Page 1 V09.1.00...
Page 3 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Page 4: Fcc Statement
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 5: Fcc Rf Radiation Exposure Statement
Preface FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Page 6: Important Safety Instructions
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Page 7: Instructions For Care And Operation
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Page 8 Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.
Page 9: Power Safety
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a Power Safety steady, uninterrupted power supply. If you are unsure of your local power specifications, Warning consult your service representative or local power company.
Page 10: Battery Precautions
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Page 11: Cleaning
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.
Page 12: Travel Considerations
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
Page 13 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
Page 14 Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
Page 15: Lcd Screen Care
Preface Lighting Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...
Page 16 Preface...
Page 17: Table Of Contents
Preface Contents Notice .................I Touch Sensor Instant Keys ..........1-8 FCC Statement ..............II Keyboard ................1-9 FCC RF Radiation Exposure Statement: ......III Function Keys & Visual Indicators ......1-10 EuP Off Mode Power Consumption Statement: ..... III System Map: Front & Rear Views .......1-11 Instructions for Care and Operation ........
Page 18 Preface GameMate Media Player (HDMI-In) ......2-10 Sleep ................3-6 HDMI Audio Configuration ........2-13 Hibernate ................3-7 Audio Setup for LCD Monitors/ Shut down ..............3-7 TVs with HDMI Input ..........2-14 Configuring the Power Buttons ........3-8 Audio Features .............2-16 Resuming Operation ............3-9 Suppressing Audio Background Noise ......2-17 Battery Information ............3-10 Setup for Audio Recording ..........2-19 Conserving Battery Power ...........3-11...
Page 19 Preface Audio ................4-5 BIOS Revision/VGA Card etc. (Main Menu) ....5-7 LAN ................4-5 Advanced Menu .............5-8 TouchPad ...............4-6 SATA Mode (Advanced Menu) ........5-8 Card Reader/ExpressCard ..........4-6 Legacy USB Support: (Advanced Menu) ......5-9 GameKey Utility ............4-6 Boot-time Diagnostic Screen: (Advanced Menu) ..5-9 Hot Key ................4-6 Power On Boot Beep (Advanced Menu) .......5-9 HDMI-In Driver .............4-6...
Page 20 Preface Modules Remote Control Unit ............7-31 Fingerprint Reader Module ..........7-32 Overview ................7-1 Fingerprint Reader Driver Installation ......7-33 Setting Up SATA RAID Mode ........7-2 User Enrollment ............7-34 Intel® Matrix Storage Manager ........7-2 Fingerprint Control Center Features ......7-37 SATA RAID Setup Procedure (BIOS) ......7-4 RAID Setup (Intel Matrix) ..........7-5 Troubleshooting Intel®...
Page 21 Preface HDMI-IN Port .............. A-3 Video Adapter Options ..........C-2 Headphone-Out Jack ............. A-3 BIOS ................C-2 Line-In Jack ..............A-3 Storage ................C-2 Microphone-In Jack ............A-4 Audio ................C-2 Mini-IEEE 1394 Port ............ A-4 Keyboard & Pointing Device ........C-3 RJ-45 LAN Jack ............
Page 22 Preface...
Page 23: Quick Start Guide
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
Page 24: Advanced Users
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - “BIOS Utilities” on page 5 - 1 “Upgrading The Computer”...
Page 25: Not Included
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers.
Page 26: System Software
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, TV Tuner Module Support you will find the Windows 7 operating system is supported. Note that the TV Tuner Note: In order to run Windows 7 without limitations or decreased performance, your module (factory) option...
Page 27: System Startup
Quick Start Guide System Startup 1. Remove all packing materials, and place the computer on a stable surface. 2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. 3. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Page 28: System Map: Lcd Panel Open & Top View
Quick Start Guide System Map: LCD Panel Open & Top View Figure 1 - 2 LCD Panel Open & Top View Wireless Device 1. Optional Built-In PC Operation Aboard Camera Aircraft 2. LCD 3. LED Status Indicators The use of any portable elec- 4.
Page 29: Led Indicators
Quick Start Guide LED Indicators Game Keys The two sets of LED indicators (LED Status Indica- The eight Game Keys on the left of the computer al- tors and LED Power Indicators) display helpful in- low macros to be configured for common keystrokes formation about the current status of the computer.
Page 30: Touch Sensor Instant Keys
Quick Start Guide Touch Sensor Instant Keys Press the Touch Sensor Instant Keys on the computer to toggle the appropriate function on/off. When a module is powered on the appropriate icon will be highlighted. Icon Description Icon Description LED Color Toggle (press to toggle Wireless LAN Module Power Toggle flashing colors or single color) PC Camera Module Power Toggle...
Page 31: Keyboard
Quick Start Guide Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and Other Keyboards features function keys to allow you to change operational features instantly. See Table 1 - 3, on page 1 - 10 for full function key combination details.
Page 32: Function Keys & Visual Indicators
Quick Start Guide Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators (see the table below) are available when the Hot Key driver is in- 6).
Page 33: System Map: Front & Rear Views
Quick Start Guide System Map: Front & Rear Views Figure 1 - 5 Front View 1. Color LEDs 2. Speakers 3. LED Power Indicators 4. Consumer Infrared Transceiver (enabled with optional TV Tuner only) 5. DC-In Jack Appendix A for a more TV Tuner Module Support detailed description of the ports &...
Page 34: System Map: Right View
Quick Start Guide System Map: Right View Figure 1 - 6 Right View 1. Headphone-In Jack 2. Microphone-In Jack 3. Line-In Jack 4. S/PDIF-Out Jack 5. Cable (CATV) Antenna Jack 6. Combined eSATA/ USB Port TV Tuner Module Support 7. USB 2.0 Port 8.
Page 35: System Map: Left View
Quick Start Guide System Map: Left View Figure 1 - 7 Left View 1. DVI-Out Port 2. 2 * USB 2.0 Ports 3. RJ-45 LAN Jack 4. HDMI-Out Port 5. 7-in-1 Card Reader 6. ExpressCard 34 Slot 7. HDMI-In Port 8.
Page 36 Quick Start Guide Changing DVD Regional Codes Disk Eject Warning Go to the Control Panel and double-click Device Don’t try to eject a CD/DVD while the system is ac- Manager (Hardware and Sound), then click the + cessing it. This may cause the system to “crash”. Stop next to DVD/CD-ROM drives.
Page 37: System Map: Bottom View
