAMP SELECT] with the direction of projection referencing the following figure. -
Page 68: [Lamp Relay]
[PROJECTOR SETUP] menu [LAMP RELAY] [LAMP POWER] The lamp to be turned on can be automatically Switch lamp brightness according to the operating switched by specifying the day of the week and time. environment or purpose of the projector. The degradation of the lamp due to continuous usage 1) Press ▲▼... -
Page 69: [Schedule]
[PROJECTOR SETUP] menu 9) Press ▲▼ to select [COMMAND]. [SCHEDULE] 10) Press ◀▶ to switch [COMMAND]. Set the command execution schedule for each day of ▶ z The setting will change as follows each time the week. you press the button. 1) Press ▲▼... -
Page 70: [Startup Input Select]
[PROJECTOR SETUP] menu z To delete a command already set, press the [RS-232C] <DEFAULT> button on the Step 6) screen, or select [DELETE] on the Step 7) screen and press the Set the communication conditions of the <SERIAL <ENTER> button. IN>/<SERIAL OUT>... -
Page 71: [Remote2 Mode]
[PROJECTOR SETUP] menu ▶ z The setting will change as follows each time [REMOTE2 MODE] you press the button. You can set the <REMOTE 2 IN> terminal. [ON] [OFF] 1) Press ▲▼ to select [REMOTE2 MODE]. Returns the response when the ID 2) Press ◀▶... -
Page 72: [Status]
[PROJECTOR SETUP] menu [NUMBER [STATUS] Displays the number of registered OF ENTRY signals. SIGNAL] Displays the status of the projector. [REMOTE2 Displays the control status of the 1) Press ▲▼ to select [STATUS]. STATUS] REMOTE2. z [MEMORY NO.]: 2) Press the <ENTER> button. Displays the memory number of ▶... -
Page 73: [No Signal Shut-Off]
[PROJECTOR SETUP] menu [NO SIGNAL SHUT-OFF] [DATE AND TIME] You can set the power of the projector automatically Set the time zone, date, and time of the built-in clock to standby if there is no input signal by the specified of the projector. -
Page 74: [Save All User Data]
[PROJECTOR SETUP] menu [SAVE ALL USER DATA] [INITIALIZE] Save the various setting values as a backup in the Return various setting values to their factory default built-in memory of the projector. settings. 1) Press ▲▼ to select [SAVE ALL USER 1) Press ▲▼... -
Page 75: [Test Pattern] Menu
[TEST PATTERN] menu [TEST PATTERN] menu Select [TEST PATTERN] from the main menu. Refer to “Navigating through the menu” page 44) for the operation of the menu screen. z Press ◀▶ to switch. [TEST PATTERN] Displays the test pattern built-in to the projector. Settings of position, size, and other factors will not be reflected in test patterns. -
Page 76: [Signal List] Menu
[SIGNAL LIST] menu [SIGNAL LIST] menu Renaming the registered data Select [SIGNAL LIST] from the main menu. Refer to “Navigating through the menu” page 44) for the operation of the menu 1) Press ▲▼◀▶ to select the signal for screen. -
Page 77: Protecting The Registered Data
[SIGNAL LIST] menu Protecting the registered data Expanding signal lock-in range 1) Press ▲▼◀▶ to select the signal to 1) Press ▲▼◀▶ to select the signal to protect. set. 2) Press the <ENTER> button. 2) Press the <ENTER> button. ▶ ▶... -
Page 78: Managing The Sub Memory List
[SIGNAL LIST] menu ■ To delete the sub memory data ▶ Managing the sub memory list 1) Press ◀▶ on the normal screen (when the menu is not displayed). The projector has a sub memory function that can ▶ z The [SUB MEMORY LIST] screen is displayed. register the multiple image adjustment data, even if it 2) Press ▲▼◀▶... -
Page 79: [Security] Menu
[SECURITY] menu [SECURITY] menu [SECURITY PASSWORD Select [SECURITY] from the main menu, and select the item from the sub-menu. CHANGE] Refer to “Navigating through the menu” page 44) for the operation of the menu Change the security password. screen. 1) Press ▲▼... -
Page 80: [Text Change]
[SECURITY] menu [TEXT CHANGE] [MENU LOCK PASSWORD] Change the text displayed when the text display is Change the menu lock password. enabled by selecting [TEXT] in [DISPLAY SETTING]. 1) Press ▲▼ to select [MENU LOCK 1) Press ▲▼ to select [TEXT CHANGE]. PASSWORD]. - Page 81 [SECURITY] menu ■ [REMOTE CONTROL] ▶ ▶ z You can set the limitation on the control from the remote control. Enables button operations from the [ENABLE] remote control. Disables button operations from [DISABLE] the remote control. 5) Press ▲▼ to select [ENABLE] or [DISABLE], and press the <ENTER>...
