Marker Disassembly / Assembly - Tippmann ALPHA BLACK MARKER LINE Owner's Manual

Storage (continued from page 15) Storage (continued from page 15)
your marker with the bolt in the forward position, uncocked. your marker with the bolt in the forward position, uncocked.
When removing your marker out of storage make sure Barrel Sleeve is When removing your marker out of storage make sure Barrel Sleeve is
E E
installed (see page 2) and safety is in Safe Mode (see page 4). You installed (see page 2) and safety is in Safe Mode (see page 4). You
N N
should re-oil the rear bolt and the front bolt o-ring before use (see should re-oil the rear bolt and the front bolt o-ring before use (see
cleaning and maintenance on page 14). cleaning and maintenance on page 14).
G G
L L

Marker Disassembly / Assembly

Marker Disassembly / Assembly
I I
Eye protection must be worn during disassembly / assembly. Eye protection must be worn during disassembly / assembly.
First follow First follow Unloading Your Marker and Unloading Your Marker and
S S
instructions on page 14. Do not pressurize a instructions on page 14. Do not pressurize a
H H
partially assembled paintball marker. partially assembled paintball marker.
Put the marker into the uncocked position. Put the marker into the uncocked position.
To uncock the marker: Pull and hold the bolt To uncock the marker: Pull and hold the bolt
cocking handle cocking handle back back
trigger and release the handle slowly forward trigger and release the handle slowly forward
which will uncock the marker. which will uncock the marker.
NOTE: Carefully hand start NOTE: Carefully hand start
all threaded parts and do all threaded parts and do
not overtighten and strip not overtighten and strip
threaded parts threaded parts
when assembling. when assembling.
TA06200 TA06200
Tactical Tactical
Shroud Shroud
Edition parts Edition parts
Not Shown Not Shown
In Basic In Basic
schematics schematics
parts (on parts (on
pages pages
TA09919 TA09919
12-13). 12-13).
Bolt Bolt
TA06201 TA06201
Collapsible Stock Assembly Collapsible Stock Assembly
(Replaces End Cap Cover ) (Replaces End Cap Cover )
Remove the barrel Remove the barrel unscrew unscrew
press the 2 tabs press the 2 tabs in and slide it out. in and slide it out.
until it stops. until it stops. Loosen the 2 adapter bolts Loosen the 2 adapter bolts
elbow elbow , press the feed lock , press the feed lock
the receiver. the receiver.
To remove the left-side receiver To remove the left-side receiver
connection bolts ( 3 long - connection bolts ( 3 long -
side receiver to access the internal parts. side receiver to access the internal parts.
Air Supply Cylinder Removal Air Supply Cylinder Removal
- then pull the - then pull the
Power Power
Button Button
LED LED
On On
E-Trigger E-Trigger
Markers Markers
NOTE: (if 2 adapter bolts NOTE: (if 2 adapter bolts
removed, the short bolt goes in front removed, the short bolt goes in front
when reassembling). when reassembling).
. . Remove the magazine Remove the magazine
Turn the velocity screw Turn the velocity screw
. . Remove the feed Remove the feed
, tilt the feed elbow out and slide it off , tilt the feed elbow out and slide it off
, unscrew , unscrew the 7 receiver the 7 receiver
) + (4 short - ) + (4 short - ). Then carefully lift the left- ). Then carefully lift the left-
16 16
Marker Disassembly (continued on page 17) Marker Disassembly (continued on page 17)
Marker Disassembly (continued from page 16) Marker Disassembly (continued from page 16)
With left half removed, pull the end cap out to remove the guide pin With left half removed, pull the end cap out to remove the guide pin
and drive spring (these parts must be removed before the bolt handle and drive spring (these parts must be removed before the bolt handle
can be removed). Disconnect the linkage arm from the rear and front can be removed). Disconnect the linkage arm from the rear and front
bolts. Slide the front bolt off the power tube and check the o-ring. Clean bolts. Slide the front bolt off the power tube and check the o-ring. Clean
and oil the o-ring or if damaged, replace with a new one. Do the same and oil the o-ring or if damaged, replace with a new one. Do the same
with the rear bolt o-ring. with the rear bolt o-ring.
Power tube and valve removal. Power tube and valve removal.
NOTE: Do not remove the gas line fitting unless it is leaking or you need NOTE: Do not remove the gas line fitting unless it is leaking or you need
to replace the valve. If you should do so you will need some teflon tape to replace the valve. If you should do so you will need some teflon tape
or paste to reinstall it. Carefully hand start all threaded parts and do not or paste to reinstall it. Carefully hand start all threaded parts and do not
overtighten and strip threaded parts when assembling. overtighten and strip threaded parts when assembling.
First, complete Marker Disassembly Instructions (see page 16). First, complete Marker Disassembly Instructions (see page 16).
Power tube removal: To remove the power tube Power tube removal: To remove the power tube
and valve, unscrew and valve, unscrew
bolts bolts from the right side receiver. from the right side receiver.
Valve removal from power tube: If it is necessary to remove the valve, Valve removal from power tube: If it is necessary to remove the valve,
use a wrench ( use a wrench (
fitting is out, the valve will slide out the back of the power tube. fitting is out, the valve will slide out the back of the power tube.
NOTE:
NOTE: Check the external valve o-ring and if damaged, replace with Check the external valve o-ring and if damaged, replace with
a new one. If the o-ring is damaged your marker will not function a new one. If the o-ring is damaged your marker will not function
correctly. correctly.
Reinstall the valve: Insert cleaned and oiled valve into the power tube Reinstall the valve: Insert cleaned and oiled valve into the power tube
and align the holes of the valve and power tube. and align the holes of the valve and power tube.
paste on threads of gas line fitting and carefully screw it into the valve paste on threads of gas line fitting and carefully screw it into the valve
and snug with a wrench ( and snug with a wrench (
parts). parts). Wipe off any excess paste. Wipe off any excess paste.
Reinstall the power tube/valve into receiver: Apply red loctite #271 Reinstall the power tube/valve into receiver: Apply red loctite #271
sealant to threads of two valve lock bolts and attach sealant to threads of two valve lock bolts and attach
over tighten bolts and strip threads. over tighten bolts and strip threads.
are are
, ,
in in
the two valve lock the two valve lock
) to slowly unscrew the gas line fitting. Once the ) to slowly unscrew the gas line fitting. Once the
Clean all parts and oil the o-rings. Clean all parts and oil the o-rings.
)(do not over tighten and strip threaded
)(do not over tighten and strip threaded
Wipe off any excess paste. Wipe off any excess paste.
17 17 Marker Disassembly / Assembly
E E
N N
G G
L L
I I
S S
H H
Apply teflon tape or Apply teflon tape or
- do not - do not
Marker Disassembly / Assembly
(continued on page 18) (continued on page 18)