Quick Start Guide System Map: Bottom View Figure 1 - 8 Bottom View 1. Sub Woofer 2. Fan Outlet/Intake 3. Component Bay Cover 4. Battery (Secondary HDD Bay - HDD3) 5. Primary HDD Bay (HDD1 & 2) Appendix A for a more detailed description of the ports &...
Page 38 Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are ac- cessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Page 39: Video Features
Quick Start Guide Video Features You can configure display options, from the Display Settings control panel in Windows as long as the appro- priate video driver is installed. For more detailed video information see “NVIDIA Video Driver Controls” on page B - To access Display (Control Panel) and Screen Resolution in Windows: Click Start and click Control Panel.
Page 40 Quick Start Guide Screen Resolution Video Options Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest de- tails on video cards supported. Figure 1 - 10 - Screen Resolution 1 - 18 Video Features...
Page 41 Quick Start Guide NVIDIA Control Panel Figure 1 - 11 - NVIDIA Control Panel Video Features 1 - 19...
Page 42: Power Options
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 16) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu.
Page 43: Storage Devices, Mouse, Audio & Printer
Storage Devices, Mouse, Audio & Printer Chapter 2: Storage Devices, Mouse, Audio & Printer Overview Read this chapter to learn more about the following main features and components of the computer: • Hard Disk Drive • Optical Device • 7-in-1 Card Reader •...
Page 44: Hard Disk Drive
Storage Devices, Mouse, Audio & Printer Hard Disk Drive The hard disk drive(s) is(are) used to store your data in the computer. The hard Power Safety disk(s) can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
Page 45: Optical Device
Storage Devices, Mouse, Audio & Printer Optical Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de- Sound Volume vice will depend on the model you purchased (see “Storage” on page C - 2). The Adjustment optical device is usually labeled “Drive D:”...
Page 46: Handling Cds Or Dvds
Storage Devices, Mouse, Audio & Printer Handling CDs or DVDs Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be CD Emergency Eject accessed.
Page 47: Dvd Regional Codes
Storage Devices, Mouse, Audio & Printer DVD Regional Codes To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - DVD Regional Coding Table 2 - 1 Region Geographical Location DVD Regional Coding USA, Canada Western Europe, Japan, South Africa, Middle East &...
Page 48: 7-In-1 Card Reader
Storage Devices, Mouse, Audio & Printer 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the Card Reader Cover card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Page 49: Expresscard Slot
Storage Devices, Mouse, Audio & Printer ExpressCard Slot The computer is equipped with an ExpressCard/34 slot that reads Express Card/34 ExpressCard and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Slot Cover Cards).Make sure you install the ExpressCard driver (see “Card Reader/Express- Card”...
Page 50: Game Keys
Storage Devices, Mouse, Audio & Printer Game Keys The eight game hot keys on the left of the computer allow macros to be configured for common keystrokes used in applications (the keys can assigned macros for any program, not only games). To configure the keys follow the instructions below (make sure you have installed the GameKey Utility driver - see “GameKey Utility”...
Page 51: Hdmi Ports
Storage Devices, Mouse, Audio & Printer HDMI Ports This computer features both HDMI (High-Definition Multimedia Interface) input and output ports. HDMI is a compact audio/video interface for transmitting uncom- pressed digital data. • The HDMI-Out port allows you to display and hear video/audio sources from your computer to digital TVs, displays or audio systems that support an HDMI input.
Page 52: Gamemate Media Player (Hdmi-In)
Storage Devices, Mouse, Audio & Printer GameMate Media Player (HDMI-In) The GameMate Media Player allows you to play content from digital sources through the HDMI-In port. Connect your digital source to the HDMI-In port using an HDMI cable. Access the GameMate Media Player from the desktop shortcut or from GameMate folder in Program Files.
Page 53 Storage Devices, Mouse, Audio & Printer Double-click the GameMate screen to toggle through different screen size options. You can also right-click the screen to access the configuration menu to adjust any of the following settings: RENDERED QUALITY Select High, Medium or Low quality from this menu item. STANDARD Select NTSC or PAL standard from this item.
Page 54 Storage Devices, Mouse, Audio & Printer ASPECT The Aspect item allows you to select standard or wide screen aspect ratios. SNAPSHOT Click either the BMP or JPG items to take a screen shot of the current GameMate screen (the file will be placed in the Pictures library folder in Windows). TOPSHOT If enabled then the GameMate screen will remain on top of other windows.
Page 55: Hdmi Audio Configuration
Storage Devices, Mouse, Audio & Printer HDMI Audio Configuration As HDMI (High-Definition Multimedia Interface) carries both audio and video sig- nals you can configure the audio output as per the instructions below. Audio Setup for HDMI Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound).
Page 56: Audio Setup For Lcd Monitors/Tvs With Hdmi Input
Storage Devices, Mouse, Audio & Printer Audio Setup for LCD Monitors/TVs with HDMI Input Some LCD monitors/TVs support HDMI input, but DO NOT have built-in digital audio decoders. Where this is the case, when playing DVDs in Windows Media Player/CyberLink Power DVD, a background noise can occur. If this situation does arise then please follow the instructions below.
Page 57 Storage Devices, Mouse, Audio & Printer HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempt- ing to play audio/video sources through the device. Other Applications • If you disconnect the HDMI cable the default audio playback device will not If you are using a third revert to speakers until the computer is restarted (if you do not wish to restart the party application to play...
Page 58: Audio Features
Storage Devices, Mouse, Audio & Printer Audio Features You can configure the audio options on your computer from the Sound control Sound Volume panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ Adjustment control panel (right-click the taskbar icon to bring up an audio menu).
Page 59: Suppressing Audio Background Noise
Storage Devices, Mouse, Audio & Printer Suppressing Audio Background Noise A background noise may occur when audio power management is enabled, and the system resumes from power saving. To solve this problem you can disable Realtek HD Audio Manager Power Management. Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View.
Page 60 Storage Devices, Mouse, Audio & Printer Make sure that Power Management is disabled (when disabled the icon will be black ; when enabled the icon will be blue Click OK to save the setting and close the control panel. The black icon indicates that Power Management is disabled.
Page 61: Setup For Audio Recording