-
Page 82: [Network] Menu
[NETWORK] menu [NETWORK] menu Note Select [NETWORK] from the main menu, and z When using a DHCP server, confirm that the DHCP select the item from the sub-menu. server is running. Refer to “Navigating through the menu” z Consult your network administrator regarding the IP page 44) for the operation of the menu ... -
Page 83: Network Connections
[NETWORK] menu Network connections The projector has a network function, and the following operations are available from the computer using the Web control. z Setting and adjustment of the projector z Display of the projector status z Sending of E-mail messages when there is a problem with the projector “Crestron RoomView”... - Page 84 [NETWORK] menu ■ Name and function of network function parts ▶ (1) (2) (3) (1) LAN10/100 lamp (yellow) (3) LAN LINK/ACT lamp (green) Lights on when connected to the 100BASE-TX. Lights on when connected. Flashes when transmitting/receiving data. (2) <LAN> terminal (10BASE-T/100BASE-TX) Used to connect the LAN cable here.
-
Page 85: Accessing From The Web Browser
3) Enter the user name and the password. ▶ z The factory default setting of the user name is user1 (user rights)/admin1 (administrator rights) and the password is panasonic (lower case). 4) Click OK. ▶ z The [Projector status] page is displayed. - Page 86 [NETWORK] menu ■ Items description ▶ (1) Page tab Switches pages by clicking it. (2) [Status] The status of the projector is displayed by clicking this item. (3) [Projector control] The [Projector control] page is displayed by clicking this item. (4) [Detailed set up] The [Detailed set up] page is displayed by clicking this item.
- Page 87 [NETWORK] menu ■ [Projector status] page ▶ Click [Status] → [Projector status]. Displays the status of the projector for the following items. (1) [PROJECTOR TYPE] Displays the type of the projector. (2) [MAIN VERSION] Displays the firmware version of the projector. (3) [POWER] Displays the status of the power.
-
Page 88: Error Information Page
[NETWORK] menu ■ Error information page ▶ When [Error (Detail)] is displayed in the self-diagnosis display of the [Projector status] screen, click it to display the error details. ▶ z The projector may go into the standby status to protect the projector depending on the contents of the error. [OK]: operating properly [FAILED]: a problem occurred [WARNING]: warning... - Page 89 [NETWORK] menu ■ [Network status] page ▶ Click [Status] → [Network status]. The current network setting status is displayed. ■ [Access error log] page ▶ Click [Status] → [Access error log]. The error log on the WEB server is displayed such as access to the pages that do not exist or access with unauthorized user names or passwords.
- Page 90 [NETWORK] menu ■ [Basic control] page ▶ Click [Projector control] → [Basic control]. (1) [POWER] Switches the power on/off. (2) [SHUTTER] Switches between use or not use of the shutter function. (3) [OSD] Switches between on (display)/off (no display) of the on-screen display function.
- Page 91 [NETWORK] menu ■ [Network config] page ▶ Click [Detailed set up] → [Network config]. ▶ z Click [Network config] to display the [CAUTION!] screen. ▶ z The current settings are displayed by pressing the [Next] button. ▶ z The following setting change screen is displayed by pressing the [Change] button. (1) [PROJECTOR NAME] Enter the name of the projector.
-
Page 92: Adjust Clock] Page
[NETWORK] menu ■ [Adjust clock] page ▶ Click [Detailed set up] → [Adjust clock]. (1) [Time Zone] Select the time zone. (2) [Set time zone] Updates the time zone setting. (3) [NTP SYNCHRONIZATION] Set to [ON] to adjust the date and time automatically. (4) [NTP SERVER NAME] Enter the IP address or server name of the NTP server when you set to adjust the date and time... - Page 93 [NETWORK] menu ■ [E-mail set up] page ▶ E-mail address set in advance for use when there is a problem or when the usage time of a lamp reaches a set value. E-mail can be sent to (maximum two locations). Click [Detailed set up] →...
- Page 94 [NETWORK] menu ■ [E-mail set up] page (continued) ▶ (1) [E-MAIL ADDRESS 2] Enter the E-mail address to be sent when two E-mail addresses are to be used. Leave it blank when two E-mail addresses are not to be used. (2) Settings of the conditions to send E-mail Select the conditions to send E-mail to the second E-mail address.
- Page 95 [NETWORK] menu ■ [Authentication set up] page ▶ You can set the authentication items when POP authentication or SMTP authentication is necessary to send an E-mail message. Click [Detailed set up] → [Authentication set up]. (1) [Auth] Select the authentication method specified by your Internet service provider.
