Setting Stay Mode 2 Zones - Bosch ICP-CC404 Installation Manual

If there is no Telco disarming sequence
programmed, an additional two beeps sound after
entering this mode. These two beeps normally
sound after the last digit of the sequence is
shown.
3. Press [STAY][2 6 1][STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
You can suspend the Telco disarming sequence at
any time.
To disable the Telco disarming sequence:
Enter your Master Code and press [3][AWAY][2]
[AWAY][STAY][4][AWAY].
To program the Telco arming sequence – easy
call forward (immediate on):
1. Enter your Master Code and press [3][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [1][AWAY] button to change the Telco
arming sequence. Three beeps sound.
If a call forwarding sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 30 for the indicators and their meanings.
If there is no call forward sequence programmed,
an additional two beeps sound after entering this
mode. These two beeps normally sound after the
last digit of the call forward sequence is
displayed.
3. Press [STAY][1 2 1] and enter the phone number
to which you want calls from the control panel
diverted.
4. Press [STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
Example
If you want to automatically divert all incoming calls
to another telephone number (for example, 9672
1777) when the system is armed in AWAY Mode,
enter:
[2 5 8 0 3][AWAY][1][AWAY][STAY]
[1 2 1 9 6 7 2 1 7 7 7][STAY][2][AWAY]
You can suspend the Telco arming sequence at any
time.
To disable the Telco arming sequence:
Enter your Master Code and press [3][AWAY][1]
[AWAY][STAY][4][AWAY].
To program the Telco disarming sequence – easy
call forward (immediate off):
1. Enter your Master Code and press [3][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
Bosch Security Systems, Inc. | 12/08 | F01U089401-02
ICP-CC404 | Installation Guide | 6.0
2. Press [2][AWAY] to change the Telco disarming
sequence.
Three beeps sound.
If a Telco disarming sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 30 on page 34 for the indicators and their
meanings.
If there is no Telco disarming sequence
programmed, an additional two beeps sound after
entering this mode. These two beeps normally
sound after the last digit of the sequence is
shown.
3. Press [STAY][2 2 1][STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
You can suspend the Telco disarming sequence at
any time.
To disable the Telco disarming sequence:
Enter your Master Code and press [3][AWAY][2]
[AWAY][STAY][4][AWAY].
6.2.5

Setting STAY Mode 2 Zones

This function allows the Master Code holder to select
the zones that are automatically isolated when the
system is armed in STAY Mode 2.
To arm the system in STAY Mode 2, press and hold
[0] until two beeps sound. Refer to Section 6.3.3 on
page 37 or Section 4.5 Arming the System in STAY Mode
2 on page 20 for more information.
To set STAY Mode 2 zones:
1. Enter your Master Code and press [4][AWAY].
Three beeps sound and the STAY indicator
flashes.
2. Enter the number of the zone you want to
automatically isolate and press [STAY].
The corresponding zone indicator flashes.
3. Repeat Step 2 to select each zone.
As you select each zone to isolate, the
corresponding zone indicator flashes. If
you make a mistake, enter the incorrect
zone number and press [STAY]. This
zone is no longer selected to be isolated
and the zone indicator is extinguished.
4. Press [AWAY].
Two beeps sound and the system returns to the
disarmed state.
The indicators for the zones you selected and the
STAY indicator turn off.
Example
If you want to select zones 2, 5, and 6, enter:
[2 5 8 0 4][AWAY][2][STAY][5][STAY][6][STAY]
[AWAY]
System Functions
35