Storage Devices, Mouse, Audio & Printer Setup for Audio Recording To record audio sources on your computer at optimum quality follow the instruc- tions below: Beam Forming Click Start, and click Control Panel (or point to Settings and click Control Panel) If your stereo micro- and make sure you are in Classic View.
Page 62: Setup For 5.1 Surround Sound
Storage Devices, Mouse, Audio & Printer Setup for 5.1 Surround Sound To setup your system for 5.1 surround sound you will need to connect the audio ca- bles to the Line-In and Microphone-In jacks. Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View.
Page 63 Storage Devices, Mouse, Audio & Printer Plug the front speaker cables into the Headphone-Out Jack. Plug in the other cables (you may require an adapter to connect each cable to the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as follows: •...
Page 64: Sound Effects Equalizer
Storage Devices, Mouse, Audio & Printer Sound Effects Equalizer Press the Sound Effects Equalizer Mode Toggle button to toggle through some of the equalizer options (an on-screen icon will appear to show the selected mode). A more comprehensive list of options is available from the Equalizer drop- down list.
Page 65: Dolby Settings
Storage Devices, Mouse, Audio & Printer Dolby Settings You can adjust the Dolby settings from the Dolby tab in Speakers Properties. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Playback (tab).
Page 66: Touchpad And Buttons/Mouse
Storage Devices, Mouse, Audio & Printer TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to Mouse Driver your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Page 67: Gestures And Device Settings
Storage Devices, Mouse, Audio & Printer Gestures and Device Settings The Synaptics Gestures Suite application allows you to use a specific gesture (ac- tion) on the surface of the TouchPad to perform specific actions to manipulate doc- Show Video uments, objects and applications. You can get a clearer view of the gestures in- volved by clicking the...
Page 68 Storage Devices, Mouse, Audio & Printer Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight con- tinuous motion).
Page 69 Storage Devices, Mouse, Audio & Printer Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Page 70: Adding A Printer
Storage Devices, Mouse, Audio & Printer Adding a Printer The most commonly used peripheral is a printer. The following conventions will Parallel Printer help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options.
Page 71: Power Management
Power Management Chapter 3: Power Management Overview OS Note Power management To conserve power, especially when using the battery, your computer power man- functions will vary slight- agement conserves power by controlling individual components of the computer ly depending on your (the monitor and hard disk drive) or the whole system.
Page 72: The Power Sources
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components (see page Attach the AC/DC adapter to the DC-In jack at the rear of the computer.
Page 73: Turning On The Computer
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the pow- Forced Off er button on the front panel. If the system “hangs”, When the computer is on, you can use the power button as a Stand by/Hibernate/ and the Ctrl + Alt + Del Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and key combination doesn’t...
Page 74: Power Plans
Power Management Power Plans The computer can be configured to conserve power by means of power plans. You Resuming can use (or modify) an existing power plan, or create a new one. Operation The settings may be adjusted to set the display to turn off after a specified time, and Table 3 - 1, on to send the computer into Sleep after a period of inactivity.
Page 75 Power Management Each Windows power plan will also adjust the processor performance of your ma- chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is pow- ered from an AC power source.
Page 76: Power-Saving States
Power Management Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps.
Page 77: Hibernate
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a Silent Mode power failure occurs the system can restore your work from the hard disk; if a power You can use Silent failure occurs when work is saved only to memory, then the work will be lost.
Page 78: Configuring The Power Buttons
Power Management Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the Password computer in to a power-saving state. Click Choose what the power buttons do on Protection the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to...
Page 79: Resuming Operation
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Closing the Lid If you have chosen to Power Status Icon Color To Resume send the computer to...
Page 80: Battery Information
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Battery Power Warning Your computer’s battery power is dependent upon many factors, including the pro- When the battery is criti- grams you are running, and peripheral devices attached. You can set actions to be cally low, immediately connect AC/DC...
Page 81: Conserving Battery Power
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. Windows Mobility Center • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.
Page 82: Battery Life
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to re- move the battery for any reason (e.g.
Page 83: Proper Handling Of The Battery Pack
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances. • DO NOT expose the battery to fire or high temperatures, it may explode. Caution • DO NOT connect the metal terminals (+, -) to each other. Danger of explosion if battery is incorrectly re- placed.
Page 84: Battery Faq
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Page 85 Power Management Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings. Figure 3 - 8 Change Plan Settings / Change Advanced Power Settings Battery Information 3 - 15...
Page 86 Power Management Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears): Figure 3 - 9 Power Options Advanced Settings - Battery • Low battery levels = 0% •...
Page 87 Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Page 88 Power Management 3 - 18...
Page 89: Drivers & Utilities
Drivers & Utilities Chapter 4: Drivers & Utilities What to Install This chapter deals with installing the drivers and utili- ties essential to the operation or improvement of some The Device Drivers & Utilities + User’s Manual disc of the computer’s subsystems. The system takes ad- contains the drivers and utilities necessary for the vantage of some newer hardware components for proper operation of the computer.
Page 90: Driver Installation
Drivers & Utilities Driver Installation Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in Insert the Device Drivers & Utilities + User’s Manual this order) which is the same as that listed in the disc and click Install Drivers (button), or Option Driv- Drivers Installer menu below.
Page 91: Manual Driver Installation