-
Page 96: Contents Of Mail Sent
■ Contents of mail sent ▶ ▶ zExample of E-mail sent when E-mail is set The following E-mail is sent when the E-mail settings have been established. === Panasonic projector report(CONFIGURE) === Projector Type : DZ770 Serial No : SH1234567... - Page 97 [NETWORK] menu ▶ zExample of the E-mail sent for an error The following E-mail is sent when an error has occurred. === Panasonic projector report(CONFIGURE) === Projector Type : DZ770 Serial No : SH1234567 ----- check system ----- MAIN CPU BUS...
- Page 98 [NETWORK] menu ■ [Change password] page ▶ Click [Change password]. (1) [Administrator] Used to change the setting of the [Administrator]. (2) [User] Used to change the setting of the [User]. (3) [Next] Used to change the setting of the password. ▶...
- Page 99 [NETWORK] menu ▶ z[User] account (1) [Account] Displays the account to change. (2) [New] [User name] Enter the desired new user name. (Up to 16 characters in single byte) (3) [New] [Password] Enter the desired new password. (Up to 16 characters in single byte) (4) [New] [Password(Retype)] Enter the desired new password again.
- Page 100 [NETWORK] menu ■ [CRESTRON RoomView] page ▶ The projector can be monitored and/or controlled with RoomView. To start the RoomView control page from the Web control screen, you need to access with the administrator rights. (For user rights, the [CRESTRON RoomView] button is not displayed on the Web control screen.) The control page of RoomView is displayed by clicking [CRESTRON RoomView].
- Page 101 [NETWORK] menu ▶ z[Info] page Click [Info] on the control page. (1) [Projector Name] Displays the projector name. (2) [Mac Address] Displays the MAC address. (3) [Lamp Hours] Displays the cumulative operating time (converted value) of the lamps. (4) [Power Status] Displays the status of the power.
-
Page 102: Lamp/Temperature/Filter Indicators
Lamp/Temperature/Filter Indicators Lamp/Temperature/Filter Indicators Managing the indicated problems If a problem should occur inside the projector, the lamp indicators <LAMP1>/<LAMP2> the temperature indicator <TEMP> and the filter indicator <FILTER> will inform you by lighting or flashing. Check the status of the indicators and manage the indicated problems as follows. Attention z When switching off the projector to deal with problems, make sure to follow the procedure in “Switching off the projector”... - Page 103 Lamp/Temperature/Filter Indicators ■ Temperature indicator <TEMP> ▶ Indicator Flashing in red Flashing in red Lighting in red status (1 times) (3 times) Internal temperature is Internal temperature is The cooling fan has Status Warm-up status high (warning) high (standby warning) stopped.
-
Page 104: Maintenance/Replacement
Maintenance/replacement Maintenance/replacement Before maintaining/replacing the unit z Make sure to turn off the power before maintaining or replacing the unit. ( pages 35, 38) z When switching off the projector, make sure to follow the procedures in “Switching off the projector” ( page 38). -
Page 105: Replacing The Unit
Maintenance/replacement 4) Attach the air filter unit to the z Do not disassemble the air filter unit. projector. Note ▶ z The top and bottom of the air filter unit are z Make sure that the air filter unit is properly attached different. -
Page 106: Lamp Unit
Maintenance/replacement ■ Lamp unit ▶ The lamp unit is a consumable component. Check the lamp usage time in [PROJECTOR SETUP] → [STATUS] page 72) in the menu and change the lamp periodically. It is recommended that you request a qualified technician to replace the lamp unit. Consult your dealer. Consult your dealer to purchase a replacement lamp unit (ET-LAD60A (1 bulb), ET-LAD60AW (2 bulbs)). -
Page 107: Replacing The Lamp Unit
Maintenance/replacement ■ Replacing the lamp unit ▶ Attention z When the projector is mounted on the ceiling, do not perform tasks while your face is near the lamp unit. z Make sure to attach the lamp unit and lamp unit cover properly. z If the lamp unit is not installed properly, remove it and then attach it again. -
Page 108: Troubleshooting
Troubleshooting Troubleshooting Review the following points. For details, see the corresponding pages. Problems Points to be checked Page z Is the power plug firmly inserted into the outlet? ― z Is the <MAIN POWER> switch turned <OFF>? z Is the wall outlet supplying electricity? ―... - Page 109 Troubleshooting Problems Points to be checked Page z Is the [CONTROL PANEL] setting in [CONTROL DEVICE SETUP] set to The buttons on the [DISABLE]? control panel do not operate. z Is the <REMOTE 2 IN> terminal used for contact control? z Is the [SYSTEM SELECTOR] selection set correctly? The image does not z Is there a problem with the video tape or other image sources?
