Tippmann ALPHA BLACK MARKER LINE Owner's Manual page 11

Marker Disassembly / Assembly (continued from page 17) Marker Disassembly / Assembly (continued from page 17)
Reassembling Receiver Halves: Reassembling Receiver Halves:
STEP 1: STEP 1: Double check that the Trigger Assembly Double check that the Trigger Assembly
E E
; and other parts: Feed Elbow Lock ; and other parts: Feed Elbow Lock
N N
Ball Latch Ball Latch ; Front Bolt* ; Front Bolt*
; Rear Bolt* ; Rear Bolt* + Bolt Insert + Bolt Insert
G G
Guide Pin* Guide Pin* ; Buffer O-ring ; Buffer O-ring
L L
Tank Adapter Nuts Tank Adapter Nuts ; are in place and (*=oiled) (see below and ; are in place and (*=oiled) (see below and
I I
schematics on pages 11–12 for details as needed). schematics on pages 11–12 for details as needed).
Non-E-Trigger Non-E-Trigger Markers go to STEP 2) on page 19. Markers go to STEP 2) on page 19.
TM TM
S S
H H
For E-Trigger For E-Trigger Markers: Markers:
TM TM
Do not operate sear tripper assembly uninstalled as solenoid / Do not operate sear tripper assembly uninstalled as solenoid /
armature may pinch you. armature may pinch you.
Double check that the E-Trigger Double check that the E-Trigger
are Positioned correctly for Reassembly are Positioned correctly for Reassembly
as follows: as follows:
1) Place solenoid / (armature - fits 1) Place solenoid / (armature - fits
inside solenoid) into right receiver. inside solenoid) into right receiver.
2) Carefully align and insert the 2) Carefully align and insert the
electronics board electronics board into slot. into slot.
3) Place trigger switch on two pins 3) Place trigger switch on two pins
of right receiver half. of right receiver half.
4) Insert capacitor in slot. 4) Insert capacitor in slot.
5) Route wires in cutout areas to lay flat under armature pin and 5) Route wires in cutout areas to lay flat under armature pin and
battery and not be pinched when receiver halves are reassembled. battery and not be pinched when receiver halves are reassembled.
Visually inspect internal wires for disconnected wire end(s) or Visually inspect internal wires for disconnected wire end(s) or
damage. damage.
6) Insert armature pin 6) Insert armature pin
7) Insert Magnet 7) Insert Magnet in slot below armature as shown. in slot below armature as shown.
Double check that all parts are in place as shown. Double check that all parts are in place as shown.
Place battery connector Place battery connector
sure the magnet fits into left receiver half slot so it does not break sure the magnet fits into left receiver half slot so it does not break
and and wires are not pinched as you wires are not pinched as you
the halves fit flush. the halves fit flush.
(E-Trigger (E-Trigger Markers Go to STEP 2 on page 19). Markers Go to STEP 2 on page 19).
TM TM
+ Pin + Pin + Spring + Spring
; Linkage Arm* ; Linkage Arm* ; Link Arm Pins (2) ; Link Arm Pins (2)
; Bolt Handle ; Bolt Handle ; Drive Spring* ; Drive Spring*
; End Cap ; End Cap + End Cap Cover + End Cap Cover
E-Trigger E-Trigger Parts Not Shown Parts Not Shown
TM TM
in Basic Parts List on in Basic Parts List on
Parts Parts
TM TM
(pages 12-13) (pages 12-13)
TA01135 Sear TA01135 Sear
02-88 02-88
Sear Spring Sear Spring
TA06020 Armature Pin TA06020 Armature Pin
TA09935 TA09935
Electronics Electronics
Assembly Assembly
Solenoid Solenoid
-Armature -Armature
TA05014 Magnet TA05014 Magnet
into 2 slots so it moves freely. into 2 slots so it moves freely.
through left receiver half through left receiver half
place left half on right half so place left half on right half so
18 18 Reassembling Receiver Halves: Reassembling Receiver Halves:
(continued on page 19) (continued on page 19)
Reassembling Receiver Halves: (continued from page 18) Reassembling Receiver Halves: (continued from page 18)
; ;
+ +
; 2 ; 2
Carefully hand start Carefully hand start
all threaded parts and all threaded parts and
do not overtighten and strip threaded parts when assembling. do not overtighten and strip threaded parts when assembling.
STEP 2: STEP 2:
Carefully install the left receiver half (make sure halves fit flush). Carefully install the left receiver half (make sure halves fit flush).
Insert 4 short receiver bolts Insert 4 short receiver bolts
If marker has a barrel shroud If marker has a barrel shroud
Insert 3 long receiver bolts Insert 3 long receiver bolts
Attach adapter Attach adapter
bolt goes in front). bolt goes in front).
the barrel the barrel and carefully and carefully
Slide the feed elbow Slide the feed elbow
holds it in place. holds it in place.
E-Trigger E-Trigger
TM TM
battery connector and be sure the wires lay flat inside battery connector and be sure the wires lay flat inside
the cutout area of the receiver. the cutout area of the receiver.
Carefully tilt and insert the battery (wire attached Carefully tilt and insert the battery (wire attached
make make
end first end first ) into the receiver. ) into the receiver.
Install the left receiver grip Install the left receiver grip
Press in the 2 magazine tabs Press in the 2 magazine tabs
magazine magazine
lock it in place. NOTE: The magazine may be used lock it in place. NOTE: The magazine may be used
to store tools and lubricating oil for your marker to store tools and lubricating oil for your marker
(shown with 2 allen wrenches (shown with 2 allen wrenches
. .
- insert it now. - insert it now.
and and Tighten Tighten
tighten tighten 2 bolts 2 bolts
Apply marker oil onto the barrel o-ring, insert Apply marker oil onto the barrel o-ring, insert
screw it in. screw it in.
into the receiver and tilt up until the feed lock into the receiver and tilt up until the feed lock
Markers - Attach a 9 volt battery to the Markers - Attach a 9 volt battery to the
with 2 bolts with 2 bolts
and slide the and slide the
up into the marker until the tabs up into the marker until the tabs
and oil). and oil).
19 19
E E
N N
G G
L L
I I
S S
H H
the 7 bolts the 7 bolts / / . .
(NOTE: short adapter (NOTE: short adapter
. .