Drivers & Utilities Manual Driver Installation Windows 7 Driver Page Click the Browse CD/DVD button in the Drivers In- staller application and browse to the executable file in Video Page 4 - 5 the appropriate driver folder. Audio Page 4 - 5 Windows Update Page 4 - 5 After installing all the drivers make sure you enable...
Page 92: Updating/Reinstalling Individual Drivers
Drivers & Utilities Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it If a User Account Control prompt appears as part of may be necessary to uninstall the original driver.To do the driver installation procedure, click Continue/Al- this go to the Control Panel in the Windows OS and low, and follow the installation procedure as directed.
Page 93: Driver Installation Procedure
Drivers & Utilities Driver Installation Procedure Video Insert the Device Drivers & Utilities + User’s Manual 1. Click 1.Install Video Driver > Yes. disc and click Install Drivers (button), or Option Driv- 2. Click Next > Yes > Next. ers (button) to access the Optional driver menu. 3.
Page 94: Touchpad
Drivers & Utilities TouchPad Hot Key 1. Click 4.Install Touchpad Driver > Yes. 1. Click 7.Install Hotkey Driver > Yes. 2. Click Next > Next. 2. Click Next. 3. Click Finish > Finish to restart your computer. 3. Click the button to accept the license, and then click Next.
Page 95: Optional Drivers
Drivers & Utilities Optional Drivers See the pages indicated for the driver installation pro- cedures for any modules included in your purchase op- Windows Update tion. After installing all the drivers make sure you enable Win- dows Update in order to get all the latest security up- dates etc.
Page 96: Wireless Lan
Drivers & Utilities RAID Setup Consumer Infrared (for TV Tuner Remote) Note: Prior to setting up the RAID you will need to use See the install procedure in “TV Tuner Module” on an operable computer to copy the RAID driver to a page 7 - USB flash drive before installing the Windows Vista operating system.
Page 97: Bios Utilities
BIOS Utilities Chapter 5: BIOS Utilities Overview BIOS Screens Note that BIOS This chapter gives a brief introduction to the computer’s built-in software: screens pictured these pages are intend- Diagnostics: The POST (Power-On Self Test) ed for guidance in set- ting up your system’s BIOS.
Page 98: The Power-On Self Test (Post)
BIOS Utilities The Power-On Self Test (POST) If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you POST Screen turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). 1.BIOS information 2.CPU type As the POST proceeds, the computer will tell you if there is anything wrong.
Page 99: Failing The Post
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non- fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
Page 100: The Setup Utility
BIOS Utilities The Setup Utility The Phoenix Setup utility tells the system how to configure itself and manage basic BIOS Settings features and subsystems (e.g. port configuration). Warning Entering Setup Incorrect settings can cause your system to To enter Setup, turn on the computer and press F2 during the POST. The prompt malfunction.
Page 101: Setup Screens
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a Setup menus heading, a new screen appears. Scroll through the features listed on each screen to shown in this section are make changes to Setup.
Page 102: Main Menu
BIOS Utilities Main Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 2 Main M ai n Advanced Security Boot Exit Main Menu Item Specific Help System Time: [22:12:05] System Date: [11/23/2009] System Memory: 628 KB <Tab>, <Shift Tab>, or Extended Memory: 2039 MB <Enter>...
Page 103: System/Extended Memory: (Main Menu)
BIOS Utilities System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. BIOS Revision/VGA Card etc. (Main Menu) This item contains information on the BIOS version and video card etc., and is not user configurable.
Page 104: Advanced Menu
BIOS Utilities Advanced Menu Phoenix SecureCore(tm) Setup Utility SATA Mode Main A A dvanced Advanced Security Boot Exit Figure 5 - 3 Item Specific Help If you have installed the Advanced Menu Windows 7 operating Determines how SATA system with either AHCI SATA Mode [AHCI] controller(s) operate.
Page 105: Legacy Usb Support: (Advanced Menu)
BIOS Utilities Legacy USB Support: (Advanced Menu) Choose “Enabled” if you intend to use USB devices in systems which do not nor- mally support USB functionality (e.g. DOS). The default setting is “Enabled” and does not need to be changed if you intend to use your USB devices in Windows. Boot-time Diagnostic Screen: (Advanced Menu) Use this menu item to enable/disable the Boot-time Diagnostic Screen.
Page 106: Security Menu
BIOS Utilities Security Menu Phoenix SecureCore(tm) Setup Utility Security Menu Main Advanced Security S S e e c c u u r r i i t t y y Boot Exit Item Specific Help changes Supervisor Password Is: Clear make here affect the User Password Is: Clear Supervisor Password...
Page 107: Set User Password (Security Menu)
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the Phoenix SecureCore Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless Password Warning you choose to set a Password on Boot (see below). Many menu items in the Phoenix If you set a boot pass- SecureCore Setup Utility cannot be modified in user mode.
Page 108: Boot Menu
BIOS Utilities Boot Menu Phoenix SecureCore(tm) Setup Utility Main Advanced Security Boot Exit Figure 5 - 5 Boot Menu Item Specific Help Boot priority order: IDE CD: HL-DT-STDVDRAM GT30N-(S2) Keys used to view or IDE HDD: FUJITSU MHY2120BH-(S3) configure devices: PCI SCSI: Up and Down arrows USB HDD:...
Page 109: Exit Menu
BIOS Utilities Exit Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 6 Main Advanced Security Boot Exit Exit Menu Item Specific Help Exit Saving Changes Exit Discarding Changes Exit System Setup and Load Setup Defaults save your changes to CMOS. Discard Changes Save Changes Help...
Page 110 BIOS Utilities 5 - 14...
Page 111: Upgrading The Computer
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps out- Warranty Warning lined to make the desired upgrades. If you have any trouble or problems you can con- tact your service representative for further help. Before you begin you will need: Please check with your service representative...
Page 112: When Not To Upgrade
Upgrading The Computer When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replac- ing parts.You should not perform any of these upgrades if: Power Safety Warning Before you undertake • Your system is still under warranty or a service contract upgrade proce- •...
Page 113: Removing The Battery
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons Warranty Warning it is best to remove the battery. Please check with your Turn the computer off and turn it over. service representative Loosen screws and carefully lift the battery...
Page 114: Upgrading The Hard Disk Drive(S)
Upgrading The Computer Upgrading the Hard Disk Drive(s) The hard disk drive(s) can be taken out to accommodate other 2.5" serial (SATA) HDD System Warning hard disk drives with a height of 9.5mm (h) (see “Storage” on page C - 2).
