Ricoh DDP92 Maintenance Manual page 54

Detail
Error Error Name
Code
E1D1 FNS LEAD JAM 2
E1D2 FNS LEAD JAM 3
E1D3 FNS LEAD JAM 4
E1D5 FNS TRAIL JAM 2
E1D6 FNS TRAIL JAM 3
E1D7 FNS TRAIL JAM 4
E1D8 FNS LEAD JAM 5
E1D9 FNS TRAIL JAM 5
E255 INSERTER PICK COUNT OVER
E259 CONFIGURATION ERROR
E260 FINISHER CPU ERROR
E262 FINISHER INCORRECT
COMMAND
E264 FINISHER ACT TIMEOUT
E266 FINISHER DORMANT TIMEOUT
E268 FINISHER BUSY TIMEOUT
E26A FINISHER ST EXIT SIGNAL
ERROR
E26C FINISHER PRINT TIMEOUT
E2B1 FNS COVER SHEET TRAY
TIMEOUT
E2C1 STAPLER POSITION ERROR
E2C2 STAPLING ERROR
E2C3 STAPLING F ERROR
E2C4 STAPLING R ERROR
E2C5 STAPLER ROTATE ERROR 1
E2C6 SHIFT TRAY TIMEOUT
E2C7 ALIGNMENT PLATE POSITION
ERROR
E2C8 SHIFT POSITION ERROR
E2C9 BELT POSITION ERROR
E2CA PAPER EXIT OPENING
POSITION ERROR
E2CB STAPLER ROTATE ERROR 2
E2E5 FNS DRIVER
E2E7 FNS CONVEYANCE MOTOR
ERROR
E2E8 FOLDING CONVEYANCE MOTOR
ERROR
Paper did not arrive at Paper Exit 2 PS.
Paper did not arrive at Stacker Conveyance Passage PS.
Paper did not arrive at Paper Exit 1 PS.
Paper did not depart from Paper Exit 2 PS.
Paper did not depart from Stacker Conveyance Passage PS.
Paper did not depart from Paper Exit 1 PS.
Paper did not arrive at Sub-Tray Paper Exit PS.
Paper did not depart from Sub-Tray Paper Exit PS.
The insert pick count is over 15 sheets.
Finisher configuration is changed.
Slave processor cannot receive the status data from the
Finisher processor.
Finisher received the command when its condition prohibits
PR from issuing.
Finisher does not become an activate condition.
Finisher does not become a dormant condition.
The Busy signal of the Finisher is on more than specified time.
The Stacker exit signal is on more than specified time.
The Print signal of the Finisher is on more than specified time.
The table of the Cover Sheet Feeder is on more than the
specified time.
Abnormality was detected in the Staple Movement HP PS.
Both staplers missed to staple.
Stapler (Front) missed to staple.
Stapler (Rear) missed to staple.
Abnormality was detected in the Staple Rotation HP PS.
(slant)
The Main Tray was driven too long time.
Abnormality was detected in the Alignment Plate/Upper HP
PS.
Abnormality was detected in the Roller Shift HP PS.
Abnormality was detected in the Paper Exit Belt HP PS.
Abnormality was detected in the Paper Exit Opening PS.
Abnormality was detected in the Stapler Rotation HP PS.
(parallel)
Abnormality was detected in the Finisher driver.
FNS Conveyance Motor did not work correctly.
Folding Conveyance Motor did not work correctly.
M M L 0 0
Description
Troubleshooting
Page
No.
5-22
5-22
5-22
5-22
5-22
5-22
5-22
5-22
5-26
5-43
5-26
5-27
5-27
5-27
5-27
5-27
5-27
5-28
5-29
5-30
5-30
5-30
5-31
5-32
5-33
5-34
5-35
5-36
5-36
5-37
5-37
5-37
5-9