-
Page 110: Technical Information
“11 12 21 22 31 32” NAME? Projector name query Returns the name set in [PROJECTOR NAME] of [NETWORK SETUP]. INF1? Manufacturer name query Returns “Panasonic”. INF2? Model name query Returns “DZ770”. INF0? Other information queries Returns information such as version number. -
Page 111: Control Commands Via Lan
3) Generate a 32-byte hash value from the following data using MD5 algorithm. “xxxxxx:yyyyy:zzzzzzzz” xxxxxx Administrator rights user name for Web control (default user name is “admin1”). yyyyy Password of above administrator rights user (default password is “panasonic”). zzzzzzzz 8-byte random number obtained in Step 2) ▶ zCommand transmission method Transmit using the following command formats. - Page 112 Technical information ■ When WEB Control administrator rights password is not set (Non-protect ▶ mode) ▶ zConnection method 1) Obtain the IP address and port number (Initial set value = 1024) of the projector and request for a connection to the projector. You can obtain both the IP address and the port number from the menu screen of the projector.
-
Page 113: Serial In>/
Technical information <SERIAL IN>/<SERIAL OUT> terminal The <SERIAL IN>/<SERIAL OUT> terminal of the projector conforms with RS-232C so that the projector can be connected to and controlled from a computer. ■ Connection ▶ For one projector For multiple projectors Projector 1 connecting terminals Projector 2 connecting terminals D-Sub 9p D-Sub 9p D-Sub 9p...Terminal -
Page 114: Basic Format
Technical information ■ Basic format ▶ Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control. (2 bytes) ID2 characters Semi-colon Colon (1 byte) (2 bytes) (1 byte) Start (1 byte) -
Page 115: Cable Specifications
Technical information ■ Cable specifications ▶ ▶ ▶ zWhen connected to a computer zWhen connected multiple projectors Projector Computer Projector 1 Projector 2 (<SERIAL IN> (DTE (<SERIAL OUT> (<SERIAL IN> terminal) specifications) terminal) terminal) ■ Control commands ▶ The following table lists the commands that can be used to control the projector using a computer. ▶... -
Page 116: Remote 2 In> Terminal
Technical information <REMOTE 2 IN> terminal It is possible to control the projector remotely (by external contact) from a control panel located away from the projector where remote control signals cannot reach. Use the <REMOTE 2 IN> terminal on the connecting terminals of the projector to connect to the control panel. -
Page 117: Two Window Display Combination List
Technical information Two window display combination list Input A RGB1 RGB2 DVI-D HDMI RGB1 RGB2 DVI-D HDMI Still Still VIDEO S-VIDEO Still Still Movie Movie Movie Movie Input B image image image image RGB1 ― ― Still image RGB1 ― ―... -
Page 118: List Of Compatible Signals
Technical information List of compatible signals The following table specifies the types of signals compatible with the projector. Scanning Dots Plug and play frequency Resolution clock Mode Format (Dots) Frequency Horizontal Vertical DVI-D DVI-D DVI-D RGB2 HDMI (MHz) (kHz) (Hz) EDID1 EDID2 EDID3... - Page 119 Note z There are 1 920 x 1 200 display dots for PT-DZ770E. A signal with a different resolution is converted to the number of display dots and displayed. z The “i” at the end of the resolution indicates an interlaced signal.
-
Page 120: Specifications
(including S Horizontal: 15.75 kHz/15.63 kHz, Vertical: 50 Hz/60 Hz video) Horizontal: 15 kHz to 91 kHz, Vertical: 50 Hz to 85 Hz PIAS (Panasonic Intelligent Auto Scanning) system For RGB signals Dot clock frequency 162 MHz or less 525i (480i): 625i (576i): Horizontal: 15.75 kHz, Vertical: 60 Hz... - Page 121 Specifications Model No. PT-DZ770E PT-DZ770EL 1 set (BNC x 5) RGB signals 0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω) <RGB 1 IN> SYNC/HD TTL high impedance, automatic positive/negative polarity compatible terminal VD TTL high impedance, automatic positive/negative polarity compatible signals Y: 1.0 V [p-p] including synchronization signal, P...
-
Page 122: Dimensions
Takes no responsibility for any damage to the projector resulting from use of a ceiling mount bracket not manufactured by Panasonic or the inappropriate choice of location for installation, even if the warranty period of the projector has not expired. -
Page 123: Index
Index Index Removing/attaching a projection lens ………… 30 Renaming the registered data ………………… 76 Accessories ……………………………………… 16 <ID ALL> button Replacing the air filter unit ………………………105 <AC IN> terminal …………………………… 20, 35 Remote control ………………………… 19, 22 Replacing the lamp unit …………………………106 Adjusting adjustable feet …………………………... - Page 124 This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. Environment care information for users in China This symbol is only valid in China. Panasonic Corporation Web Site : http://panasonic.net/avc/projector/ © Panasonic Corporation 2012 W0612NN1062 -YI...