Page 115 Upgrading The Computer Remove the hard disk bay cover Remove screws from the hard disk assembly. Remove the hard disk assembly by pulling the tab to disconnect it from the connector Figure 6 - 3 Bay Cover Removal & Hard Disk Assembly Screws Upgrading the Hard Disk Drive(s) 6 - 5...
Page 116 Upgrading The Computer Remove screws (depending on how many hard disks you have installed in the assembly). Separate the hard disk board from the case Separate the hard disk(s) & from the case. Reverse the process to install any new hard disk(s). Figure 6 - 4 Hard Disk(s) Removal...
Page 117 Upgrading The Computer Removing the Hard Disk in the Secondary HDD Bay Turn off the computer, and turn it over and remove the battery. The secondary hard disk bay is located under the battery compartment. Remove screws Slide the hard disk assembly in the direction of the arrow Lift the hard disk assembly out of the compartment.
Page 118: Upgrading The System Memory (Ram) - 1
Upgrading The Computer Upgrading the System Memory (RAM) - 1 The computer has two memory sockets for 204 pin Small Outline Dual In-line (SO- DIMM) DDR III (DDR3) type memory modules (see “Memory” on page C - The total memory size is automatically detected by the POST routine once you turn on your computer.
Page 119 Upgrading The Computer Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable , and remove the cover Figure 6 - 7 Component Bay Cover Removal Loosen the heat sink screws in the order indicated Figure 6 - 8 Heat Sink Screws...
Page 120 Upgrading The Computer Carefully (it may be hot) remove the heat sink Figure 6 - 9 Heat Sink Removal Contact Warning Be careful not to touch the metal pins on the module’s connecting Gently pull the two release latches ( &...
Page 121 Upgrading The Computer Pull the latches to release the second module if necessary. 10. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket. 11. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket as it will go.
Page 122 Upgrading The Computer 14. Replace the component bay cover and make sure you reconnect the fan cable (see Figure 6 - 7 on page 6 - 15. Replace all the component bay cover screws. 16. Restart the computer to allow the BIOS to register the new memory configuration as it starts up.
Page 123: Upgrading The System Memory (Ram) - 2
Upgrading The Computer Upgrading the System Memory (RAM) - 2 The computer has two memory sockets for 204 pin Small Outline Dual In-line (SO- DIMM) DDR III (DDR3) type memory modules (see “Memory” on page C - The total memory size is automatically detected by the POST routine once you turn on your computer.
Page 124 Upgrading The Computer Turn the computer over, open the Lid/LCD, and carefully (a cable is connected to the underside of the LED cover module) unsnap up the LED cover module from point on the right. Figure 6 - 13 LED Cover Module Removal Lift up the LED cover module and disconnect cable...
Page 125 Upgrading The Computer Remove screws from the keyboard. Figure 6 - 15 Keyboard Screws Carefully lift the keyboard up, being careful not to bend the keyboard ribbon cable. Disconnect the keyboard ribbon cable from the locking collar socket Figure 6 - 16 Disconnect the Keyboard Locking Collar...
Page 126 Upgrading The Computer Remove the keyboard Figure 6 - 17 Keyboard Removal Remove screws from the keyboard shielding plate Figure 6 - 18 Keyboard Shielding Plate Removal 6 - 16 Upgrading the System Memory (RAM) - 2...
Page 127 Upgrading The Computer 10. Gently pull the two release latches ( & on the sides of the memory socket in the direction indicated below. 11. The RAM module will pop-up, and you can remove it. Figure 6 - 19 RAM Module Removal Contact Warning Be careful not to touch...
Page 128 Upgrading The Computer 17. Snap the LED cover module down at the top of the module at points & 18. Push the LED cover module down on the left side at point , and then slide the module to the right (as illustrated) and snap down to secure it in place. Figure 6 - 20 LED Cover Module Slide to the Right &...
Page 129: Upgrading The Optical (Cd/Dvd) Device
Upgrading The Computer Upgrading the Optical (CD/DVD) Device Locate the hard disk bay cover and remove screws & Remove the hard disk bay cover Remove the screw at point , and use a screwdriver to carefully push out the optical device at point Reverse the process to install any new optical device.
Page 130: Upgrading The Video Card
Upgrading The Computer Upgrading the Video Card If you intend to upgrade or add another VGA card follow the procedures outlined Warranty Warning here. However please check with your service representative first to make sure your Please check with your computer can support more than one video card, and that you are not going to void service representative...
Page 131 Upgrading The Computer Remove screws (two video cards are pictured here) from the video card fan(s) and disconnect the fan cable(s) (if two cards are present). Remove the RAM fan(s) Figure 6 - 23 Video Card Fan Screws Caution The heat sink, and video card area in general, contains parts which are subject to high tempera-...
Page 132 Upgrading The Computer Remove screws from the heatsink in the order indicated on the label (two video cards are pictured here). Grip the handle and carefully remove the heatsink Caution Remove screws from the video card. The heat sink, and video card area in general, contains parts which are subject to high tempera-...
Page 133 Upgrading The Computer 10. Carefully remove the video card Caution The heat sink, and video card area in general, contains parts which are subject to high tempera- tures. Allow the area time to cool before re- moving these parts. Figure 6 - 26 Video Card Removal Upgrading the Video Card 6 - 23...
Page 134 Upgrading The Computer Installing a New Video Card Prepare to fit the video card into the slot by holding it at about a 30° angle. Contact Warning Be careful not to touch the metal pins on the VGA card’s connecting edge.
Page 135 Upgrading The Computer Fit the connectors firmly into the socket, straight and evenly. DO NOT attempt to push one end of the card in ahead of the other. Figure 6 - 28 Video Card Insertion Procedure The card’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket as it will go (none of the gold colored contact should be showing).
Page 136 Upgrading The Computer Secure the card with screws (Figure 6 - 25 on page 6 - 22). Place the heatsink back on the card, and secure the screws in the order indicated Figure 6 - 25 on page 6 - Attach the video card fan and secure with the screws as indicated in Figure 6 - 23 on page 6 -...
Page 137: Overview
Modules Chapter 7: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. The chapter includes information on the following: •...
Page 138: Setting Up Sata Raid Mode
Modules Setting Up SATA RAID Mode To configure your system in Striping (RAID 0) or Mirroring (RAID 1) modes (see RAID Hard Disks Table 7 - 1, on page 7 - 3) you will require at least two identical (see sidebar) hard disks.
