Codepad Medical Report; Codepad Reporting Options; System Status - Aux Power Supply Fail Report; System Status - Aux Power Supply Fail Restore Report - Bosch ICP-CC404 Installation Manual

ICP-CC404 | Installation Guide | 15.0
A Fire Alarm Report (Contact ID Event Code 110) is
sent to the base station receiver when a user presses
[4] and [6] at the same time. A Fire Alarm is audible,
but you can program the alarm as silent by selecting
Option 2 in Location 425 (refer to Section 18.2 System
Options 2 on page 73). A distinct fire sound is emitted
through the horn speaker to indicate this type of
alarm. The fire sound is different than the burglary
sound.
Restore Reports are not sent for this
event.
If Fire Reports are not required, program
Locations 339 and 340 as 0.

15.11 Codepad Medical Report

Program the Codepad Medical Report value in
Location 341 (tens digit) and Location 342 (units
digit).
The default values are 7 (tens) and 13 (units).
A Medical Report (Contact ID Event Code 100) is
sent to the base station receiver when a user presses
[7] and [9] at the same time. A Medical Alarm is
audible, but you can program the alarm as silent by
selecting Option 4 in Location 425 (refer to Section
18.2 System Options 2 on page 73).
Restore Reports are not sent for this
event.
If Medical Reports are not required,
program Locations 341 and 342 as 0.

15.12 Codepad Reporting Options

Use Location 343 to select whether Codepad Alarm
Reports are sent to Receiver 1 (the default),
Receiver 2, or both, Receiver 2 only when Receiver 1
fails, or there is no reporting at all. Table 47 lists the
reporting options.
Table 48: Codepad Alarm Reporting Options
Option Description
0 No Codepad Alarm Reports required
1 Receiver 1
2 Receiver 2
4 Receiver 1 and Receiver 2
8 Receiver 2 only when Receiver 1 fails
15.13 System Status – AUX Power Supply
Fail Report
Program the AUX Power Supply Fail Report value in
Location 344 (tens digit) and Location 345 (units
digit).
The default values are 10 (tens) and 3 (units).
62
System Reporting Information
A System Trouble Report (Contact ID Event Code
300) is sent when either the codepad AUX power
supply or the accessories AUX power supply fails.
The system reports the event approximately 10 sec
after the AUX power supply fails.
15.14 System Status – AUX Power Supply
Fail Restore Report
Program the AUX Power Supply Fail Restore Report
value in Location 346 (tens digit) and Location 347
(units digit).
The default values are 10 (tens) and 8 (units).
A System Trouble Restore Report (Contact ID Event
Code 300) is sent when the failed codepad AUX
power supply or the accessories AUX power supply is
reset. The system reports the event approximately 10
sec after the AUX power supply is reset.
15.15 System Status – AC Fail Report
Program the AC Fail Report value in Location 348
(tens digit) and Location 349 (units digit).
The default values are 10 (tens) and 2 (units).
An AC Fail Report (Contact ID Event Code 301) is
sent to the base station receiver when the AC mains
supply is disconnected for 2 min. If you do not want
an AC Fail Report to be sent until the AC mains
supply is disconnected for 1 hour, select Option 1 in
Location 426 (refer to Section 18.3 System Options 3 on
page 74). If you want to ignore AC Fail, select
Option 2 in Location 426.
15.16 System Status – AC Fail Restore
Report
Program the AC Fail Restore Report value in
Location 350 (tens digit) and Location 351 (units
digit).
The default values are 10 (tens) and 7 (units).
An AC Fail Restore Report is sent when the AC
mains supply is connected continuously for longer
than 2 min.
15.17 System Status – Low Battery Report
Program the Low Battery Report value in
Location 352 (tens digit) and Location 353 (units
digit).
The default values are 10 (tens) and 1 (units).
Bosch Security Systems, Inc. | 12/08 | F01U089401-02
If AC Fail Reports are not required,
program Locations 348 and 349 as 0.
If AC Fail Restore Reports are not
required, program Locations 350 and
351 as 0.