Page 139 Modules RAID Level Description Table 7 - 1 RAID Levels Identical drives reading and writing data in parallel to increase performance. RAID 0 RAID 0 implements a striped disk array and the data is broken into blocks and each block is written to a separate disk drive.
Page 140: Sata Raid Setup Procedure (Bios)
Modules SATA RAID Setup Procedure (BIOS) Start-up your notebook computer and press <F2> to enter the BIOS. Go to the Advanced menu, select "SATA Mode" and press Enter (see page • Select “RAID”. Press Esc and go to the Boot menu. Set the DVD-ROM Drive (make sure the Microsoft Windows 7 OS DVD is inserted) as the first device in the boot order from the Boot menu.
Page 141: Raid Setup (Intel Matrix)
Modules RAID Setup (Intel Matrix) As the computer starts up press Ctrl + i to enter RAID configuration menu. Intel(R) Rapid Storage Technology - Option ROM v9.5.0.1008 Figure 7 - 1 Copyright (C) 2003-09 Intel Corporation. All Rights Reserved. [ MAIN MENU Intel(R) Rapid Create RAID Volume Recovery Volume Options...
Page 142 Modules 10. This will now return to the main menu. Intel(R) Rapid Storage Technology - Option ROM - 9.5.0.1008 Copyright (C) 2003-09 Intel Corporation. All Rights Reserved. [ MAIN MENU Figure 7 - 2 Create RAID Volume Recovery Volume Options Delete RAID Volume Acceleration Options RAID Created...
Page 143: Intel® Matrix Driver Installation
Modules Intel Matrix Driver Installation ® 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. e-SATA Port 2. Click Option Drivers (button). Install the Intel Matrix 3. Click 5.Install Matrix Driver > Yes. Storage driver to dis- 4.
Page 144: Intel® Matrix Storage Manager
Modules Intel® Matrix Storage Manager If a hard drive member of a RAID volume is reported as “Degraded” or “Failed” it may be possible to recover the volume. If the volume cannot be restored then you will need to recreate the RAID volume and restore the data from a back up. The Help menu (press F1 or select Contents and Index from the Help menu) provides in- structions on how to recover or recreate RAID Volumes.
Page 145: Raid Volume Data Verification And Repair
Modules RAID Volume Data Verification and Repair The RAID volume data verification process identifies any inconsistencies or bad data on a RAID 0 or RAID 1 volume. The table outlines what occurs for each RAID level: RAID Verify Verify & Repair Level RAID 0 Bad blocks are identified.
Page 146 Modules Verifying and Repairing RAID Volume Data Run the Intel® Matrix Storage Console from the Intel® Matrix Storage Man- ager in the Programs/All Programs menu. Click View > Advanced Mode. Right-click on the RAID volume and select either Verify Volume Data or Verify and Repair Volume Data.
Page 147: Bluetooth Module
Modules Bluetooth Module The optional Bluetooth module allows you to connect your computer to Bluetooth Wireless Device enabled devices such as other computers, desktop computers, mobile phones, print- Operation Aboard ers, digital cameras, PDAs, headsets etc. using a short-range radio frequency. Aircraft Use the Fn + F12 key combination or Touch Sensor Instant Key to toggle power The use of any portable...
Page 148: Bluetooth Configuration In Windows 7
Modules Bluetooth Configuration in Windows 7 Setup your Bluetooth Device so the Computer Can Find it Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Add a Device Make the device discoverable (to do this check your device documentation). Click Start, and click To Turn the Bluetooth Module On Control Panel and then...
Page 149 Modules To Add a Bluetooth Device Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. Pairing Options If a device has been pre- viously connected then the pairing option menu will appear when you at- tempt subsequent con- nections.
Page 150 Modules Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing. Figure 7 - 9 Pairing Codes Pairing Code Example The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection proce- dure, and may require you to confirm a pairing code is correct on both devices.
Page 151 Modules To Change Settings for the Bluetooth Device Click the taskbar icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to: Bluetooth Help • Change the name of the device (click Bluetooth, type a new name and click OK). •...
Page 152: Wireless Lan Module
Modules Wireless LAN Module If you have included an Intel® Wi-Fi Link 5300 Series, Intel® Advanced N Wi-Fi Wireless Device Link 6200, Intel® Ultimate N Wi-Fi Link 6300 module or 3rd Party 802.11b/g/n Operation Aboard WLAN module in your purchase option, make sure that the Wireless LAN module Aircraft is on before installing the driver.
Page 153: Intel® Wi-Fi Link Series Driver Installation
Modules Intel® Wi-Fi Link Series Driver Installation If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, then insert the Device Drivers & Util- ities + User’s Manual disc into the CD/DVD drive. 2.
Page 154: Connecting To A Wireless Network In Windows 7
Modules Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. Network and Click the taskbar wireless icon , and then double-click an access point to con- Sharing Center nect to or click to Open Network and Sharing Center if you do not see a network you want to connect to in the taskbar menu (a list of options will appear allowing You can also use the Net- setting changes, and creating a new network).
Page 155 Modules You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Page 156 Modules Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button). Security Enabled Networks You should try to make sure that any network you are connecting to is a se- cure network.
Page 157: Windows Mobility Center
Modules Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: Click Start, and click Control Panel (or point to Settings and click Control Panel).
Page 158: Pc Camera Module
Modules PC Camera Module Before installing the driver, make sure the PC Camera is on. Use the Fn + F11 key Latest PC Camera combination or Touch Sensor Instant Key to toggle power to the to the PC Camera Driver Information module.
Page 159: Pc Camera Audio Setup
Modules PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound).
Page 160 Modules Figure 7 - 16 Audio Setup for PC Camera Right-click 7 - 24 PC Camera Module...
Page 161 Modules Camera Application The WebCam application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. Pre-Allocating File Size/Space Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see below).
Page 162 Modules Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties).
Page 163 Modules Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. Run the camera program from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter..Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Page 164 Modules Zoom The WebCam program allows you to zoom the camera in and out. Run the camera application from the desktop shortcut. Go to Zoom and select Zoom Out/Zoom In. Figure 7 - 18 Zoom/Setting Snapshot Folder Taking Still Pictures The Snapshot folder’s default location is on the The WebCam program allows you to take still pictures.
Page 165: Tv Tuner Module
Modules TV Tuner Module If your purchase configuration includes the optional Hybrid (Analog & Digital) TV Antenna USB Mini-Card TV Tuner module, you will be supplied with a remote control unit The TV antenna sup- and appropriate antenna and fittings for the module. Software support for the TV plied with any TV Tuner Tuner module is provided by Windows Media Center in Windows 7 (not included module is intended for...
Page 166: Consumer Infrared Driver
Modules Consumer Infrared Driver 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. TV Tuner Module Support 2. Click Option Drivers (button). 3. Click 3.Install CIR Driver > Yes. Note that the TV Tuner 4.
Page 167: Digital Tv Broadcast Signal
Modules Digital TV Broadcast Signal The antenna is the most crucial factor in receiving a clear digital terrestrial TV broadcast signal. The passive antenna provided should provide a clear signal when CATV Cable Safety placed beside a window. If the signal is not clear then you can purchase an active Make sure that your antenna (it should also be placed beside a window) to improve the signal.
Page 168: Fingerprint Reader Module
Modules Fingerprint Reader Module The optional fingerprint reader Protector Suite Software provides a high level Password Warning of security for your computer. A further level of security and control is provided in the BIOS (see “Security Menu” on page 5 - 10).
Page 169: Fingerprint Reader Driver Installation
Modules Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers. 3. Click 4.Install FingerPrint Driver > Yes. 4. Windows will configure Protector Suite 2009 and automatically restart the computer.
Page 170: User Enrollment
Modules User Enrollment Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the taskbar icon (click Initialize). Fingerprint On the first run of the program you will be asked to click the Accept button to Enrollment accept the license.
Page 171 Modules Click the button above any of the fingers to begin the enrollment process for that finger. Swipe the finger until the progress bar reaches 100% to enroll that finger. Fingerprint Enrollment Note that it is strongly rec- ommended that you enroll more than one finger in case of injury etc.
Page 172 Modules Right-click the taskbar icon and select Start Control Center (and then swipe a finger) to allow you to Edit Fingerprints, register Applications, edit Settings and access the Help menu etc. You can also run the Control Center etc. from the Protector Suite item in the Programs/All Programs menu 10.
Page 173: Fingerprint Control Center Features
Modules Fingerprint Control Center Features Application Launcher Help The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the reg- For more information on istered fingers and ten click OK to close the application window.
Page 174 Modules 7 - 38...
Page 175: Troubleshooting
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Page 176: Basic Hints And Tips
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.
Page 177: Backup And General Maintenance
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.
Page 178: Viruses
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.
Page 179: Upgrading And Adding New Hardware/Software
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
Page 180 Troubleshooting • Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem.
Page 181: Problems & Possible Solutions
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution You turned the power on Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and but it doesn’t work. seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts.
Page 182 Troubleshooting Problem Possible Cause - Solution The computer feels too Make sure the computer is properly ventilated and the vents/fan intakes are not blocked. If this hot. doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...
Page 183 Troubleshooting Problem Possible Cause - Solution forget boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your password. service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Page 184 Troubleshooting Problem Possible Cause - Solution The TouchPad doesn’t The Touchpad has been disabled. Press the Touchpad toggle (Fn + F1) key combination (make work. sure you have installed the Touchpad driver. The system freezes or The system’s power saving features have timed-out. Use the AC/DC adapter, press a key on the the screen goes dark.
Page 185 Troubleshooting Problem Possible Cause - Solution When a DVD is played in This is an issue with Windows Media Player/Media Center and audio output through the S/PDIF- Windows Media Player/ Out Jack. We recommend that you use the Power DVD application to play DVDs. Media Center, the audio track in other languages (commentaries etc.) is...
Page 186 Troubleshooting Problem Possible Cause - Solution No sound can be heard You have not configured the HDMI audio output. See “HDMI Audio Configuration” on page 2 - through HDMI connected display device. After installing Where this is the case, install the beta cardreader driver version provided on the Device Drivers cardreader driver &...
Page 187 Troubleshooting Problem Possible Cause - Solution This is a known problem and Intel have provided a beta WLAN driver to address this issue. The After using the Fn + F11 beta WLAN driver is provided on the Device Drivers & Utilities +User’s Manual disc. combination switch the WLAN module Insert the Device Drivers &...
Page 188 Troubleshooting Problem Possible Cause - Solution have RAID You may need to recover the RAID volumes. enabled and the system As the computer starts up press Ctrl + i to enter RAID configuration menu will not boot to Windows. If the RAID volume’s Physical disks are marked in red, then press 4.Recovery Volume Options.
Page 189: Interface (Ports & Jacks)
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the ports & jacks which allow your computer to commu- nicate with external devices, connect to the internet etc. Interface (Ports & Jacks) A - 1...
Page 190: Ports And Jacks
Interface (Ports & Jacks) Ports and Jacks Item Description Card Reader The card reader allows you to use the following digital storage cards: MMC (MultiMedia Card) RS MMC (requires PC adapter) SD (Secure Digital) Mini SD (requires PC adapter) MS (Memory Stick) MS Duo (requires PC adapter) MS (Memory Stick Pro) Cable (CATV)
Page 191: E-Sata/Usb Port
Interface (Ports & Jacks) Item Description e-SATA/USB Port This is a combined e-SATA (external Serial Advanced Technology Attachment)/ USB 2.0 compatible port. e-SATA / Plug external Serial ATA hard drives into this e-SATA (external Serial Advanced Technology Attachment) port. See “USB 2.0/1.1 Ports”...
Page 192: Microphone-In Jack
Interface (Ports & Jacks) Item Description Microphone-In Jack Plug an external microphone in to this jack to record on your computer. Mini-IEEE 1394 Port This allows high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). IEEE 1394 The Mini-IEEE 1394 ports only support SELF POWERED IEEE 1394 devices.
Page 193: Usb 2.0/1.1 Ports
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power supply which comes with the device).
Page 194 Interface (Ports & Jacks) A - 6...
Page 195: Nvidia Video Driver Controls
NVIDIA Video Driver Controls Appendix B: NVIDIA Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - NVIDIA Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 1.
Page 196: Nvidia Control Panel (Win 7
NVIDIA Video Driver Controls NVIDIA Control Panel (Win 7) More advanced video configuration options are provided in the NVIDIA Control NVIDIA Control Panel tab. Panel Open the Display Settings (see page 17) control panel. To access the Ge- Click Advanced Settings (button). Force..
Page 197 NVIDIA Video Driver Controls The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as display configuration, 3D Settings and Help menus etc. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page.
Page 198 NVIDIA Video Driver Controls The Help menus provide index and search features, and direct links to the NVIDIA website etc. Figure B - 3 Help Menu B - 4 NVIDIA Control Panel (Win 7)
Page 199: Display Devices
NVIDIA Video Driver Controls Display Devices Note that you can use a DVI cable connected to the DVI-Out port, or an HDMI Display Devices (High-Definition Multimedia Interface) cable connected to the HDMI-Out port to connect an external display (if you are using an older type of monitor you can use a Besides built-in converter to convert the signal from DVI to VGA).
Page 200: Display Modes
NVIDIA Video Driver Controls Display Modes Single Display Mode SLI Configuration & Only one of your displays is used. Multiple Displays Note that if SLI configu- Duplicate Displays ration is enabled only a Duplicate simply shows an exact copy of the Primary display desktop on the other Single display may be display(s).
Page 201 NVIDIA Video Driver Controls Configuring an External Display using the NVIDIA Control Panel You can use the NVIDIA control panel to configure any attached displays. Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Display Not Shown Go to NVIDIA Control Panel (see page If the attached display...
Page 202 NVIDIA Video Driver Controls Duplicating the Displays Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to NVIDIA Control Panel (see page Double-click Display (if the sub-menus are not visible), and then click Set up multiple displays.
Page 203 NVIDIA Video Driver Controls Extending the Display Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to NVIDIA Control Panel (see page Double-click Display (if the sub-menus are not visible), and then click Set up multiple displays.
Page 204 NVIDIA Video Driver Controls Changing the Primary Display on Extended Displays If you want to switch the primary display if the displays are extended then right- click the secondary display icon. Select Make this the Windows primary display. Click Apply > Yes to save the change. Figure B - 7 Switch Primary Display...
Page 205: Attaching Other Displays (Win 7
NVIDIA Video Driver Controls Attaching Other Displays (Win 7) Configuring an External Display in Windows 7 Function Key Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Combination Go to the Screen resolution control panel. You can use the Fn + F7 Click the Detect button.
Page 206 NVIDIA Video Driver Controls You can configure the displays from the Multiple Displays menu. Figure B - 9 Screen Resolution Multiple Display Options (Win 7) • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) •...
Page 207 NVIDIA Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configura- tion and modes (this is particularly useful when attaching a projector) in Windows 7. Attach your external display to the external monitor port and turn it on.
Page 208: Sli Multi Gpu Configuration
NVIDIA Video Driver Controls SLI Multi GPU Configuration This computer features an NVIDIA Scalable Link Interface (SLI) that improves SLI Configuration & graphic quality and performance by combining dual NVIDIA GPUs (two video Multiple Displays cards are required) in a single system. To enable/disable SLI Configuration: Note that if SLI configu- Go to NVIDIA Control Panel (see page ration is enabled only a...
Page 209: Sli Multi Gpu Configuration & Battery Power
NVIDIA Video Driver Controls SLI Multi GPU Configuration & Battery Power Note that due to the high power and system demands created by enabling SLI Con- figuration, you should not enable SLI configuration if your computer is powered by battery only. If you attempt to run an SLI configuration when the computer is powered by the battery only, then system problems may occur.
Page 210: Enabling Tv Display
NVIDIA Video Driver Controls Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an Detect Displays HDMI cable/DVI cable from the TV to the HDMI-Out port/DVI-Out port (if sup- ported by your TV). To get a full range of dis- play options click “My dis- You will need to enable the TV display from the NVIDIA Control Panel as per the...
Page 211: Changing The Tv Signal Format
NVIDIA Video Driver Controls Changing the TV Signal Format When the TV is enabled as a display device click the sub-menus under Video & Television. Click “Change the signal or HD format”. Select the connector or format you want to use (the menu that appears will depend upon your type of connector).
Page 212 NVIDIA Video Driver Controls The NVIDIA Control Panel provides additional configuration controls to adjust the TV settings in the Video & Television menu. Figure B - 14 NVIDIA Control Panels (Video & Television) B - 18 Enabling TV Display...
Page 213: Specifications
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Page 214: Processor
Specifications Processor Display BIOS Intel® Core i7-720QM Processor: 18.4" HD+/ FHD (1920 * 1080) TFT LCD One 32Mb Flash ROM 1.6GHz Phoenix™ BIOS Memory 45nm (45 Nanometer) Process Storage Technology, 6M L3 Cache & DDRIII (DDR3) Dual Channels FSB 1333MHz - TDP 45W Two 204 Pin SO-DIMM Sockets Up to three (Factory Option) rPGA988A Package...
Page 215: Keyboard & Pointing Device
Specifications Keyboard & Pointing Device Interface Communication Full Size Winkey Keyboard with Numeric Four USB 2.0 Ports Built-In 10/100/100 Base-TX Ethernet LAN Keypad One eSATA Port Bluetooth 2.1 + EDR (Enhanced Data Built-In TouchPad (with Multi Gesture One Mini-IEEE1394a Port Rate) Module (Factory Option) Functionality) One DVI-Out Port (with CRT out)
Page 216: Operating System
Specifications Operating System Environmental Spec Windows® 7 Temperature ° ° Note that the TV Tuner module (factory) Operating: C - 35 option in is supported by the Windows Non-Operating: -20°C - 60°C Media Center software. Windows Media Relative Humidity Center is not included in Starter or Operating: 20% - 80% Home Basic versions of Windows 7.

EUROCOM Notebook User Manual

Quick Start Guide

Storage Devices, Mouse, Audio & Printer

Power Management

Drivers & Utilities

BIOS Utilities

Upgrading the Computer

Modules

Troubleshooting

Interface (Ports & Jacks)

NVIDIA Video Driver Controls

Specifications

Quick Links

Need help?

Questions and answers

Related Manuals for EUROCOM Notebook

Summary of Contents for EUROCOM Notebook